Canon Projector WUX6010 User Manual

101
Menu Description
Advanced Guide
Menu Description
SubmenuFunction
SideLeft, Right, 
To p ,  B o t t o mSelect the direction of the blending area to adjust.
WidthSpecify the width between the start and end markers.
Start 
positionMoves the position of the start marker.
Color blending 
adjustmentAdjust unwanted colors or discrepancies between colors in the blending 
area.
SubmenuFunction
Off Do not adjust colors of blended images.
AdjustAdjust unwanted colors or discrepancies between colors 
in the...

Menu Description
102
SubmenuFunction
Black level 
adjustmentBecause black is lighter in the blending area than in other areas, you can 
adjust the black level outside the blending area to make this difference in 
brightness less noticeable.
Off
Do not adjust the black level.
Area
Adjust areas C - A to smoothen the boundaries of the blending area.
Black level
Adjust the black level brightness and color of areas B and D.
MarkerShow the blending area markers.
OptionFunction
Off Hide the blending area...

103
Menu Description
Advanced Guide
Menu Description
Lens - Position
> [Install settings] > [Lens - Position] 
The projector can save information about the lens position in memory. Up to three 
sets of lens information (including focus, zoom, and lens shift settings) can be 
saved, and the lens can be restored to these positions.
SubmenuFunction
Corner adjustmentCorrect image distortion by aligning corners of the blending area with the 
image from the reference projector. For multi-projection alignment,...

Menu Description
104
Screen color
> [Install settings] > [Screen color] 
You can adjust the color quality of the images projected according to the color of 
the projection screen.
On screen
> [Install settings] > [On screen] 
Specify display details for on-screen menus, help, and warning or precaution icons.
• [Load position] is not available unless you perform [Save position] once.
• The original lens position varies depending on the type of lens used.
• When saved lens positions are restored, images...

105
Menu Description
Advanced Guide
Menu Description
Show input status
Specify whether signal status is shown when there is no signal or when you are completing 
signal settings.
OptionFunction
Off The input status is not displayed.
On The input status is displayed.
Overheat warning display
Specify whether the icon warning of high temperature ( ) is shown when the internal 
temperature is high and the projector may overheat.
OptionFunction
Off Disable high temperature warning icon display.
On Enable high...

Menu Description
106
Test pattern
> [Install settings] > [Test pattern] 
You can project a test pattern (P179) to check resolution, color, and other details 
even without supplying an input signal. 
Lamp warning display
Specify whether to show a lamp replacement message after the lamp has been used for a 
specified period.
OptionFunction
Off The prepare lamp message and the lamp warning are not displayed.
On The prepare lamp message and the lamp warning are displayed.
Air filter warning display
A message...

107
Menu Description
Advanced Guide
Menu Description
System settings
Customize projector and remote control operation, beeping, and other 
details after startup, during standby, and in other situations.
(When the input signal is Analog PC-1)
MenuFunctionDetails
User screen settingsCustomize user screens shown at startup, when no 
signal is detected, and in other situations.P108
Interface settingsSpecify interface details such as settings for input 
signals of connected equipment.P109
Power management...

Menu Description
108
User screen settings
> [System settings] > [User screen settings] 
Capture a logo and specify logo display settings.
Logo capture
Registers the current image as a user logo. Registered user logos can be shown when no 
signal is received, when the BLANK button is pressed, or as the startup image.
OptionFunction
OKDisplay the image for logo registration.
Align the image with the red boundary lines indicating the portion that 
will be stored, and then press the OK button. The portion of...

109
Menu Description
Advanced Guide
Menu Description
Interface settings
> [System settings] > [Interface settings] 
Specify interface details such as settings for input signals of connected equipment.
Projector on
Select a logo to project after startup until input signals can be projected.
OptionFunction
Skip A black screen is projected.
Canon logo Displays the Canon logo that was registered in advance at the factory.
User logo The user logo is projected.
Key repeat
Key repeat enables projector or remote...

Menu Description
110
Remote control channel
Separate channels can be assigned to up to four projectors so that a single remote control 
can be used with each projector.
Selecting the Projector Channel
If an optional wired remote control (RS-RC05) is used, there is no need to set the remote 
control channel.
OptionFunction
Ch1
Ch2
Ch3
Ch4Select the remote control channel to use with this projector.
Independent Can be controlled from a remote control set to any channel.
Selecting a Channel on the Remote...