Cisco D9854i Manual

 
 
 Setting up Audio and Video Information 
 
78-4021470-01 Rev J 167 
 
Mode Description 
PCM Samples If the audio source is MPEG Layer II format, the output will be 
routed to the SDI output as PCM.  
Compressed If the audio source is AES compressed, the output will routed to the 
AES-3id output, compressed. 
When Digital Out Preference is set to PCM Samples, the output is PCM 
regardless of whether its MPEG, Dolby Digital (AC-3) or AAC audio. 
Additionally, when the output is Compressed, MPEG-1 L1...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
168 78-4021470-01 Rev J 
10 In the SDI Audio Group Setup section, select the audio source (1 or 2) in the 
Audio Decode column and the source audio channel (1 or 2) in the Channel 
column for Group Slot 1 to 4. The Group Slot is the HANC position. 
11 The Audio Status section displays the current audio settings. The following table 
describes the audio status information: 
Audio Status Description 
Audio  Displays the current audio deocder status. 
PID...

 
 
 Setting up Audio and Video Information 
 
78-4021470-01 Rev J 169 
 
Setting up Cueing Parameters 
1 From the user interface of the D9854, click Audio & Video > Other Outputs > 
Cueing. The Cueing page is displayed. 
 
2 In the Cueing Mode drop-down menu, select whether cueing output should be 
DTMF tones or trigger pins. 
Tones are standard Dual-Tone Multi-Frequency (DTMF) tones. The tones are 
generated at the Cue Tone/Relay output on the rear panel of the receiver. 
Trigger refers to...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
170 78-4021470-01 Rev J 
6 If the Cueing Mode was set to Tone, enter the Silence Duration of each silence 
between tones, in milliseconds. The duration is in the range from 0 to 80. The 
default is 40. 
7 Select the Relay Mode that can be programmed to respond to an Alarm state, 
Warning statue, or the state of one of the eight cue trigger pins. The response is 
generated at the Cue Tone/Relay output on the rear panel of the receiver. The 
following table...

 
 
 Setting up Audio and Video Information 
 
78-4021470-01 Rev J 171 
 
Setting up Cue Tone Test 
1 From the user interface of the D9854, click Audio & Video > Other Outputs, 
expand Cueing and then click Cue Tone Test. The Cue Tone Test page is 
displayed. 
 
2 In the Test Tones field, specify the three digit tone sequence. You can enter a 
value between 000 and 999. 
3 In the Sequence Mode drop-down list, select the tone sequence mode. The 
following describes the available options: 
- * - Start tone...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
172 78-4021470-01 Rev J 
Setting up Cue Tones 
1 From the user interface of the D9854, click Audio & Video > Other Outputs, 
expand Cueing and then click Cue Tone. The Cue Tone page is displayed. 
 
2 The Sequence Number lists the tone sequences. The receiver supports up to 16 
tone sequences. You can configure the state, tones, mode, and delay for each tone 
sequence. 
3 Set the Sequence State (Enabled or Disabled) of the current tone sequence. When...

 
 
 Setting up Audio and Video Information 
 
78-4021470-01 Rev J 173 
 
Setting up SDI 
1 From the user interface of the D9854, click Audio & Video > Other Outputs > 
SDI. The SDI page is displayed. 
 
2 Set the M1 Port Type and M2 Port Type (SDI or ASI). 
3 Select Enable VII/AFD Output in SDI, Enable VBI Output in SDI, Enable DPI 
Output in SDI, and/or Enable EIA708 Output in SDI to enable the VII (video 
index)/AFD, VBI, DPI, and/or EIA-708 outputs in SDI. 
4 In the SDI Audio Group Setup section, you...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
174 78-4021470-01 Rev J 
Setting up Services to be Decoded by the D9854 Receiver 
1 From the user interface of the D9854, click Audio & Video > Other Outputs > 
Decode Enables. The Decode Enables page is displayed. 
 
2 Select the services to be decoded by the receiver. Select/de-select Enable Decode 
Engine to select/de-select all the services in the list. 
3 Click Apply. 
  

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 175 
 
Configuring Transport Stream Information 
Configuring the ASI Output 
1 From the user interface of the D9854, click Transport Stream > Transport 
Handling > ASI Output. The ASI Output page is displayed. 
Note: After you make any changes, a successfully updated (session open) 
message appears. The changes are displayed, but not saved. You must click 
Apply to save and apply the changes. 
 
Note: Any changes made to the ASI DPM...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
176 78-4021470-01 Rev J 
3 If the Rate Control was set to User, set the maximum output bit rate in the User 
Rate field. This setting is used when the signal source is RF or ASI and allows 
you to set the output bit rate to a value expected by equipment connected to the 
ASI output. 
You can enter a range from 0 to 206 Mbps. 
Note: Output data may be lost if this bit rate is set to a value less than the actual 
signal bit rate. 
4 Select the DPM Output...