Canon scanner imageFORMULA DRX10C User Manual

							8-23
Chapter 8   ISIS/TWAIN Driver Settings
Code 39 
Detect Code 39 barcodes. 
[Enable]
Detect and read Code 39 barcodes. 
[Full Ascii]
Read barcodes in Full ASCII Code. 
[Checksum]
Read the checksum included in barcodes.
[Output Checksum]
This check box is enabled when [Checksum] is selected, 
and outputs the read checksum.
[Output ST/SP]
Select this check box to output Start and Stop codes.
Codabar
Detect Codabar barcodes. 
[Enable]
Detect and read Codabar barcodes. 
[Checksum]
Read the checksum included in barcodes.
[Output Checksum]
This check box is enabled when [Checksum] is selected, 
and outputs the read checksum. [Output ST/SP]
Output Start and Stop codes included in barcodes. 
[Method]
Select the checksum calculation method.
Code 128
Detect Code 128 barcodes. 
[Enable] Check Box
Select this check box to detect and read Code 128 
barcodes.
ITF
Detect ITF barcodes (including industrial 2 of 5).
[Enable]
Detect and read ITF barcodes. 
[Checksum]
Read the checksum included in barcodes.
[Output Checksum]
This check box is enabled when [Checksum] is selected, 
and outputs the read checksum.  
						

							8-24
Chapter 8   ISIS/TWAIN Driver Settings
UPC
Detect UPC-A/UPC-E barcodes. 
[Enable] Check Box
Detect and read UPC-A/UPC-E barcodes. 
[Addon]
Set how to handle addon codes included in barcodes.
Off: Ignore addon codes.
On: Read addon codes.
Auto: Detect and read addon codes automatically. 
[Checksum]
This check box is enabled when [Checksum] is selected, 
and outputs the read checksum. 
[Output Header]
Select this check box to output header codes.
Hint
 To detect barcodes with and without add-on codes at the 
same time, select [Auto] for the addon setting before 
scanning.
 When the barcode type is unknown, enable detection of all 
types (Auto Detect), and deselect the Checksum boxes before 
scanning.
[Pre Imprinter] and [Post Imprinter] Tab 
Sheets
The [Pre Imprinter] tab sheet is displayed when an optional 
pre-imprinter unit is installed, and allows you to imprint any 
character string or counter on to documents before scanning.  
						

							8-25
Chapter 8   ISIS/TWAIN Driver Settings
The [Post Imprinter] tab sheet allows you to imprint/add any 
character string or counter on scanned documents. 
The [Imprinter] check box is enabled only if the optional pre-
imprinter unit is installed.
■[Pre Imprinter] and [Post Imprinter] Tab Sheet 
Settings
You can configure the following settings on the [Pre 
Imprinter] and [Post Imprinter] tab sheets. 
Check Boxes
[Imprinter] Check Box
Configure settings for imprinting any character string or 
counter on scanned documents. 
IMPORTANT
 Confirm that an ink cartridge is installed in the scanner before 
you use the imprinter function. “ImprinterError” is displayed on 
the scanner LCD if scanning is performed without the ink 
cartridge.
 Pre-imprinter printing is only available when the scanner’s 
Double-Feed Retry function is set to OFF.
[Addon] Check Box ([Post Imprinter] tab sheet only)
Configure settings for adding any character string or 
counter on scanned images. 
Text
Enter any character string to be imprinted or added.
Hint
The following characters can be entered.
 Numerals: 0 to 9
 Alphabetic characters: A to Z and a to z
 Symbols: ! # $ % &( ) * + - . , / : ; < > =?@[ ] { } ~ ` \
Enter special text such as counters, dates and arrows from 
the list that appears by clicking the [Special] button.
The selected abbreviation is inserted into the text string.
[Single counter] abbreviation: 
Print/add one 9-digit counter.
[Double counter] abbreviation: 
Print/add two 9-digit counters.
[Single counter with number of characters] 
abbreviation: 
A dialog box appears in which to specify the number of 
characters of the single counter. A counter of the specified 
number of characters will be imprinted or added on 
scanned images. 
						

							8-26
Chapter 8   ISIS/TWAIN Driver Settings
[Double counter with number of characters] 
abbreviation: 
A dialog box appears in which to specify the number of 
characters of the double counter. A counter of the specified 
number of characters will be imprinted or added on 
scanned images.
[Current time] abbreviation: 
Imprint/add the time of scanning using 8 digits in 24-hour 
format.
[Date (Month/Day/Year)] abbreviation: 
Imprint/add the date of scanning using 10 digits in Month/
Day/Year format.
[Date (Day/Month/Year)] abbreviation: 
Imprint/add the date of scanning using 10 digits in Day/
Month/Year format.
[Date (Year/Month/Day)] abbreviation: 
Imprint/add the date of scanning using 10 digits in Year/
Month/Day/format.
[Up arrow] abbreviation: 
Imprint/add an up arrow (K).
[Down arrow] abbreviation: 
Imprint/add a down arrow (L).
[Left arrow] abbreviation: 
Imprint/add a left arrow ().
[Right arrow] abbreviation: 
Imprint/add a right arrow (J).
IMPORTANT
 Special text can only be entered for one type of counter. If you 
enter two types of counter and click [OK], an error message is 
displayed.  A maximum of 32 characters can be imprinted or added, but 
the number of characters you can enter may be limited by the 
font size. 
If the number of characters entered exceeds the limit, an error 
message is displayed when you click [OK]. 
Print Position
Specify the position for printing.
[Horizontal Offset]
Specify the horizontal offset by selecting a radio button 
compatible with the ink outlet. 
 Pre Imprinter
 Post Imprinter
Hint
The offset is a position from the left of the feeder inlet. 
[Vertical Offset]
Enter the distance from the top edge of the page. (0 to 
19.69) (0 to 500 mm)
Hint
The input range changes if Long Document Mode is enabled. 
The input range is (0 to 39.37) (0 to 1000 mm) when Long 
Document Mode is set to [ON1], and (0 to 118.11) (0 to 3000 
mm) when it is set to [ON2]. 
						

							8-27
Chapter 8   ISIS/TWAIN Driver Settings
Orientation
Specify the orientation of characters to be imprinted or 
added.
Hint
Text orientation relative to the feeding direction is as follows.
Imprinter Font
Specify the font size of characters to be imprinted or 
added.
[Expand character spacing]
Select this check box to expand the spacing between 
printed or added characters.
Addon Type
Specify the method in which text is added on to the image.
[Black on White]
Add black text on to a white background.[White on Black]
Add white text on to a black background.
[Black on Image]
Add black text on to an image.
[Counter] button
Open the [Counter] dialog box, and configure counter 
settings.
■[Counter] Dialog Box
Make settings for add-on counters.
First Counter
This is the current setting for the single counter, or for the 
first counter if double counters are selected.
Hint
The setting can be changed in the [Counter] dialog box.
Second Counter
This is the current setting for the single counter, or for the 
second counter if double counters are selected.
Hint
The setting can be changed in the [Counter] dialog box.
Orientation0 degrees 90 degrees 180 degrees 270 degrees
Print 
						

							8-28
Chapter 8   ISIS/TWAIN Driver Settings
■[First Counter] and [Second Counter] Dialog 
Boxes
Make settings for add-on counters.
[Start Value]
Enter the start value for the counter.
[Increment]
Enter the increment value for the counter. The counter 
increases by the value entered here.
[Increment Trigger]
Specifies the type of event that triggers a counter 
increment.
[New File] (ISIS driver only)
The counter increases when a batch separation occurs 
according to the Batch Separation settings on the [Others] 
tab sheet. (See “Batch Separation” on p. 8-20.)
IMPORTANT
The counter for the imprinter does not increase when [Patch 
code] is selected for [Batch Separation].
[Every Page]
Increments once per page.
[None]
No counting up.
[Reset Value]
Select the initial value when the counter is reset.
[Reset Trigger]
Select the trigger for resetting the counter.
[New File] (ISIS driver only)
The counter is reset when a batch separation occurs 
according to the Batch Separation settings on the [Others] 
tab sheet. (See “Batch Separation” on p. 8-20.)
IMPORTANT
The counter for the imprinter does not reset when [Patch code] 
is selected for [Batch Separation].
[Every Page]
Resets the counter once per page.
[None]
No counter reset occurs. 
						

							Chapter 9   Job Registration Tool Settings
1. Before Use ....................................................... 9-2
Job Function..........................................................9-2
Starting the Job Registration Tool .........................9-2
2. Job Registration Tool ....................................... 9-3
3. Settings Dialog Boxes...................................... 9-5
[New/Editing] Dialog Box.......................................9-5
[Admin] Dialog Box................................................9-8 
						

							9-2
Chapter 9   Job Registration Tool Settings
1.Before Use
The Job Registration Tool is an application for registering jobs that can be executed from the [Job] key on the control panel. This 
chapter describes the settings for the Job Registration Tool. For details on the Job Function, see “About the Job Function” (see 
p. 3-14).
Job Function
The job function is for using the [Job] key on the control panel 
to select and execute jobs registered by Job Registration Tool, 
and allows you to execute scanning without using a scanning 
application. 
Hint
 Job registration stores scanning condition settings, image file 
format selection, save destination and image data processing 
settings for each job to be used with the Job Function. 
 Up to 99 jobs can be registered with the Job Registration Tool. 
Starting the Job Registration Tool
Follow the procedure below to start the Job Registration Tool. 
1.Click the [Start] button, and then click [All Programs] 
- [Canon DR-X10C] - [Job Registration Tool].
 
The Job Registration Tool starts. 
						

							9-3
Chapter 9   Job Registration Tool Settings
2.Job Registration Tool
The Job Registration Tool consists of the main window below and the [New/Editing] and [Admin] dialog boxes. For details on the 
dialog boxes, see the description of each dialog box.
Menu Bar
[Edit] Menu
Select a job from the job list, and register a new job or edit, 
copy, or delete the job. (See “[New/Editing] Dialog Box” 
on p. 9-5.)
Hint
 If you select a registered job, [Copy] and [Delete] are enabled. 
Selecting [Copy] displays the following dialog box. Specify the 
job number to copy to and job title, and click the [OK] button to 
copy the job to the specified job number. 
 Selecting [Delete] displays a confirmation message. 
 The items of the [Edit] menu are also displayed in a submenu 
when you right-click a job. 
[Admin] Menu
Open the [Admin] dialog box to configure settings for 
monitoring the storage folder for images and backing up 
job data. (See “[Admin] Dialog Box” on p. 9-8.)
[Help] Menu
Display the help and version of the Job Registration Tool. 
						

							9-4
Chapter 9   Job Registration Tool Settings
Job List
Displays the job numbers (01 to 99) and job titles. 
Job Information
Displays the information for the job selected in the job list. 
[Close] Button
Ends the Job Registration Tool.