Christie Projector J Series 2.0, 2.4, And 3.0kW User Manual

Section 4: Web User Interface
J Series 2.0, 2.4, and 3.0kW User Manual4-7020-100707-01  Rev. 1  (10/2011)
The following table describes each area found in the Admin window. See Figure 4-10.
Uploading a Logo File or Gamma File
Important: The projector must be powered on to enable the Upload drop-down list.
1. Click the Upload Browse button to open the Select file window. 
2. Locate and select the file you wish to upload from a Network drive location or from your hard drive. 
3. Select the file type (Logo...

4-8J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   10-2011
Section 4: Web User Interface
4. Click the Upload button to display the Logo Upload window.
a. Enter a descriptive name in the Display Name field.
b. Click the Upload button to display the Gamma Upload window. Click Yes or No to confirm or cancel 
the upload respectively.
An Upload in Progress window appears. 
Creating a Backup File
1. Select a file type (All, Preferences, Configuration, Channels, or Users) from the Backup...

Section 4: Web User Interface
J Series 2.0, 2.4, and 3.0kW User Manual4-9020-100707-01  Rev. 1  (10/2011)
Creating a User Name and Password
1. Click Add User to open the Add User window. See Figure 4-11.
2. Type your username and password in the User name and 
Password fields respectively.
3. Re-type your password in the Re-type Password field.
4. Click Ok to save.
Change Password
1. Select the user whose password you wish to change from the 
Users window. See Figure 4-12.
2. Click Change Password to...

4-10J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   10-2011
Section 4: Web User Interface
TO ADD A SCHEDULED EVENT
1. Click Add to open the RTE Wizard.
2. Select the Scheduled Event tab. 
NOTE: The scheduled tab is always selected by default on add.
FIGURE 4-14 SCHEDULED EVENT WINDOW
3. Select the frequency option for the event by selecting either Once, Daily, Weekly, or Monthly. NOTE: 
End Date is enabled when Daily, Weekly or Monthly repeat options are selected.
4. Click within the...

Section 4: Web User Interface
J Series 2.0, 2.4, and 3.0kW User Manual4-11020-100707-01  Rev. 1  (10/2011)
• Click the Test button to test the entered command string. NOTE: If the test passed or failed, a green or 
red icon appears to the right side of the Test button as shown in Figure 4-16 Test Buttons.
FIGURE 4-16 TEST BUTTONS
10. Click Finish to create the added event. NOTES 1) The added event appears in the RTE Listing window. 
See Figure 4-17 RTE Listing Window Example. 
2) To activate or...

4-12J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   10-2011
Section 4: Web User Interface
To Add a GPIO Event
1. Click Add to open the RTE Wizard.
2. Select the GPIO Event tab.
3. For the GPIO Event option define the Input 
Condition field as required. The Input 
Condition field contains 7 blocks which refer to 
the 7 I/O pins on the GPIO connector. Pin 1 = 
+12V and Pin 5 = Ground are not included or 
changed. 
2) Clicking a block toggles between H, 
L, and X as shown in Figure 4-19 GPIO...

Section 4: Web User Interface
J Series 2.0, 2.4, and 3.0kW User Manual4-13020-100707-01  Rev. 1  (10/2011)
TO ADD A SERIAL COMMAND
1. Enter a serial command in the Serial Command 
field. 
NOTE:  For Serial Commands refer to the M 
Series Serial Commands Technical Reference 
Information P/N 020-100224-xx, available at the 
Christie Website.
2. Click Send to add the serial command. See Figure 
4-22.   
4.3.8 About Tabbed Page
Provides information about the projector software 
version, model, serial number,...

J Series 2.0, 2.4, and 3.0kW User Manual5-1020-100707-01  Rev. 1  (10-2011)
 
5 Maintenance
Installers, service trained operators and all other users must maintain a safe operating environment at all
times. Read through this section in its entirety and understand all warnings and precautions before
attempting to operate this projector. 
5.1 Projector Location
Operate the projector in an environment that meets the operating range specifications in Section 6 Specifica-
tions. Do not operate the projector...

5-2J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Section 5: Maintenance
1. TURN THE LAMP OFF
Press the power to switch the lamp off. Allow the cooling fans to stop automatically (within 5 minutes) before 
proceeding with step 2. 
NOTE: This wait period is required to allow the lamp to sufficiently cool before 
handling.
2. UNPLUG THE PROJECTOR
When the cooling fans have stopped, turn the main switch of the projector off, then unplug the projector.
 Always power down and unplug...