Cisco D9854i Manual

 
 
 Setup Menu 
 
78-4021470-01 Rev J 97 
 
  
M1/M2 
Menu Item Description Parameters 
M1 Port Type This option allows the operator 
to set the output format for the 
M1 port. 
ASI or SDI 
M2 Port Type This option allows the operator 
to set the output format for the 
M2 port. 
ASI or SDI 
  
TS Out - ASI 
Menu Item Description Parameters 
Name Displays the name assigned 
to the transport output for 
ease of reference. This is 
read-only. 
20-character string 
Rate Control Select the output rate...

 
Chapter 4    Front Panel Operation  
 
 
98 78-4021470-01 Rev J 
Menu Item Description Parameters 
User Rate(Mbps) If the Rate Control was set to 
User, set the maximum 
output bit rate. If null 
packets are inserted, this will 
be the output rate. 
This setting is used when the 
signal source is RF or ASI 
and allows you to set the 
output bit rate to a value 
expected by equipment 
connected to the ASI output. 
0 to 213 Mbps 
Note: Output data may be lost if this bit rate 
is set to a value less than...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 99 
 
Menu Item Description Parameters 
Output Mode Select the DPM output mode 
for the current output. 
With the exception of No 
Output, selecting a mode 
will configure the DPM 
settings to achieve the 
specified behavior. In this 
way, they act as DPM 
presets. 
Any changes then made to 
the DPM settings will switch 
the mode to Full DPM 
Control. 
It is highly recommended to 
use either one of these basic 
modes, or, for advanced 
setup, enter the DPM 
mapping...

 
Chapter 4    Front Panel Operation  
 
 
100 78-4021470-01 Rev J 
Menu Item Description Parameters 
Descramble 
Mode 
Select whether the output 
will be descrambled if the 
input is scrambled. 
Scrambled - The output channel will remain 
scrambled even if the PE is authorized and 
can descramble the channel. 
Descrambled - Descrambles the output 
channel, and passes in-the-clear channels.
  
The default is Descrambled. 
Insert Null 
Packet 
Select whether to insert null 
packets into the output to...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 101 
 
Menu Item Description Parameters 
Output Mode This selects the DPM 
output mode. 
No Output - No MPEGoIP output will be 
generated.  
Passthrough - The output will be identical to 
the input. The output channel will not be 
modified. 
PE/PID remapping options, PSI regeneration 
and User Rate are not supported in this mode.
  
Service Chans Only - Only service channels 
will be output.  
MAP Passthrough - The output will be 
identical to the input, except that...

 
Chapter 4    Front Panel Operation  
 
 
102 78-4021470-01 Rev J 
Menu Item Description Parameters 
Descramble 
Mode 
This parameter selects 
whether the receiver 
should scramble the 
output even if it is 
authorized to receive the 
channel. 
The default mode is Descrambled. 
Scrambled - Scrambles the output channel 
even if the PE is authorized and can 
descramble the channel.  
Descrambled - Descrambles the output 
channel, and passes in-the-clear channels. 
Insert Null 
Packet 
This parameter...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 103 
 
Menu Item Description Parameters 
PCR@IP Start This selects whether to 
always transmit a new IP 
packet when a new 
Program Clock Reference 
(PCR) arrives. 
Yes or No 
SAP This selects whether to use 
the configured SAP string 
as the channel name. 
Yes or No 
MGMT Port 
Mode, DATA 
Port Mode 
This selects the 
Management and Data 
MPEGoIP modes.  
Note: If No Output was 
selected for MOIP1 Output 
Mode, updates to the port 
modes will have no affect. 
No...

 
Chapter 4    Front Panel Operation  
 
 
104 78-4021470-01 Rev J 
The DPM menu has the following structure: 
  
DPM - Global 
Menu Item Description Parameters 
Resync All: Select to resynchronize all DPM 
output with the PMT data for 
all program entries on the 
selected output. 
ASI 
Regenerate Selects whether to regenerate 
the PSI tables in the output. 
Always or As Needed 
Always - All tables are regenerated. 
As Needed - Only regenerate the 
tables if the content has changed. 
Copy: This copies...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 105 
 
ASI/MOIP1 
Menu Item Description Parameters 
PE Select the Program Entry to 
configure. 
1 to 16 
InCh Displays the channel number to 
which the PE is tuned. This is 
read-only. 
1 to 65535 
PMT Indicates the input PID value of 
the Program Map Table for the 
current channel. This is read-
only. 
2 to 8190 
Act Selects the action to perform on 
the current program entry. 
This setting controls the overall 
DPM behavior of the PE and 
will affect how the PID...

 
Chapter 4    Front Panel Operation  
 
 
106 78-4021470-01 Rev J 
Menu Item Description Parameters 
PID Press Select to view and 
configure the PID map. The PID 
map is used to map input 
services to output PIDs. For 
more information, see PID Map 
Menu (on page 108). 
 
Map Mode Select the DPM mapping mode 
for the current output. 
Svc ID - The elementary PIDs are not 
changed. Channels are remapped by 
changing their PSI references. When 
this mode is selected, PID mapping in 
the PID Map menu is...