Canon Projector WUX6010 User Manual

							101
Menu Description
Advanced Guide
Menu Description
SubmenuFunction
SideLeft, Right, 
To p ,  B o t t o mSelect the direction of the blending area to adjust.
WidthSpecify the width between the start and end markers.
Start 
positionMoves the position of the start marker.
Color blending 
adjustmentAdjust unwanted colors or discrepancies between colors in the blending 
area.
SubmenuFunction
Off Do not adjust colors of blended images.
AdjustAdjust unwanted colors or discrepancies between colors 
in the blending area.
• Large blending areas may cover input signal dialog boxes and 
other interface elements. In this case, momentarily set edge 
blending to [Off] and check the display.
• Although the starting marker is normally aligned with the image 
edge, it can also be aligned toward the center of the image. In 
this case, the black blending area will lie outside of the starting 
marker.
OptionFunction
WhiteSimultaneously adjust red, green, 
and blue to correct unwanted 
colors or discrepancies in the 
blending area.
Red/Green/BlueIndividually adjust red, green, and 
blue to correct unwanted colors or 
discrepancies in the blending 
area. 
						

							Menu Description
102
SubmenuFunction
Black level 
adjustmentBecause black is lighter in the blending area than in other areas, you can 
adjust the black level outside the blending area to make this difference in 
brightness less noticeable.
Off
Do not adjust the black level.
Area
Adjust areas C - A to smoothen the boundaries of the blending area.
Black level
Adjust the black level brightness and color of areas B and D.
MarkerShow the blending area markers.
OptionFunction
Off Hide the blending area markers.
OnShow the blending area markers. The start marker is red, 
and the end marker is green.
Reset Reset the marker settings.
$#
Left imagePosition of end 
marker (hidden)
Area D
Blending area
Areas C - A (default: 0)
Area A:  Black level cannot be adjusted.
Area B:  Adjust to a black level different 
from that of area D.
Area C:  Adjust to provide a smooth 
transition relative to the black 
levels of areas B and D.
OptionFunction
SideSelect the direction to adjust from Left/Right/
Top/Bottom.
A-Width/ B-Width/ 
C-WidthAdjust the widths of areas A - C.
OptionFunction
B/D-area base Adjust the black level brightness of B/D areas.
B/D-area red / green / 
blueAdjust the red, green, and blue components of 
B/D area black levels individually. 
						

							103
Menu Description
Advanced Guide
Menu Description
Lens - Position
> [Install settings] > [Lens - Position] 
The projector can save information about the lens position in memory. Up to three 
sets of lens information (including focus, zoom, and lens shift settings) can be 
saved, and the lens can be restored to these positions.
SubmenuFunction
Corner adjustmentCorrect image distortion by aligning corners of the blending area with the 
image from the reference projector. For multi-projection alignment, align 
the corners with the projector blending area (already adjusted) that forms 
the basis.
Left, Right, 
To p ,  B o t t o mSelect the direction of the blending area to adjust. As you 
reposition the corners of the selected area, the overall 
image changes to match the adjustment.
SubmenuFunction
Load position 1-3 Restores the lens to the positions saved using Save position 1-3.
Save position 1-3 Saves the lens position as positions 1-3.
Lens shift reset Restores the lens to the original position.
• To lock (protect) the saved position, set [Positional lock] (P96) to [On].
• The values of the following settings are saved in addition to the lens position 
information:
-Horizontal/vertical keystone / corner adjustment
-Screen color
-Screen aspect
-Zoom
-Digital image shift
Points to adjust
Blending area
• Sides set to an edge-blending width of 12 or more can be 
adjusted when [Keystone] is set to [Corner adjustment] and the 
aspect ratio is [16:10].
• To reset adjustment, use [Keystone] (P69). 
						

							Menu Description
104
Screen color
> [Install settings] > [Screen color] 
You can adjust the color quality of the images projected according to the color of 
the projection screen.
On screen
> [Install settings] > [On screen] 
Specify display details for on-screen menus, help, and warning or precaution icons.
• [Load position] is not available unless you perform [Save position] once.
• The original lens position varies depending on the type of lens used.
• When saved lens positions are restored, images may be projected in a slightly different 
position than the saved position.
• Specifying a somewhat smaller image size than the screen size (image area) enables 
you to switch among multiple lens positions without having the image extend off the 
screen.
• When precise positioning is needed, use lens shift, zoom, and focus functions for fine 
adjustment.
SubmenuFunction
NormalSelect this if a standard type of projection screen is used. The images 
are projected in a light quality similar to that of natural light.
GreenboardSelect if a dark green surface such as a blackboard is used as the 
screen. The color quality similar to [Normal] is obtained on the 
greenboard.
Adjust Select to fine-tune red, green and blue.
Menu position
Reposition menu display.
Use the [ ] / [ ] / [ ] / [ ] buttons to move the menu to the desired position.
Guide
Shows the guide screen.
OptionFunction
Off Hides the guide screen.
On Shows the guide screen. 
						

							105
Menu Description
Advanced Guide
Menu Description
Show input status
Specify whether signal status is shown when there is no signal or when you are completing 
signal settings.
OptionFunction
Off The input status is not displayed.
On The input status is displayed.
Overheat warning display
Specify whether the icon warning of high temperature ( ) is shown when the internal 
temperature is high and the projector may overheat.
OptionFunction
Off Disable high temperature warning icon display.
On Enable high temperature warning icon display.
Menu display time
Extend menu display from the standard 10 or 30 seconds to 3 minutes.
OptionFunction
Normal The menu is displayed for 10 or 30 seconds.
Extended The menu is displayed for 3 minutes.
The following display times are also changed.
The guide screen is shown at the following cases.
• No input signal is detected. (P54)
• An invalid button is pressed in [BLANK], [FREEZE], or [D.ZOOM] mode. (P34)
• When positional lock (P96) is set to [On] and buttons locked by this feature are 
pressed.
• When the projector is already on and the POWER button is pressed.
Item [Normal] [Extended]
- MENU screen
- Power-Saving Settings (P73)30 seconds 3 minutes
- Input (P56)
- Keystone adjustment (P67)
- Keystone reset (P69)
- Focus adjustment (P59)
- Zoom adjustment (P60)
- Lens shift adjustment (P61)
- Lens shift reset (P62)
- D.image shift adjustment (P64)
- D.image shift reset
- Aspect (P65)
- Image mode (P70)
- Volume adjustment (P74)
- Gamma correction (P89)10 seconds 3 minutes 
						

							Menu Description
106
Test pattern
> [Install settings] > [Test pattern] 
You can project a test pattern (P179) to check resolution, color, and other details 
even without supplying an input signal. 
Lamp warning display
Specify whether to show a lamp replacement message after the lamp has been used for a 
specified period.
OptionFunction
Off The prepare lamp message and the lamp warning are not displayed.
On The prepare lamp message and the lamp warning are displayed.
Air filter warning display
A message advising you to perform cleaning can be set to display when the filter needs 
cleaning.
OptionFunction
Off The air filter warning is not displayed.
On The air filter warning is displayed.
Split screen ID display
Specify whether to show the digit (1 or 2) identifying screens in split-screen mode. Note that 
even if [Off] is selected, corner markers will be shown to indicate the side with control rights.
OptionFunction
Off Hides the screen ID.
On Shows the screen ID.
OptionFunction
Off Disable test pattern display.
On Enable test pattern display.
• While the test pattern menu is displayed, you can use the [ ] / [ ] buttons to switch 
patterns. Additionally, options of test pattern that have options can be changed with the 
[ ] / [ ] buttons.
• The test pattern menu is no longer displayed after a little while, but you can view it 
again by pressing the [ ] / [ ] buttons.
• When it is almost time to replace the lamp, the projector’s [LAMP] indicator will 
flash. For details, see “LED Indicator Displays” (P31).
• Setting display to [Off] will disable both the message to prepare a replacement lamp 
and the warning to replace the lamp. To review the replacement timing, check the 
lamp counter (P116).
• Lamps that are still used after the timing for lamp replacement are more likely to 
rupture. Replace the lamp with a new one as soon as possible.
Setting [Air filter warning display] to [Off] will disable display of the warning to clean 
the air filter. We recommend checking the air filter counter (P117) occasionally to 
know when to replace the filter. 
						

							107
Menu Description
Advanced Guide
Menu Description
System settings
Customize projector and remote control operation, beeping, and other 
details after startup, during standby, and in other situations.
(When the input signal is Analog PC-1)
MenuFunctionDetails
User screen settingsCustomize user screens shown at startup, when no 
signal is detected, and in other situations.P108
Interface settingsSpecify interface details such as settings for input 
signals of connected equipment.P109
Power management 
modeYou can specify to turn the lamp or projector off 
automatically after a certain period if the projector and 
remote control are not used, or if there is no input 
signal.P112
Power management 
durationSpecify how long before the lamp is turned off or the 
projector enters standby, depending on the [Power 
management mode] setting.P113
Direct power onYou can turn on the projector by connecting the power 
cable without pressing the POWER button.P113
BeepYou can select whether a beep sounds or not when you 
operate the projector.P113
Motion blur reductionMotion blur is blurring that occurs during video 
playback. Motion blur reduction can make this blurring 
less noticeable.P114
LanguageYou can select the language in which the menus are 
displayed.P114
Other settingsSet a password, reset counters for lamp or air filter 
replacement, and access other settings and 
information.P115 
						

							Menu Description
108
User screen settings
> [System settings] > [User screen settings] 
Capture a logo and specify logo display settings.
Logo capture
Registers the current image as a user logo. Registered user logos can be shown when no 
signal is received, when the BLANK button is pressed, or as the startup image.
OptionFunction
OKDisplay the image for logo registration.
Align the image with the red boundary lines indicating the portion that 
will be stored, and then press the OK button. The portion of the image 
within the boundary lines is now registered.
Cancel Cancels logo registration.
Logo position
Specify the position of registered user logos as follows.
You can specify the position after a logo has been registered. Choose from upper left, upper 
right, center, lower left, or lower right.
No signal screen
Customize the screen shown when no input signals are received.
OptionFunction
Black The screen is all black.
Blue The screen is all blue.
User logo The user logo is projected.
Screen when blank
Select the screen shown when projection is temporarily blanked out by pressing the BLANK 
button on the remote control.
OptionFunction
Black The screen is all black.
Blue The screen is all blue.
User logo The user logo is projected.
Only images at an aspect ratio of 16:10 can be registered as user logos. 
						

							109
Menu Description
Advanced Guide
Menu Description
Interface settings
> [System settings] > [Interface settings] 
Specify interface details such as settings for input signals of connected equipment.
Projector on
Select a logo to project after startup until input signals can be projected.
OptionFunction
Skip A black screen is projected.
Canon logo Displays the Canon logo that was registered in advance at the factory.
User logo The user logo is projected.
Key repeat
Key repeat enables projector or remote control buttons to be held down instead of pressing 
them repeatedly.
OptionFunction
Off Key repeat is not enabled.
On Key repeat is enabled.
Key lock
Lock the projector to prevent direct or remote control operation.
OptionFunction
Off Disables the key lock.
Main unitOperation is not possible using the main unit.
Use the remote control.
Remote (wireless)Disables infrared remote control operations (P37). Use buttons on the 
main unit.
Operation is also possible with an optional wired remote control (RS-
RC05). 
						

							Menu Description
110
Remote control channel
Separate channels can be assigned to up to four projectors so that a single remote control 
can be used with each projector.
Selecting the Projector Channel
If an optional wired remote control (RS-RC05) is used, there is no need to set the remote 
control channel.
OptionFunction
Ch1
Ch2
Ch3
Ch4Select the remote control channel to use with this projector.
Independent Can be controlled from a remote control set to any channel.
Selecting a Channel on the Remote Control
After changing the projector channel from the menu, always change the remote control 
channel accordingly.
Audio in terminal select
Select the source terminal for audio output.
OptionFunction
Off No audio is output.
Audio in 1 Use audio signals from AUDIO IN 1 for audio output.
Audio in 2 Use audio signals from AUDIO IN 2 for audio output.
HDMI Use HDMI audio signals for audio output.
HDBaseT Use HDBaseT audio signals for audio output.
LANUse LAN audio signals for audio output. Audio is transferred by the 
NMPJ application.
To Unlock Key Lock Function
Turn off the projector and unplug the power plug. Hold down the OK button on the main unit 
and plug in the power cord, as you continue to hold down the OK button. In a moment, a 
beep will sound, and the controls will be unlocked.
When you access this setting from the projector’s side controls, [Main unit] is not 
available. Similarly, when you access the setting from the remote control, [Remote 
(wireless)] is not available.
Ch1 Hold both the OK button and [ ] button for 3 seconds.
Ch2 Hold both the OK button and [ ] button for 3 seconds.
Ch3 Hold both the OK button and [ ] button for 3 seconds.
Ch4 Hold both the OK button and [ ] button for 3 seconds.
Independent Hold both the OK button and MENU button for 3 seconds.
Audio is transferred via the port selected in [Communication 
settings] > [Wired network] (P 111).