Canon scanner imageFORMULA DRG1130 User Manual

5-10
Chapter 5   Maintenance
■Removing and Reinstalling the Pickup Roller1.
Open the upper unit smoothly. (See “Opening the 
Upper Unit” on p. 5-3.)
2.
Open the roller cover.
3.
Open the roller holder.
Hint
The roller holder returns to its original position when released.
4.
Remove the pickup roller, and set a clean pickup 
roller or a replacement pickup roller. 
IMPORTANT
Install the Pickup Roller so that the side with the gear is on the 
left.
5.
Close the roller cover. Make sure to hear a latching...

5-11
Chapter 5   Maintenance
■Removing and Reinstalling the Feed Roller1.
Open the upper unit smoothly. (See “Opening the 
Upper Unit” on p. 5-3.) 
2.
Open the roller cover.
3.
Pull the roller lock lever down.
4.
Slide the feed roller to the right, and then pull them 
towards you.
5.
Remove the feed roller.
6.
Place the new feed roller on the pin.
7.
Put the feed roller in place (1), and align the notch in 
the roller’s axle with the shaft on the scanner (2).
(1)
(2) 

5-12
Chapter 5   Maintenance
8.
Push the roller lock lever up to lock the feed roller.
9.
Close the roller cover. Make sure to hear a latching 
sound and that it is securely returned to its original 
position.
IMPORTANT
Failure to firmly close the roller cover may cause a feed error. 
Always be sure to check that the roller cover is closed.
10.
Smoothly close the upper unit. (See “Closing the 
Upper Unit” on p. 5-3.)
■Removing and Reinstalling the Retard Roller1.
Open the upper unit smoothly. (See...

5-13
Chapter 5   Maintenance
4.
Remove the retard roller, and set a clean retard roller 
or a replacement retard roller. CAUTION
The metal sections of the roller can become extremely hot after 
continuous use. Do not directly touch the metal. Wait until the roller 
has thoroughly cooled before replacing it.5.
Align the roller cutout to the axle on the device, and 
slide the roller securing lever in the direction of the 
arrow. 
6.
Pull the roller lock lever down to lock the retard roller 
in place.
7....

5-14
Chapter 5   Maintenance
3.
Detaching and attaching the separation pad (retard roller cover)
When replacing the separation pad, perform the following steps to detach it from and attach it to the unit. When to replace the separation pad (retard 
roller cover)The separation pads are consumables that must be replaced 
after feeding about every 6,000,000 pages.
A worn separation pad is no longer able to correctly feed a 
document and can cause paper jams. If documents no longer 
feed correctly as...

5-15
Chapter 5   Maintenance
■Replacement parts
Product Name: Separation pad
Product Code: 8262B002 

5-16
Chapter 5   Maintenance
4.
Imprinter Ink Cartridge Replacement and Cleaning
When the optional imprinter is used, printing will become faint or nonexistent when the ink is depleted. It is recommended to keep 
a spare ink cartridge available.About the ImprinterThe ink cartridge for the imprinter that prints on scanned 
documents is installed in the following location.■Preparing an Ink Cartridge
Use one of the following red, blue or green HP ink 
cartridges. For details, contact your local authorized...

5-17
Chapter 5   Maintenance
3.
Open the imprinter cover until it makes contact with 
the eject tray.
Hint
Perform the steps that follow with the imprinter cover fully open.
4.
Pull the lock lever outward (1) to release the ink 
cartridge lock (2).
5.
Remove the ink cartridge.
6.
Peel off the seal covering the nozzles of a new ink 
cartridge.
CAUTION
Peel off the seal covering the nozzles of a cartridge only if you 
are going to use it immediately. Also, avoid touching the metal 
contacts or nozzles of...

5-18
Chapter 5   Maintenance
8.
Push the ink cartridge as indicated by the arrow until 
it clicks into place.
9.
Adjust the carriage position by moving it left or right, 
then make sure you can feel it click in. (See 
“Specifying the Printing Position” on p. 5-18.)
Hint
If you do not feel it click in, the carriage is not aligned correctly 
with a positioning hole. Always move the carriage to a position 
where it clicks in.
10.
Close the imprinter cover.
With your finger, push in the area of the imprinter...

5-19
Chapter 5   Maintenance
1.
Roughly align the right edge of the lock lever with the 
desired printing position.
Hint
The position of the right edge of the lock lever indicates the 
current printing position.
2.
Finely adjust the carriage position by moving it left or 
right, then make sure you can feel it click in.
Hint
• If you do not feel it click in, the carriage is not aligned correctly 
with a positioning hole. Always move the carriage to a position 
where it clicks in.
• The imprinter cover...