Canon scanner imageFORMULA DRG1130 User Manual

3-22
Chapter 3   Basic Operation
6.
Handling Interruptions in Scanning
If an error occurs during scanning, document feeding will be interrupted. This section describes how to handle such occurrences.Check Error Message on Control PanelWhen document feeding is interrupted, an error message will 
appear on the display panel.■When a paper jam is detected
■When a skewed document is detected
■When a staple is detected
■When a double feed is detected (Rapid 
Recovery System disabled)
■When a double feed is...

3-23
Chapter 3   Basic Operation
4.
Close the upper unit gently. Then press it at both 
ends to make sure it is fully closed.
(See “Closing the Upper Unit” on p. 5-3)
5.
Check to verify the last saved image, and perform 
rescanning.
IMPORTANT
• Even if a document is ejected onto the eject tray, the scanned 
image of the document may not be saved. Before rescanning, 
always check the last saved image.
• Before rescanning, straighten documents that were detected 
as skewed.
• Before rescanning, remove any...

3-24
Chapter 3   Basic Operation
When detecting double feeds by ultrasonic sensorsReturn the document pages ejected as a result of double-
feed detection to the top of the document stack yet to be 
scanned, and resume scanning.
■When the Rapid Recovery System is Enabled• When the Rapid Recovery System is enabled, scanning pauses 
when a double feed is detected, and the following error message 
is displayed.1.
Check the rejected document page(s).
Hint
• If attached paper, such as a label on the document...

Chapter 4   Other Functions
1. Function Description ........................................ 4-2
2. User Mode ....................................................... 4-4User Mode Operating Procedure ..........................4-43. User Mode Functions....................................... 4-6 

4-2
Chapter 4   Other Functions
1.
Function Description
The function for counting the documents before scanning is described below.■Count-Only Mode
Counts the number of loaded document sheets by simply 
feeding them through the scanner.
Hint
The Count-Only mode is executed by the Count Only key on the 
control panel, and can be used to count document sheets even 
when no computer is connected.
1.
Place the documents into the tray.
2.
Press the Count Only key on the control panel.
The Count Only key...

4-3
Chapter 4   Other Functions
3.
Press the Start Key to start scanning.
“Verifying…” is displayed.
Hint
If the specified count is exceeded while scanning, or if the 
scanned count does not reach the specified count when 
scanning is finished, an error is displayed.
The specified count is exceeded while scanning
Scanning finishes without reaching the specified count 

4-4
Chapter 4   Other Functions
2.
User Mode
The User Mode provides the user with the capability to change certain scanner functions.User Mode Operating ProcedureUser Mode operations are controlled by the following 
procedure.
Hint
Operating procedures differ according to User Mode function. For 
details, refer to the indicated pages.1.
Press the Menu key on  the control panel.
The User Mode is activated.
2.
Press the [ ] and [ ] keys to select the User Mode 
function.
The User Mode functions are...

4-5
Chapter 4   Other Functions
3.
Press [Enter].
The current setting is indicated with blinking square 
brackets [ ].
4.
Press the [ ] or [ ] key to select [ON2], [ON1] or 
[OFF], and press [Enter] to accept the selection.
5.
Press the [Stop] key to exit the User Mode.
Enter Key 

4-6
Chapter 4   Other Functions
3.
User Mode Functions
The following functions are available in the User Mode.■Separation Mode Setting
If double feeding or a paper jam occurs, change to 
Separation Mode.
HI: Use if friction between sheets is great, and you are 
feeding documents that are difficult to separate.
Normal: Use this setting normally.
LO: Use when feeding fine documents.
IMPORTANT
On [HI], as the separation power is great, the paper may tear. If 
this happens, use [Normal] or [LO].
■Buzzer...

4-7
Chapter 4   Other Functions
■Long Document Mode Setting
You can enable this mode to scan document pages up to 
3,000 mm (118.1) long when the Auto Detection page 
size setting is selected. (See “Long Document Mode 
Setting” on p. 3-3.)
ON2: Automatically detects page sizes when scanning 
documents up to 3,000 mm (118.1) long.
ON1: Automatically detects page sizes when scanning 
documents up to 1,000 mm (39.4) long.
OFF: Automatically detects page sizes when scanning 
documents up to 432 mm (17)...