Cisco D9854i Manual

 
 
 Setting up Input Information 
 
78-4021470-01 Rev J 147 
 
Setting up the Channel Selections 
1 From the user interface of the D9854, click Input > Channel > Channel 
Selection. The Channel Selection page is displayed. 
 
2 Enter a channel number for up to 16 program entries. Alternatively, use the 
drop-down arrow to select an available channel. 
Note: Only PE1 supports PowerVu descrambling. Do not assign PowerVu 
channels to PE2 to PE16. If any PowerVu channels are assigned to PE2 to PE16, 
all...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
148 78-4021470-01 Rev J 
Viewing the Channel Status 
From the user interface of the D9854, click Input > Channel > Channel Status. The 
Channel Status page is displayed. 
 
The following table describes the channel information displayed: 
Parameter Description 
PE Index Indicates the Program Entry number (PE1 to PE16). 
Channel Displays the input channel of the current PE. The channel is 
displayed in a range from 1 to 65535. 
Channel Name Displays the...

 
 
 Setting up Input Information 
 
78-4021470-01 Rev J 149 
 
Parameter Description 
SR Status Displays the status of an alternate authorized program/service 
from the same transport stream when the receiver is not 
authorized to view the primary program.This is an uplink 
initiated function that maps the alternate service to the original 
(primary) service PIDs, replacing the original service with the 
alternate service at the digital transport output. No local 
intervention is required by the...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
150 78-4021470-01 Rev J 
Configuring the Common Interface (CI) Information 
1 From the user interface of the D9854, click Input > Conditional Access > CI 
Setup. The CI Setup page is displayed. 
 
2 Select Enable in the CI CAM QUERY Support drop-down to query the CAM 
prior to decryption to ensure that the card can be decrypted. The default is 
Disable. 
3 Select Enable in CI CAM Auto Reset to automatically reset the card. The default 
is Disable. 
4 In...

 
 
 Setting up Input Information 
 
78-4021470-01 Rev J 151 
 
8 Select the CAM slot (CI Slot) to use for decryption. If you set the CI slot to 
AUTO for PE1, the software automatically assigns the slot capable of decrypting 
the stream.  
Note: If CI Slot is set to AUTO, Decrypt must be set to ON. 
Select TOP to use the top CAM slot for decryption or select BOTTOM to use the 
bottom CAM slot for decryption. 
9 The Decryption Mode Determines whether to decrypt the channel or to specify 
the specific...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
152 78-4021470-01 Rev J 
If you set by Parameter Settings 
PID ID Set Mode to PID and enter PID number. 
Stream Type Set Mode to Stream, select Stream Category (AUD, VID, SUBT, TTX, 
or USER) and enter Stream Instance of the stream type. 
There is an additional configuration if you select user as the Stream 
Category (see below). 
Stream Type: User Set Mode to Stream, Stream Category to User, manually enter the 
stream code in Stream Type Value, and then...

 
 
 Setting up Input Information 
 
78-4021470-01 Rev J 153 
 
Viewing the Common Interface (CI) Status 
From the user interface of the D9854, click Input > Conditional Access, expand CI 
Setup and then click CI Status. The CI Status page is displayed. 
 
The following table describes the CI Status: 
CI Status Description 
CI Slot Indicates whether it is the top slot (TOP) or the bottom slot 
(BOTTOM). 
CAM Status Status of the CAM (Ready or Not Ready). 
Sys Name System name of the CAM. 
Comp Name...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
154 78-4021470-01 Rev J 
Viewing the CA Status 
From the user interface of the D9854, click Input > Conditional Access > CA Status. 
The CA Status page is displayed. 
 
The following describes the columns in the CA Status table: 
Status Description 
Index The ISE number. 
ISE User Address The ISE User Address. It is a 11 digit address in the following 
format: ###-###-####-#. 
ISE Version Number The ISE version number. It consists of 7 characters. 
Enc...

 
 
 Setting up Input Information 
 
78-4021470-01 Rev J 155 
 
Setting up the BISS Mode 
1 From the user interface of the D9854, click Input > Conditional Access > BISS. 
The BISS page is displayed. 
 
2 Select the Basic Interoperable Scrambling System (BISS) Mode for the receiver 
(Mode 1 or Mode E). All channels assigned to the PE identified as BISS CA-
controlled in the PMT will be decrypted. 
3 If you selected BISS Mode 1, enter a fixed 12-character BISS Mode-1 Session 
Word. Once entered it cannot...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
156 78-4021470-01 Rev J 
Viewing the PSI Tables 
From the user interface of the D9854, click Input > Stream Details > PSI Tables. The 
PSI Tables page is displayed. 
 
You cannot make any changes in the PSI table and can only view the PSI tables 
received and their settings. The following is a list of the various columns: 
Abbreviation  Description 
Table Type Indicates the MPEG table acronym. 
PAT, CAT, PMT, TSDT, NIT, NIT Other, SDT, SDT Other, 
BAT,...