Canon scanner imageFORMULA DRG1130 User Manual

3-2
Chapter 3   Basic Operation
1.
Documents
The scanner can scan documents ranging in size from business cards and checks to 11 × 17/A3 size. The size and type of paper 
that can be fed depends on the feeding method.Acceptable DocumentsThe scanner can feed the following document sizes.
Size
Width: 50.8 mm to 305 mm (2 to 12)
Length: 70 mm to 432 mm (2.8 to 17) (without using the 
Long Document Mode) 
70 mm to 1,000 mm (2.8 to 39.4) (using [ON1] in the 
Long Document Mode) 
70 mm to 3,000 mm (2.8 to...

3-3
Chapter 3   Basic Operation
• Note that scanning the following types of documents can 
cause a paper jam or malfunction. To scan such a document, 
make a photocopy of the document and then scan the 
photocopy. 
• To scan bound multi-page documents such as invoice 
booklets, place the bound edge against the feeder inlet and 
scan by manual feeding. 
• To use the Long Document Mode, feed document pages 
manually, one after another.
Document Feeder Capacity
Up to 500 sheets of high grade paper or paper...

3-4
Chapter 3   Basic Operation
3.
Confirm your settings.
[ON2]: When the [Match original size] or [Scanner’s 
Maximum] page size setting is selected, scanning 
document page lengths up to 3,000 mm (118.1) is 
enabled.
[ON1]: When the [Match original size] or [Scanner’s 
Maximum] page size setting is selected, scanning 
document page lengths up to 1,000 mm (39.4) is 
enabled.
[OFF]: When the [Match original size] page size setting is 
selected, scanning document page lengths up to 432 mm 
(17.0) is...

3-5
Chapter 3   Basic Operation
2.
Document Feed and Eject Trays
Before scanning, prepare the Document Feed and Eject Trays for the desired paper size.Preparing the Document Feed Tray■Document Feed Tray
The height of the Document Feed Tray can be adjusted 
according to the number of document pages to be loaded 
(the default setting is the lowest position). 
 Tray Position Setting
The proper height of the Document Feed Tray can be set in 
advance by the Tray Position in the User Mode setting, 
which...

3-6
Chapter 3   Basic Operation
4.
Press [Enter].
The current setting is indicated by blinking square brackets 
[ ].
5.
Select with the [ ] or [ ] key and press [Enter] to 
accept the selection.
The Document Feed Tray moves to the selected height.
 
6.
Press the Stop key to exit the User Mode.
■Document Guides
Slide the document guides to fit the width of your 
document.
Hint
The positions of the left and right document guides can also be 
locked independently for off-center loading. (See “Adjusting the...

3-7
Chapter 3   Basic Operation
Gently open the extension wire.
Hint
Use the extension wire if the document beyond the edge of the 
document tray extension.
Adjusting the Document GuidesThe document guides normally extend at equal distances to 
the left and right ends from the center of the feeder so that 
documents are by default to be placed at the center of the 
feeder inlet.
However, each document guide has its own lock lever, so you 
can place documents either toward the left or right side of the...

3-8
Chapter 3   Basic Operation
4.
Lock the right document guide (1), and unlock the left 
document guide (2).
5.
Slide the left document guide to the left edge of your 
documents.
■Resetting the Document Guides
To reset the guides so that they are equidistant from the 
center, perform the following procedure to spread the 
guides to the left and right as far as they will go.
1.
Confirm that the right document guide is locked (1), 
and slide the left guide all the way to the left (2).
2.
Lock the left...

3-9
Chapter 3   Basic Operation
4.
Unlock the left document guide.
Preparing the Document Eject TrayThe Eject Tray includes two Document Eject Guides, the 
Eject Tray Extension and Eject Paper Stopper, to be adjusted 
to fit the width and length of your documents.■Document Guides
Slide the document eject guides to fit the width of your 
documents.
The eject position of the document can be checked by 
feeding a single sheet of the document in Count-Only 
Mode. (See “Count-Only Mode” on p. 4-2.)
■Document...

3-10
Chapter 3   Basic Operation
3.
Document Feeding Methods
Two document feeding methods are available: Continuous Feeding, which feeds documents automatically from the document tray 
by the pickup roller; and Manual Feeding, which requires manually feeding one document at a time for transport by the feed roller, 
while the pickup roller is disabled.Selecting the Document Feeding MethodContinuous Feeding is the default feeding method, but 
Manual Feeding can be enabled by selecting Manual Feeding 
as...

3-11
Chapter 3   Basic Operation
Continuous Manual Feeding Mode
Enable the Continuous Manual Feeding Mode from the 
User Mode when document pages do not separate well 
using Continuous Feeding.
IMPORTANT
When the Continuous Manual Feeding Mode is set to ON from 
the User Mode, make sure to disable it (set to OFF) when 
finished scanning. Otherwise, normal continuous feeding will be 
disabled the next time someone uses the scanner. 
Hint
For Manual Feeding, you must feed document one page at a 
time. For...