Canon Projector WUX6010 User Manual

Projection Procedure
61
Basic Guide
Projection Procedure
■Adjusting the Image Position
To adjust the screen position up, down, left, or right, press the LENS-SHIFT button 
on the remote control or the LENS button on the projector. It can change the 
projected screen to the most suitable position by moving the position of the lens up/
down/left/right.
1Press either the LENS-SHIFT button on the remote control or the LENS 
button on the projector three times to display the lens shift adjustment 
window....

62
Projection Procedure
■Resetting the Position
The lens position after movement with the 
lens shift function is not returned when the 
power is turned off. To return it to its original 
position, perform reset.
During screen position adjustment, press and 
hold the LENS-SHIFT button on the remote 
control or the LENS button on the projector to display the [Lens shift reset] window.
The selections for the lens currently used are displayed. Use the pointer buttons to 
select one of them, then press the...

Projection Procedure
63
Basic Guide
Projection Procedure
Step 4 Select an Aspect Ratio (Screen Aspect) 
Matching the Screen
Select an optimum aspect ratio of the projected image (screen aspect) or an 
optimum screen mode (aspect) according to the aspect ratio of the screen, type of 
input image signal and so on for the projection to make best use of the screen size.
You may need to change the setting depending on the resolution of the computer or 
other AV equipment connected. If the image is not...

64
Projection Procedure
3Select [Screen aspect] with the [ ] / [ ] buttons, and then press the OK 
button.
4Use the [ ] / [ ] buttons to select the desired contents.
16:10
Select this when you use a screen with an aspect 
ratio of 16:10. Also select this screen aspect when 
projecting on a wall. You can correct keystone 
distortion with this mode. (P67)
16:9
Select this when you use a screen with an aspect 
ratio of 16:9. You can correct keystone distortion with 
this mode. (P67)
4:3
Select this when you...

Projection Procedure
65
Basic Guide
Projection Procedure
4:3 D. image shift
Select this when you use a screen with an aspect ratio of 4:3. Keystone correction 
cannot be performed in this mode. However, it is possible to move the image left / 
right when projecting level. For details about how to move the image, refer to 
“Digital image shift” on page 98.
5Press the OK button to accept your setting and then press the MENU 
button.
Resetting the Image Shift
Perform the following steps to reset the image...

66
Projection Procedure
■Tr u e  s i z e
The image is projected with the original resolution of the input signal. Screens of 
computers with a lower display resolution than the projector are displayed smaller 
but clearer than in other aspect ratios.
Selecting an Aspect Ratio
Press the ASPECT button on the remote control and select an appropriate aspect 
ratio. Press the ASPECT button to change the aspect ratio type. For more details 
about aspect ratios, refer to “Relationship between Aspect and Screen...

Projection Procedure
67
Basic Guide
Projection Procedure
Step 5 Adjusting Keystone Distortion
To correct keystone distortion, press the D.SHIFT/KEYSTONE button.
Two types of correction are available: horizontal/vertical correction and corner 
correction.
Use horizontal/vertical keystone correction to adjust image width or height 
distortion separately, and use corner correction to adjust the position of each corner 
of the image.
For instructions on switching keystone correction, refer to “Keystone”...

68
Projection Procedure
2Press the pointer buttons to adjust the dimensions.
3When keystone distortion has been corrected, press the OK button.
■Corner Adjustment
1Press the D.SHIFT/KEYSTONE button on the remote control to display the 
corner adjustment window when [Keystone] is set to [Corner 
adjustment].
To correct top distortion, 
press the [ ] button.To correct bottom distortion, 
press the [ ] button.
To correct distortion on the 
right, press the [ ] button.
Screen
To correct distortion on the...

Projection Procedure
69
Basic Guide
Projection Procedure
2Press the pointer button of the corner for correction, and then press the 
OK button.
3Press the pointer buttons to adjust the corner.
4When you have finished correcting, press the OK button.
■Resetting the Keystone Adjustment
Horizontal-vertical keystone and corner adjustment can be reset as follows.
First, press the D.SHIFT/KEYSTONE button on the remote control twice to display 
the [Keystone reset] window. 
Next, select [OK] with the [ ]...

70
Projection Procedure
Step 6 Select the Image Quality (Image Mode)
You can select an image mode to suit the projected image.
In each image mode, you can further adjust the brightness, contrast, sharpness, 
gamma, color adjustment, advanced adjustment, and lamp mode. (P88)
Image Modes
Available image modes vary depending on the selected input signal and whether 
[HDMI image input] (P112) and [HDBaseT image input] (P112) is set to [Auto] or 
[Computer].
: Compatible    : Not compatible
*1 [HDMI image...