Christie Projector J Series 2.0, 2.4, And 3.0kW User Manual

Section 3: Operation
J Series 2.0, 2.4, and 3.0kW User Manual3-55020-100707-01  Rev. 1  (10-2011)
Preliminary Calibration
All primary colors in the projector are precisely set to pre-established values to ensure that overall color 
performance is optimized and is as accurate as possible. Lighting and other environmental factors may slightly 
change how these colors appear on your screen. While the change is negligible in most cases, you may prefer 
to recover the originally intended color performance...

3-56J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Section 3: Operation
• Display the Color Adjustments by X,Y menus for all projectors. Each menu shows the x/y coordinates 
defining the “Max Drives” color gamut for this projector. 
NOTE: The values shown in one (any) of the 
displays. Use the “Copy From” function to copy them into a “User” gamut in one projector. 
4. In each projector, select a “User” color adjustment (1-4) to enable Color Adjustments by X,Y changes. Then...

Section 3: Operation
J Series 2.0, 2.4, and 3.0kW User Manual3-57020-100707-01  Rev. 1  (10-2011)
• To match reds, decrease “Red X” until full 
field red screens match.
• To match greens, decrease “Green Y” until 
full field green screens match.
• To match blues, increase both “Blue X” and 
“Blue Y” until full field blue screens match.
NOTE: For speed, enable the “Auto Color 
Enable” check box. Each color coordinate you 
select will then automatically trigger a full 
field display of the corresponding...

3-58J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Section 3: Operation
3.13 Remote Control of the Projector
As an alternative to using a keypad, most projector functions can be controlled remotely, typically at a 
controller such as a PC, via a web interface.
VIA ASCII MESSAGING — Connect a serial link between your controller and the RS-232 or RS-422 port 
(recommended), or open an Ethernet socket (i.e., Telnet) between your controller and the valid projector 
address. Valid...

J Series 2.0, 2.4, and 3.0kW User Manual4-1020-100707-01  Rev. 1   10-2011
4 Web User Interface
4.1 Logging On
IMPORTANT!  Before logging on to the system, ensure that you select the appropriate language 
required. Your language selection only affects the web user interface. The language used by the 
projector on-screen display (OSD) is not affected. See Figure 4-1. 
1. Open your web browser and type the IP address (in the address bar) assigned to your projector.
2. Select the appropriate language from...

4-2J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   10-2011
Section 4: Web User Interface
The following table describes each area found in the Main window. See Figure 4-3.
4.2 Navigating the Web User Interface
It is not recommended that you use the web browser navigation functionality (i.e. the Back and Forward 
functions) as this will cause you to lose your web connection. It is recommended that you navigate using the 
application interface and related functionality detailed in this...

Section 4: Web User Interface
J Series 2.0, 2.4, and 3.0kW User Manual4-3020-100707-01  Rev. 1  (10/2011)
4.3 Basic Operation
This section discusses the primary tabs located along the top of the application window. Each primary tab also 
has related secondary tabs which are located along the bottom of each tabbed page as follows:
• Main
• General
• Status
• Lens
• Tools
• Virtual OSD
• Admin
• System
• Users
• Advanced
•RTE
• Serial
• About
• Version
• License
4.3.1 Main Tabbed Page - General
Under the...

4-4J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   10-2011
Section 4: Web User Interface
4.3.3 Main Tabbed Page - Lens 
Under the Main tabbed page, select the Lens secondary tab to define your adjustment settings for the lens. For 
detailed information, refer to Section 3 Operation.
4.3.4 Tools Tabbed Page - Virtual OSD 
Under the Tools tabbed page, select the Virtual OSD secondary tab to access to the virtual OSD page. See 
Figure 4-6.
FIGURE 4-6 TOOLS WINDOW
 The following table...

Section 4: Web User Interface
J Series 2.0, 2.4, and 3.0kW User Manual4-5020-100707-01  Rev. 1  (10/2011)
Virtual OSD Menu
By selecting an option from a menu, its associated window 
appears, showing related information and input fields. To 
return to the previous menu, click the menu title bar (see 
Figure 4-7). 
To return to a previous menu, click on the current menu title 
bar or press ESC. 
NOTE: It is recommended to click the 
Maximize button to view the full screen size.
There are various types of...

4-6J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   10-2011
Section 4: Web User Interface
SELECTING A OPTION FROM A DROP-DOWN LIST
1. Click the option drop-down arrow to open the drop-down list. 
2. Locate and select the desired option.
FIGURE 4-9 TYPES OF MENU ELEMENTS
SELECTING OR CLEARING A CHECK BOX
To select or clear a check box, click the check box with your mouse pointer. This enables or clears the option 
respectively.
4.3.5 Admin Tabbed Page - System
Under the Admin tabbed page,...