Cisco D9854i Manual

 
 
 Setup Menu 
 
78-4021470-01 Rev J 67 
 
Menu Item Description Parameters 
Orbital Position 
Validation Date 
This displays the last date that the ‘Validate 
Orbital Position’ operation was performed. 
N/A 
Freq (GHz) This is the current Downlink operating 
frequency used by the receiver for tuning the 
received digital signal. 
0.0 to 15.0 GHz 
SymRate This is the symbol rate. The symbol rate must 
match that of transmitted signal. 
1.0 to 45.0 Ms/s for DVB-
S. 
1.0 to 30.0 Ms/s for DVB-
S2 if Pilot...

 
Chapter 4    Front Panel Operation  
 
 
68 78-4021470-01 Rev J 
Menu Item Description Parameters 
InputIQ Select the Input signal spectrum inversion 
setting, which allows the operator to track and 
select inverted and non-inverted digital 
signals. This is normally used to automatically 
reject or filter out unwanted signals. 
Auto, Normal, or 
Opposite. 
Auto - The signal is 
tracked and inverted for 
correct selection, as 
required.  
Opposite - The signal is 
always inverted. 
Normal - The signal...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 69 
 
    
Tune Mode 
Custom 
This menu is where you set up your custom properties. Select the channel to set up 
and then edit it. 
Menu Item Description Parameters 
Services List Mode If using custom tune mode, 
select which tables are required 
for tuning. 
Degraded or Rigorous.  
Rigorous - Requires all service list tables 
to be present to acquire the signal. 
Degraded - Requires any service list 
table to be present to acquire the signal. 
BAT This is not...

 
Chapter 4    Front Panel Operation  
 
 
70 78-4021470-01 Rev J 
Menu Item Description Parameters 
BAT This is not supported in the 
current release. 
No 
NIT Indicates whether the Network 
Information Table (NIT) is being 
used to create the service list. 
Yes or No 
SDT Indicates whether the Service 
Description Table (SDT) is being 
used to create the service list. 
Yes or No 
PAT Indicates whether the Program 
Association Table (PAT) is being 
used to create the service list. 
Yes or No 
Frequency...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 71 
 
  
Setup Menu: IP 
To view the IP menu from the Main menu, press the RIGHT arrow key once and the 
then the SELECT key to reach the Setup menu. Then, press the RIGHT arrow key 
twice and the SELECT key to view the IP menu. 
The IP menu allows you to set the parameters for communicating with other 
equipment via the Ethernet Data and Management ports for MPEGoIP and MPE 
applications and upgrading application software. 
For instructions on how to select and...

 
Chapter 4    Front Panel Operation  
 
 
72 78-4021470-01 Rev J 
IP 
Menu Item Description Parameters 
Port ID Select the Ethernet interface to 
configure. 
1, 2, or 3. Interface 1 is the control and 
management interface and interface 2 
and interface 3 are data interfaces. 
The default is 1. 
Description Sets the description or name for the 
Ethernet interface. 
Up to 20 alphanumeric characters in 
length. 
V4/V6 Select the IP protocol. Only IPv4 is currently supported. 
IP Address Sets the IPv4 IP...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 73 
 
Menu Item Description Parameters 
Multicast 
Forwarding 
Sets whether all the MPE data is 
forwarded to the network. It can 
forward up to 5 MPE PIDs.  
Note: This can only be configured on 
Port 2. Port 1 is fixed to Forward 
None. 
Note: The receiver supports up to a 
maximum of 10 Mbps throughput 
when forwarding 1500 byte packets.  
Forward None or Forward All 
SNMP Read 
Community String 
Sets the password to read data from a 
device and to display...

 
Chapter 4    Front Panel Operation  
 
 
74 78-4021470-01 Rev J 
Menu Item Description Parameters 
Password 
Complexity 
Sets the password complexity for all 
users. The complexity level changes 
will only affect the new user accounts 
and password changes. It will not 
affect existing accounts. 
No Checking, Minimal Checking, or 
Full Complexity Checking 
For more information, see the 
Password Complexity table below. 
SNTP Server Sets the NTP server address. If the 
NTP server address is not set...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 75 
 
Trap Destinations 
Menu Item Description Parameters 
Trap IP Address Sets the destination IP address for SNMP 
trap messages for system events (for 
example, fault messages). 
Up to 12 digits in length, e.g., 
155.128.100.200 
Ins, Del You can choose to Insert or Delete entries. 
Up to 25 entries can be assigned to the Trap 
IP Address and Community String fields. 
To add a new entry, press Ins and enter the 
new entry in the IP Address or Community 
String...

 
Chapter 4    Front Panel Operation  
 
 
76 78-4021470-01 Rev J 
Menu Item Description Port Number Parameters 
SNMP Controls SNMP access to the 
IRD. Select Enable to allow 
SNMP connections. Select 
Disable to disable the listener 
for the SNMP port. 
UDP port #161 Enable (default) or Disable 
By enabling or disabling the protocols, dynamic hardware and software firewalls are created 
for the D9854 receiver.  
Accessing TCP and UDP Services 
The following describes the commands used to access port...