Canon scanner imageFORMULA DR6030C User Manual

							Appendices105
Chapter 4
6.Wipe the removed rollers with a firmly wrung cloth moistened with water.
IMPORTANT
Do not use detergent to clean the rollers, since any detergent on the rollers 
could cause a feeding error.
7.Attach the rollers that werw removed.
- See “Attaching the Pickup Roller,” on p. 115.
- See “Attaching the Feed Roller,” on p. 118.
- See “Attaching the Retard Roller,” on p. 121.
8.Be sure that the upper unit is completely closed by pushing on both edges with 
both hands until you hear a click.
IMPORTANT
Do not force the upper unit to close. Doing so may damage the scanner. 
						

							106Appendices
Cleaning the Shading Boards
The shading boards are the white standard boards located behind the platen 
rollers. A dirty shading board may alter scanned colors or cause marks on the 
images.
1.Turn ON the power.
2.Hold the upper unit as shown in the diagram, and open it slowly until it stops.
CAUTION
The pickup roller is located in the middle of the upper unit. Do not 
hold the protrusion on the upper unit when you open it. Doing so 
may deform the pickup roller or cause a feeding error.
IMPORTANT
Be sure to open the upper unit until it stops. If it is not opened all the way, the 
shading boards cannot come out.
3.Press the start button for about two seconds.
The shading boards come out above the platen rollers (upper and lower).
4.Wipe the only surface of the shading boards with a firmly wrung cloth 
moistened with water.
CAUTION
Wipe both the upper and lower shading boards.
Shading Boards 
						

							Appendices107
Chapter 4
5.Press the stop button.
The shading board goes back in.
6.Close the upper unit slowly. Be sure that the upper unit is completely closed by 
pushing on both edges with both hands until you hear a click.
IMPORTANT
Do not force the upper unit to close. Doing so may damage the scanner. 
						

							108Appendices
2. Removing and Attaching the Rollers
Follow the relevant procedure to remove and attach the pickup roller, feed 
rollers and retard roller when you clean or replace them.
IMPORTANT
Feed rollers are consumable parts. When the rollers start to wear out, paper 
jams and misfeeds may occur more often. When this happens, buy a exchange 
roller kit, and replace the pickup roller, feed rollers and the retard roller.
CAUTION
• Turn ON the power to the scanner to remove or attach the pickup 
roller. Be careful when working on the scanner when the power 
is ON.
• Do not use excessive force when removing or attaching the 
rollers. Doing so may damage them.
Roller Replacement Cycle
When the rollers being used have fed more than 250,000 pages, a roller 
replacement message is displayed on the computer. Buy a roller replacement 
kit and change the pickup roller, feed rollers and the retard roller. 
IMPORTANT
• If misfeeds happen often, check the rollers for wear, and replace them if 
necessary before the message is displayed.
• Be sure to reset the counter after replacing the rollers. (See “Resetting the 
Counter,” on p. 109.)
• Contact your local authrized Canon dealer or service representative for 
information about the exchange roller kit (pickup roller, feed rollers and 
retard roller). 
						

							
Appendices109
Chapter 4
Resetting the Counter
After replacing the feed rollers, open the [Counter setup] dialog box and reset 
the counter.
1.Follow the procedure below to open the [CANON DR-6030C USB Properties] 
(or [CANON DR-6030C SCSI Properties]) dialog box. 
1. Click the [Start] button, and then click [Control Panel]. 
						

							
110Appendices
2. This operation depends on your operating system.
„Windows XP
Switch the Control Panel to Classic View, or select [Printers and Other 
Hardware] in the working field.
„ Windows Vista
Switch the Control Panel to Classic View, or select [Hardware and sound] in 
the working field.
„ Windows 7
Click [View by] at the upper-right of the Control Panel, and then select 
[Large icons] or [Small icons] from the list, or select [Hardware and Sound] 
in the category view.
Printers and Other Hardware
Control Panel (category view)
Control Panel (classic view) 
						

							Appendices111
Chapter 4
3. Click [View devices and printers]. (For Windows XP and Windows Vista, 
click [Scanners and Cameras].)
4. Select [CANON DR-6030C] (or [CANON DR-6030C SCSI]), and then 
click the right mouse button and select [Properties]. (For Windows XP and 
Windows Vista, select [CANON DR-6030C USB] (or [CANON DR-6030C 
SCSI]), and then click [Properties].) 
						

							
112Appendices
[CANON DR-6030C USB Properties] (or [CANON DR-6030C SCSI 
Properties]) is displayed.
2.Click the [Maintenance] tab. 
						

							Appendices113
Chapter 4
3.Click the [Reset] button, and then make sure that the counter for the roller 
being used is set to 0.
Removing and Attaching the Pickup Roller
When cleaning or replacing the pickup roller, feed rollers or retard roller, use 
the appropriate procedure to remove and replace the rollers.
CAUTION
• Turn ON the power to the scanner to remove or attach the pickup 
roller. Be careful when working on the scanner when the power 
is ON.
• Do not use excessive force when removing or attaching the 
rollers. Doing so may damage them. 
						

							114Appendices
Removing the Pickup Roller
1.Turn ON the power.
Note
Because the pickup roller locks when the power is OFF, it will not fall forward 
when the upper unit is opened.
2.Hold the upper unit as shown in the diagram, and open it slowly until it stops.
CAUTION
The pickup roller is located in the middle of the upper unit. Do not 
hold the protrusion on the upper unit when you open it. Doing so 
may deform the pickup roller or cause a feeding error.
3.Push up on the pickup roller to open the hook, and then remove the pickup 
roller.
When the power is ON When the power is OFF