Cisco D9854i Manual

 
 
 Setup Menu 
 
78-4021470-01 Rev J 87 
 
  
Audio Slot 
Menu Item Description Parameters 
Group, Slot 

 
Chapter 4    Front Panel Operation  
 
 
88 78-4021470-01 Rev J 
Menu Item Description Parameters 
Language List If Language List was 
selected in the Select 
Language By menu, select 
the MPEG language to 
display. 
ara (Arabic), btk (Batak (Indonesia), ben 
(Bengali), bul (Bulgarian), chi (Chinese), 
cze (Czech), dan (Danish), dut (Dutch), 
eng (English), fin (Finnish), fre (French), 
ger (German), gre (Greek), heb 
(Hebrew), hin (Hindi), hun (Hungarian), 
ice (Icelandic), ind (Indonesian), ita...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 89 
 
Menu Item Description Parameters 
BackGnd Sets the text background for 
Imitext subtitles.  
Auto - Uses the uplink subtitling 
equipment setting. 
Shadow - Applies an outline to the right 
side of each text character. No 
background box is applied to subtitles, 
i.e., text is visible directly on top of 
video. 
Opaque - Applies a black box to each 
text character. 
Semi - Applies a semi-transparent box to 
subtitle text. 
None - No shadow or outline is...

 
Chapter 4    Front Panel Operation  
 
 
90 78-4021470-01 Rev J 
 
Setup Menu: Common Interface (CI) 
To view the CI menus from the Main menu, press the RIGHT arrow key once and 
then the SELECT key to reach the Setup menu. Then press the RIGHT arrow key 
four times and the SELECT key to view the CI menu. 
The Common Interface (CI) slots are located under the door on the front panel. They 
allow use of a CAM (Conditional Access Module) Smart Card to decrypt purchased 
programming. 
You must be...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 91 
 
CI 
Menu Item Description Parameters 
PE Select the Program Entry (PE) to 
configure the decryption settings. 
PE1 to PE16 
Decrypt Determines whether to decrypt the 
channel or to specify the specific 
components to decrypt. 
ON (default) - Decrypts the 
entire program entry. 
OFF - Disables decryption for 
the current program entry. 
Comp - Allows specific 
components to be decrypted, as 
specified in the component list. 
Note: If the CI Slot is set to 
Auto...

 
Chapter 4    Front Panel Operation  
 
 
92 78-4021470-01 Rev J 
Menu Item Description Parameters 
Idx Select the component record to 
edit. 
1-64 (up to 32 records for each 
CAM) 
PE Set the Program Entry the 
component is located. 
1 to 16 
Mode Select whether to choose the 
component by PID or by stream 
type. 
PID or STREAM 
PID If decrypting by PID, set the PID 
number. 
0 to 8192 
Stream If decrypting by stream type and 
set the stream type. 
AUD (audio), VID (video), 
SUBT (subtitles), TTX...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 93 
 
Menu Item Description Parameters 
ON_ID Specify the Transport Original 
Network ID. 
0 to 65535 
TS Routing Select EntireTS to use the CAM to 
decrypt the entire transport 
stream, or select ServicesOnly to 
use the CAM to decrypt only the 
PIDs being used by the active 
services. 
EntireTS or ServicesOnly 
   
Top/Bottom Slot 
Menu Item Description Parameters 
CAM Status 
Overview 
View the status of the CAM that is located 
in the top or bottom slot. 
Top...

 
Chapter 4    Front Panel Operation  
 
 
94 78-4021470-01 Rev J 
 
Setup Menu: Outputs 
To view the Outputs menus from the Main menu, press the RIGHT arrow key once 
and then the SELECT key to reach the Setup menu. Then press the RIGHT arrow 
key five times and the SELECT key to view the Outputs menu. 
The Outputs menu allows you to set up the rear panel control relays for alarms, cue 
tones and cue triggers, and the transport stream outputs, and Digital Program 
Mapping (DPM). 
For instructions on how...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 95 
 
Cueing 
Menu Item Description Parameters 
Cueing Mode Select whether cueing output 
should be DTMF tones or 
trigger pins. 
Trigger or Tone 
Tone - Cue tones are standard Dual-
Tone Multi-Frequency (DTMF) tones. 
The tones are generated at the Cue 
Tone/Relay output on the rear panel 
of the receiver. 
Trigger - Cue trigger refers to open-
collector pins which can be toggled at 
the Cue Tone/Relay output on the 
rear panel of the receiver. 
Trigger Polarity If...

 
Chapter 4    Front Panel Operation  
 
 
96 78-4021470-01 Rev J 
Menu Item Description Parameters 
Tones Sets the three digit tone 
sequence. 
000 to 999 
Mode Sets the tone sequence mode. * - Start tone only 
# - End tone only 
*/# - Start and end tones. The end 
tone is signaled after waiting the time 
specified in Delay(sec). 
Delay(sec) If the Mode was set to */# 
(Start/Stop), set the delay, in 
seconds, between the start and 
stop sequences. 
1 to 255. The default is 30. 
Relay Mode The relay can...