Cisco D9854i Manual

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 177 
 
Output Mode Description 
Full DPM Control The output will be generated according to the DPM 
settings. This is a manual control setting. 
5 In Descrambled drop-down, select whether the output will be descrambled if 
the input is scrambled. The following table describes the available options: 
Descramble Description 
Scrambled The output channel will remain scrambled even if the PE is 
authorized and can descramble the channel....

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
178 78-4021470-01 Rev J 
Configuring the DPM ASI Details 
The following procedure defines all the available fields. For a typical setup of the 
DPM, see Typical set up for Digital Program Mapping (DPM) (on page 192). 
Note: After you make any changes, a successfully updated (session open) message 
appears. The changes are displayed, but not saved. You must click Apply to save 
and apply the changes. 
1 From the user interface of the D9854, click Transport...

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 179 
 
 
6 Enter the Output Channel # you want to map to the input channel (Input 
Channel #). This value is only used if the PE Action was set to Map. You can 
enter a range from 1 to 65535. 
7 Enter the Output PMT PID you want to map to the Input PMT PID. 
8 In the PE PID MAP section, you can select an existing PID mapping entry you 
want to modify or click Add Row to create a new entry.  
9 The Input Stream indicates the input...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
180 78-4021470-01 Rev J 
17 In the DPM Program Entry Setup section, each PE output can be synchronized 
to its input according to one of the four output modes. Select the program entry 
you want to synchronize and then click Resynchronize or click Resynchronize 
All to synchronize the inputs to the outputs according to the service assignments 
only.  
Note: The resynchronization will not synchronize the inputs if there is no valid 
input on the PE or if...

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 181 
 
Map Mode Description 
Svc ID The elementary PIDs are not changed. Channels are remapped by 
changing their PSI references. When this mode is selected, PE 
detailed PID mapping in the PID menu are ignored. 
Svc ID & PID Channels and the elementary service PIDs can be mapped in the 
DPM PE PID MAP window. 
22 Select the Duplication Method for how to handle duplicate programs. This 
setting is only used if Remapping Mode is set to...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
182 78-4021470-01 Rev J 
Svc ID Description 
Valid Ch Only transmits the PSI tables for the mapped program if the 
program exists on the input stream. 
All Ch Transmits the PSI tables for the mapped program even if the 
program does not exist in the input stream.  
All Ch is only valid if the PAT, NIT, SDT and PMT are set to 
Regenerate. 
25 If PSI Table Output Option is set to Ctrl by Table, select the regeneration rate for 
those PSI tables being...

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 183 
 
 
29 Select the tables which will be passed, dropped, regenerated or passed with rate 
control (PwRC) from the ASI Output. The CDT table is different from the other 
tables listed. For more information on the table options, see PSI Table Settings 
(on page 109). 
30 Click OK. 
31 Click Apply. 
If a conflict occurs, a detailed error message appears at the top of the page. You 
must resolve the conflict and then click Apply to save...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
184 78-4021470-01 Rev J 
  
Configuring the MPEGoIP Output 
1 From the user interface of the D9854, click Transport Stream > Transport 
Handling > MPEG over IP Output. The MPEG over IP Output page is 
displayed. 
Note: After you make any changes, a successfully updated (session open) 
message appears. The changes are displayed, but not saved. You must click 
Apply to save and apply the changes. 
 
Note: Any changes made to the MOIP DPM values will...

 
 
 Configuring Transport Stream Information 
 
78-4021470-01 Rev J 185 
 
Note: Output data will be partially lost if the user-selected bit rate is set to a 
value that is less than the actual signal bit rate. This allows you to set the output 
bit rate to a value expected by equipment connected to the MPEGoIP output. 
You can enter a range from 0 to 206 Mbps.  
4 Select the DPM Output Mode. The following table describes each mode:  
Output Mode Description 
No Output No MPEGoIP output will be...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
186 78-4021470-01 Rev J 
8 Enter the unicast (valid host IP only) or multicast Destination IP Address 
(224.0.0.0 to 239.255.255.255). 
9 Select the Destination Port number (1 to 65535). 
Note: If you selected RTP as the Protocol, you must select an even destination 
port number. 
10 Enter the Source UDP Port number (1 to 65535). 
11 In the Send SAP drop-down list, select whether to send Session Announcement 
Protocol messages (Yes or No). 
12 Select...