Christie Projector J Series 2.0, 2.4, And 3.0kW User Manual

Section 3: Operation
J Series 2.0, 2.4, and 3.0kW User Manual3-45020-100707-01  Rev. 1  (10-2011)
•Show Blending Overlap turns your defined blend width area to solid grey so that, if needed, simply 
overlapping the grey bars can seamlessly align two adjacent images. Toggle the Show Blending Overlap off 
to reactivate the blend effect. 
NOTE: Blending Overlap appears as Reserved when Christie TWIST is 
installed.
Other Functions
For convenience, the Edge Blending submenu also includes related options for...

3-46J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Section 3: Operation
COLOR ADJUSTMENTS BY X/Y - Submenu
Enter known x/y coordinates from the chromaticity graph
NOTES: 1) For defining or changing a User 1, 2, 3, or 4 color 
performance or “gamut”. Sometimes known as Comprehen-
sive Color Adjustment™. 
2) Factory-defined primary color 
levels, which ensure a specific color performance from 
projector-to-projector, can be calibrated in the Service menu 
only. The factory...

Section 3: Operation
J Series 2.0, 2.4, and 3.0kW User Manual3-47020-100707-01  Rev. 1  (10-2011)
FIGURE 3-38 CIE 1931 CHROMATICITY DIAGRAM
NOTE: Keep new x,y coordinates within the original color gamut triangle shown here.
COLOR SATURATION - Submenu
Adjust color slide bars and judge image color by eye or meter. A user-defined color “adjustment” can be 
applied by selecting it in the Advanced Image Settings menu (select ‘Color Adjustment’).
Use this submenu if you do not have specific color coordinates...

3-48J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Section 3: Operation
Procedure
NOTES: 1) Adjust white levels before adjusting black levels. 2) The zones in BLB menu correspond to the Edge 
Blend zones. If a given Edge Blend zone width is set to 0 (i.e. no blend on that side) then the corresponding 
BLB zone is disabled. It only becomes accessible when that Edge Blend zone is active.
1. Start with two projectors. In the Black Level Blending submenu, enable black blending by...

Section 3: Operation
J Series 2.0, 2.4, and 3.0kW User Manual3-49020-100707-01  Rev. 1  (10-2011)
On each projector you must set the following:
The tiling array size - set the total rows and total columns. This setting will be the same on all the projec-
tors in the array. 
The relative location of the projector within the array - set the row number and column number for each 
projector
Enable Tiling - Tiling can be enabled or disabled without losing any of the above settings.
The features that act...

3-50J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Section 3: Operation
• INPUT LEVEL DETECTOR
The Input Level Detector check box enables specific thresholds for blacks and whites. Input levels that fall 
below a specified level value (see below) are displayed as black, and all others are displayed as white. To use:
1. Enable Input Level Detector and display a continuous greyscale.
2. Set Level Detector Threshold to near black (such as 200).
3. Adjust Offsets to minimize area...

Section 3: Operation
J Series 2.0, 2.4, and 3.0kW User Manual3-51020-100707-01  Rev. 1  (10-2011)
3.9 Lamp Menu
LAMP MODE
Determines how the lamp power and 
intensity are controlled. If Maximum 
Brightness is selected, the lamp burns 
as brightly as possible. Select Constant 
Intensity mode to maintain a specific 
brightness level over time. As the lamp 
ages, the projector will increase power 
as needed, to closely maintain the required output from the lamp. Select Constant Power to specify the power...

3-52J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Section 3: Operation
CHANGE LAMP - Submenu
Initiates the lamp change process and allows the serial number of the new lamp to be entered.
Lamp serial numbers are used for keeping statistics on each lamp. Entering of serial numbers is optional, but is 
recommended. 
When using this function, the statistics from the previous lamp are archived, and statistics for the new lamp are 
tracked. If this function is not used, statistics...

Section 3: Operation
J Series 2.0, 2.4, and 3.0kW User Manual3-53020-100707-01  Rev. 1  (10-2011)
PIP WINDOWS OPTIONS - Submenu 
•PIP POSITION PRESETS 
Select a preset location and size of the PIP window. While in split screen mode, several channel controls that 
resize image will be disabled. These controls are size, H-Position and V-Position.
•PIP WINDOW SIZE 
Sets the width of the PIP window in pixels. The active portion of the input signal, as determined by blanking 
controls, will be scaled to fit...

3-54J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Section 3: Operation
HDMI OUTPUT LOOP SOURCE
Configure the HDMI output options. 
Select Direct Loop to directly pass-through the HDMI input signals (from the same Twin HDMI Input Card). 
The Input1 signal is looped to Output1 and the Input2 is looped to Output2. 
Select Main/Secondary Loop to loop the Main & secondary video to the outputs (regardless of which card 
these signal originate from). The Main video signal is looped...