Cisco D9854i Manual

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 187 
 
The following describes each mode: 
Data Port 
Management Port 
Description 
No Output Disables the MPEGoIP interface. 
Always Output Always output data on the port. 
19 Click OK. 
20 The MoIP Output Status section displays the current Output bit Rate (0 to 213 
Mbps) and the available bit bandwidth (Free Bandwidth), in Mbps. 
21 Click Apply. 
If a conflict occurs, a detailed error message appears at the top of the page. You...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
188 78-4021470-01 Rev J 
2 For each DPM Program Entry, it displays the input channel number (Chl #) and 
channel name (Name), whether the PE is passed, dropped, or mapped (Action), 
the output channel (Output Ch#), and the PMT PID (PMT PID).  
Note: Any changes made to the DPM Program Entry Setup configuration 
automatically changes the Output Mode to Full DPM Control in the MPEG over 
IP Output page. 
3 Select the program entry you want to edit. 
4 The...

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 189 
 
Action Description 
Map Provides the flexibility to define all the outgoing PID numbers for 
a PE, including those not currently on transmission. 
11 Enter a Stream Type to map within a PE to a specified PID (0 to 255). 
12 Select the output program stream Category or service type. This value is only 
used if the Action is set to Map. The categories are: UNKN, CDT, LSDT, DATA, 
TTX, MPE, DPI, VBI, SUBT, AUD, VID, PCR or INVL. 
13...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
190 78-4021470-01 Rev J 
Map Mode Description 
Svc ID & PID Channels and the elementary service PIDs can be mapped. 
21 Select the Duplication Method of the DPM program, which modifies the PSI to 
duplicate a program and its content. This parameter is only used if Remapping 
Mode is set to Svc ID & PID. The following table describes the each duplication 
method: 
Duplic Mode Description 
PSI Remap Every input PID can be mapped to one output PID. If PID...

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 191 
 
PSI Rate Description 
SA Std  Transmits the generated PSI tables based on PowerVu standard 
intervals. 
25 The PSI Table Output Option drop-down allows the operator to specify which 
PSI tables to include in the program/output stream. The following table 
describes each option: 
PSI Options Description 
Pass All Transmits the incoming PSI Tables as is; does not modify the 
content and rate. 
Drop All Does not transmit any PSI...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
192 78-4021470-01 Rev J 
30 Click Apply. 
If a conflict occurs, a detailed error message appears at the top of the page. You 
must resolve the conflict and then click Apply to save and apply your changes 
again.  
Typical set up for Digital Program Mapping (DPM) 
1 Verify that you are receiving a valid signal and that you have set up the channels 
that you want to pass, drop, or map. 
2 From the user interface of the D9854, click Transport Stream. 
3...

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 193 
 
Parameter Description 
CAT  Regen 
PMT Regen 
TSDT Drop 
NIT Regen or Drop 
NITO Drop 
SDT Regen 
SDTO Drop 
BAT Drop 
EIT Drop 
TDT Pass 
RST Pass 
TOT Pass 
DIT Pass 
SIT Pass 
ECM Drop 
EMM Drop 
DRT Drop 
CDT Drop 
16 Click OK. 
17 Click Apply. 
  

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
194 78-4021470-01 Rev J 
Configuring System Settings 
Viewing the System Identification 
1 From the user interface of the D9854, click System Settings > System > 
Identification. The Identification page is displayed. 
 
2 The System page displays the parameters associated with the D9854 system, such 
as serial number, model number, and user addresses. 
3 You may optionally change the Hostname (device name) and click Apply.    

 
 
 Configuring System Settings 
 
78-4021470-01 Rev J 195 
 
Viewing Hardware Features and Base License Information 
From the user interface of the D9854, click System Settings > System, expand 
Identification and then click Features/Licenses. The Features/Licenses page is 
displayed. 
 
The Hardware Features section displays the hardware options installed in the 
current D9854 Advanced Program Receiver. For example, it indicates whether the 
receiver equipped with an SDI output and the number of...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
196 78-4021470-01 Rev J 
Setting up IP Information 
1 From the user interface of the D9854, click System Settings > System > IP 
Settings. The IP Settings page is displayed. 
 
2 In the top section, you can set the parameters for communicating with other 
equipment via the Ethernet Data and Management ports for IP applications and 
upgrading application software.  
3 Select control or data settings and set the IPv4 Destination IP Address for the...