Cisco D9854i Manual

 
 
 Setup Menu 
 
78-4021470-01 Rev J 107 
 
Menu Item Description Parameters 
PSI Options Select the action to perform on 
the PSI tables for the output 
stream. 
Note: The table menus (PAT, 
CAT, PMT, TSDT, NIT, NITO,  
SDT, SDTO, BAT, EIT, TDT, 
RST, TOT, DIT, SIT, ECM, 
EMM, DRT, CDT) will only 
appear if you select Ctl by 
Table. 
Pass All - Transmits the incoming PSI 
Tables as is; does not modify the 
content and rate. The PSI Rate and 
table settings are ignored. 
Drop All - Does not transmit...

 
Chapter 4    Front Panel Operation  
 
 
108 78-4021470-01 Rev J 
Menu Item Description Parameters 
PE Resync: All, 
Template, PIDs, Svcs 
Each PE output can be 
synchronized to its input 
according to one of four output 
modes. For information on 
synchronizing output services, 
see Synchronizing Output 
Services (on page 112). 
Note: The resynchronization 
will not synchronize the inputs 
if there is no valid input on the 
PE or if the PE is set to channel 
0. 
Svcs - Map the input to the output...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 109 
 
Menu Item Description Parameters 
PID Displays the input PID that will 
be mapped by the current 
entry. This value is read-only 
and for reference purposes. 
1 to 8190 
Act Select the action to perform on 
the current PID. 
The Drop action is always 
performed, but the Map option 
is only applied if the PE action 
is Map and the Map Mode is 
Svc ID & PID. 
Map - The service selected by the 
OutType and Instance will be 
mapped to the specified PID. This is...

 
Chapter 4    Front Panel Operation  
 
 
110 78-4021470-01 Rev J 
Setting Mode Options Description Default 
NITO Pass, Drop, PwRC Network Information 
Table - Other 
Pass 
SDT Pass, Drop, Regen, PwRC Service Description Table Pass 
SDTO Pass, Drop, PwRC Service Description Table 
- Other 
Pass 
BAT Pass, Drop, PwRC Bouquet Association 
Table 
Pass 
EIT Pass, Drop Event Information Table Pass 
TDT Pass, Drop Time and Date Table Pass 
RST Pass, Drop Running Status Table Pass 
TOT Pass, Drop Time Offset...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 111 
 
LCD Setting Description 
Drop Removes the service and its associated PMT reference 
from the transport output.  
Pass Permits the source content and PMT reference to 
appear in the transport output with the same 
references. 
Map Provides the flexibility to define all the outgoing PID 
numbers for the PE, including those not currently on 
transmission. 
5 Use the RIGHT arrow key to move to the right and select PID to display the 
detailed menu level. 
6...

 
Chapter 4    Front Panel Operation  
 
 
112 78-4021470-01 Rev J 
Parameter  Description 
NIT Regen or Drop 
NITO Drop 
SDT Regen 
SDTO Drop 
BAT Drop 
EIT Drop 
TDT Pass 
RST Pass 
TOT Pass 
DIT Pass 
SIT Pass 
ECM Drop 
EMM Drop 
DRT Drop 
CDT Drop 
10 Press MENU three times to exit the TS Out menu and save the data. If the 
changes cannot be saved/made, a message will be displayed indicating Bad 
configuration data. The following options are available: Abandon, Exit or 
Return. Select Return to...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 113 
 
To synchronize the output to the input PIDs only: 
This operation synchronizes the inputs to the outputs according to the PID 
assignments only. This is useful when you have already have the services set up but 
want to synchronize to the incoming PIDs.  
1 On the DPM menu, map the output services as desired. 
2 Select PE Resync: PIDs. The receiver will synchronize the PE output according to 
the input PIDs only, and ignore the service assignment...

 
Chapter 4    Front Panel Operation  
 
 
114 78-4021470-01 Rev J 
 
Setup Menu: CA 
To view the CA menu from the Main menu, press the RIGHT arrow key once and 
then the SELECT key to reach the Setup menu. Then press the RIGHT arrow key six 
times and the SELECT key to view the CA menu. 
The CA menu provides information about the ISE, the status of the ADP 
transmission, and allows you to set the BISS mode and session words available from 
your service provider. The CA menu has the following structure:...

 
 
 Setup Menu 
 
78-4021470-01 Rev J 115 
 
Menu Item Description Parameters 
ADP Enc Total Indicates the total number of 
encrypted Addressable Data Packets 
received. Ideally, the ADP Enc Pass 
and ADP Enc Total numbers should 
be identical. 
 
ADP Non-Enc Pass Indicates the number of non-
encrypted Addressable Data Packets 
successfully processed. Ideally, the 
ADP Non-Enc Pass and ADP Non-
Enc Total numbers should be 
identical. 
 
ADP Non-Enc Total  Indicates the total number of non-
encrypted...

 
Chapter 4    Front Panel Operation  
 
 
116 78-4021470-01 Rev J 
Menu Item Description Parameters 
BISS-E IID If BISS Mode is Mode E, enter the 
injected ID. 
14-character password. Once 
entered, it cannot be viewed and 
it is only displayed as asterisks 
(*). 
Contact your program provider 
for the session word. 
   
Setup Menu: Alarm/Warning 
To view the Alarm/Warning menu from the Main menu, press the RIGHT arrow 
key once and then the SELECT key to reach the Setup menu. Then press the RIGHT...