Canon Projector WUX6010 User Manual

							11
Safety Instructions
Safety InstructionsThis section describes the safety symbols used in this manual. Important projector 
safety information is identified by the following symbols. Always observe the safety 
information by these symbols.
Safety Symbols in this Manual
Denotes the risk of death or serious injury from improper 
handling if the information is not observed. To ensure safe use, 
always observe this information.
Denotes the risk of injury from improper handling if the 
information is not observed. To ensure safe use, always observe 
this information.
Denotes prohibited actions.
Denotes required actions or information that must be observed. 
						

							Safety Instructions
12
Precautions for Use
As this section contains important safety-related information, be sure to read the 
following carefully beforehand in order to use your projector correctly and safely.
During installation, keep the projector plug easily accessible so that the projector can be 
unplugged immediately if necessary, or keep a circuit breaker within reach.
If the following situations occur, turn the power off, remove the power plug from the 
power outlet and contact the Canon Customer Support Center. Failure to do so could 
cause a fire or result in an electric shock.
•If smoke is emitted
•If an unusual smell or noise is emitted
•If water or other liquid has entered the projector
•If metal or any other foreign material has entered the projector
•If the projector is knocked over or dropped and the cabinet is damaged
Pay attention to the following points for handling the power cord. Failure to do so may 
cause a fire, electric shock or personal injury.
•Do not place any objects on the power cord and do not allow it to become 
trapped under the projector. 
•Do not cover the power cord with a carpet.
•Do not modify or excessively bend, twist, pull, wind, or bundle the power 
cord.
•Keep the power cord away from heaters and other sources of heat.
•Do not use a damaged power cord. If the power cord is damaged, purchase 
a replacement from your dealer.
•The power cord included with this projector is for use exclusively with this 
product. Do not use this cord for other products.
•Be sure to connect the ground wire of the power cord to ground.
•Be sure to connect the ground wire before connecting the power plug to the 
outlet. Also when you disconnect the ground wire, be sure to unplug the 
power plug from the outlet beforehand. 
						

							13
Safety Instructions
Safety Instructions
Pay attention to the following points regarding the power source, power plug and 
handling of the connector. Failure to do so may cause a fire, electric shock or personal 
injury.
•Do not use any power source with a voltage other than the voltage indicated 
(AC 100–240 V).
•Do not pull the power cord and be sure to hold the power plug or connector 
when removing. Incorrect handling may damage the power cord.
•Do not insert any metal objects into the contact parts of the power plug or 
connector.
•Do not remove the power plug or connector with wet hands.
•Insert the power plug and connector securely up to the base. Additionally, do 
not use a damaged power plug or an outlet that is loose.
•When using an extension cord, do not exceed the cord’s rated capacity.
•Periodically inspect the power plug and outlet and remove any dust or dirt 
from between the plug and the outlet.
Installation and Handling Precautions
Pay attention to the following points regarding installation and handling of the projector. 
Failure to do so may cause a fire, electric shock or personal injury.
•Do not use the projector where it might get wet, such as outdoors or by 
bathtubs or showers.
•Do not place containers containing a liquid on top of the projector.
•Do not touch the projector itself, the power cord, or the cable if lightening 
strikes.
•Do not move the projector until you have switched off the power, removed 
the power plug from the power outlet and unplugged any other cables.
•Unplug the projector before cleaning or maintenance.
•Before you attach or replace a lens unit, be sure to unplug the power plug of 
the projector from the power outlet. Failure to unplug the power cord could 
result in an electric shock or personal injury. 
						

							Safety Instructions
14
Pay attention to the following points regarding installation and handling of the projector. 
Failure to do so may cause a fire, electric shock or personal injury.
•Do not remove the cabinet from the projector or disassemble it. The interior 
of the projector contains high-voltage components as well as parts that are 
hot. If inspection, maintenance or repair is required, contact the Canon 
Customer Support Center.
•Do not disassemble or modify the projector (including consumable parts) or 
the remote control.
•Do not look directly into the exhaust vents during use.
•Do not insert any object into vents in the projector, such as the air intake vent 
or exhaust vents.
•Do not place a pressurized can in front of the exhaust vents. The pressure of 
the contents of the can may increase due to heat from the exhaust vents and 
this could result in an explosion.
•When cleaning off dust or dirt from the projector lens etc., do not use any 
kind of spray that is flammable. As the temperature of the lamp inside the 
projector is high, it could ignite, causing a fire.
•As strong light beams are emitted while the projector is in use, do not look 
directly into the projector lens. Doing so could cause an eye injury. Pay 
particular attention to prevent small children from doing so.
•When setting the projector on a high surface for projection, be sure the 
surface is flat and stable. 
•For ceiling mounting precautions, refer to the installation manual included 
with the ceiling mount (sold separately).
•When hanging the projector from a ceiling, put the projector down on the 
floor or a workbench before attaching or replacing the lens unit. Failure to do 
so could result in parts falling off the projector and may cause an accident or 
personal injury.
Precautions on the Lamp
This projector uses a high-pressure mercury lamp, which must be handled 
carefully and correctly as described below.
The mercury lamp has the following characteristics.
•The lamp will gradually become darker over time.
•Impact, abrasion, or use of worn-out lamps may cause lamps to rupture 
(accompanied by a loud noise) or burn out.
•Lamps are more likely to rupture after the lamp replacement message is 
displayed (see “Replacing the Lamp” (P165)). Replace the lamp with a new 
one as soon as possible.
•Useful life of lamps varies widely from lamp to lamp and depending on the 
environment of use. Some lamps may fail or rupture soon after they are first 
used.
•Be prepared by keeping a spare lamp. 
						

							15
Safety Instructions
Safety Instructions
Note the following precautions during lamp replacement or when a lamp has ruptured. 
Failure to do so could result in an electric shock or personal injury.
•Before replacing the lamp, always unplug the projector and wait at least an 
hour.
•Ruptured lamps may scatter shards of glass inside the projector. Contact the 
Canon Customer Support Center for cleaning and inspection of the projector 
interior and lamp replacement.
Precautions when replacing lamps that stop working
•If illumination suddenly stops, either when you turn the projector on or after it 
has been on for a while, the lamp may have ruptured. In this case, never 
attempt to replace the lamp by yourself. Always request service from the 
Canon Customer Support Center. 
•With ceiling-mounted projectors, the lamp may fall out when you open the 
lamp cover, or during replacement. During replacement, stand to the side of 
the lamp cover, not directly under it. 
•If the lamp ruptures, dust and gas (containing mercury vapor) may come out 
of the exhaust vents. If this happens, immediately open the windows and 
doors to provide ventilation to the room.
•If you accidentally inhale gas from the lamp or get any pieces in your eyes or 
mouth, consult a doctor immediately.
Precautions for the Batteries of the Remote 
Control
Pay attention to the following points regarding handling of batteries. Failing to do so 
could result in a fire or personal injury.
•Do not heat, short circuit or disassemble the batteries, or place them in a fire.
•Do not attempt to recharge the batteries that are included with the remote 
control.
•Remove the batteries when they are flat or when the remote control will not 
be used for a long period of time.
•When replacing the batteries, replace both at the same time. Also, do not 
use two batteries of a different type at the same time.
•Insert the batteries with the + and - terminals in the correct directions.
•If any liquid from inside the batteries leaks out and contacts your skin, be 
sure to wash the liquid off thoroughly. 
						

							Safety Instructions
16
Pay attention to the following points regarding installation and handling of the projector.
•If the projector will not be used for a long period of time, be sure to remove 
the power plug from the power outlet to ensure safety. Failure to do so 
presents a risk of fire if dust accumulates on the plug or outlet.
•Parts of the cabinet around and above the exhaust vents may become hot 
during projection. Touching these areas during operation could cause burns 
to the hands. Pay particular attention in preventing young children from 
touching these parts. Additionally, do not place any metal objects around or 
above the exhaust vents. Due to the heat from the projector, doing so could 
cause an accident or personal injury.
•Do not place the projector where it may be exposed to oily smoke or steam, 
such as near kitchen counters or humidifiers. Doing so may cause fire or 
electric shock.
•Do not place any heavy objects on top of the projector or sit / stand on it. Pay 
particular attention to prevent small children from doing so. The projector 
may be knocked over and this could result in damage or a personal injury.
•Do not place the projector on an unstable or slanted surface. Doing so may 
cause the projector to fall or be knocked over and could result in a personal 
injury.
•Do not place any objects in front of the lens during projection. Doing so could 
cause a fire.
•Presenters in front of the projector should stand where the light does not 
seem too bright, and where their shadow does not fall on the screen.
•The projector is provided with a lens shift function to move the lens up, 
down, left, and right using the motor. Do not touch the lens while it is moving. 
Touching the lens when it is moving may result in personal injury.
•Before replacing the lens unit, wait at least one hour after the projector is 
turned off to allow the projector to cool thoroughly. Failure to do so could 
result in a burn or injury.
When handling the lamp, pay attention to the following points.
•Be sure not to handle the lamp immediately after it has been used. Be sure 
to switch off the power and wait for approximately 1 hour for the lamp and 
the projector to cool down sufficiently. Failure to do so could result in a burn 
or personal injury due to heat from the lamp or projector. 
						

							17
For Safe Use
For Safe Use
Pay attention to the following points when carrying or transporting the projector.
•This projector is a precision instrument. Do not knock it over or subject it to 
impacts. Doing so may cause a malfunction.
•Do not reuse any packaging or shock-absorbent materials that were 
supplied with the projector at the time of purchase for transporting or 
shipping the projector. Protection of the projector cannot be guaranteed if 
used packaging or shock-absorbent materials are reused. Fragments from 
shock-absorbent material may also enter the interior of the projector which 
could cause a malfunction.
•Removal and installation of the lens unit should not be performed by the 
user. Be sure to have the procedure performed by a qualified technician or 
contact the Canon Customer Support Center.
•Disconnect the cables connected to the projector. Carrying the projector 
while the cables are attached may cause an accident.
•Retract the adjustable feet before moving the projector. Leaving the feet 
extended may cause damage.
Pay attention to the following points when installing or using the projector.
•Do not touch the lens with bare hands. Doing so may result in deterioration 
of image quality.
•If the projector is abruptly taken from a cool to a warm location, 
condensation may form on the lens or mirrors, which may cause a blurred 
image. Wait until the condensation has evaporated for the image projected 
to return to normal.
•Do not install the projector in a location where the temperature is high or low. 
Doing so may cause a malfunction. For guidelines on operating 
temperatures, see “Product Specifications”.
•Do not place any objects on top of the projector that may change shape or 
color due to heat.
•Projector settings must be adjusted when using the projector at high 
altitudes or in upward or downward projection. Failure to adjust the settings 
may shorten the lamp life or damage the lamp. For details, contact the 
Canon Customer Support Center.
•Do not install the projector near high-voltage electrical power lines or an 
electrical power source.
•Do not use the projector on a soft surface such as carpet or sponge mat, etc. 
Doing so could cause heat to build up inside the projector and this could 
result in a malfunction.
•Do not block the air intake or exhaust vents of the cooling fan. If the air 
intake or exhaust vent is blocked, heat cannot be released from inside the 
projector, which may shorten the useful life of the lamp or cause malfunction.
•Installing the projector in the wrong direction may cause a malfunction or 
accident. Do not install the projector with one side raised, or with the 
projector tilted toward the left or right. 
						

							For Safe Use
18 •Install the projector with sufficient space between air intakes and exhaust 
vents and walls. Failure to do so could cause a malfunction.
•Do not install the projector in a location that is damp, or where there is a lot 
of dust, oily smoke or tobacco smoke. Doing so could cause contamination 
of optical components such as the lens and the mirror and may result in 
deterioration of image quality. 
						

							19
Before Installation
Before Installation
Precautions When Carrying/Shipping the 
Projector
Precautions for Installation
Be sure to read “Safety Instructions” and “For Safe Use” (P5 – P18). Also 
take the following precautions during installation.
■Do Not Use in the Following Environments
• Locations with excessive humidity, dust, oily smoke or tobacco smoke
Adhesion to the lens, mirrors or other optical parts may reduce image quality.
• Near high-voltage power lines or sources of electrical power
This may cause malfunction.
• On soft surfaces such as carpets or cushioned mats
Heat may build up inside the projector and damage it.
• Locations with excessive temperature or humidity
This may damage the projector. Acceptable ranges for operating and storage 
temperature and humidity are as follows.
*Operating temperature and humidity applies to when the projector is projecting 
or in standby mode.
Prepare the projector as described below before carrying it.
• Disconnect the cables connected to the projector. Carrying the 
projector with the cables attached may cause an accident.
• Retract the adjustable feet before moving the projector. Leaving 
the feet extended may cause damage.
• Do not strike the projector 
or subject it to impact. Doing 
so may cause a malfunction.
• Do not install the projector 
so that it is inclined or 
standing vertically. The 
projector may be damaged if 
it tips over.
• Do not block the air intake or 
exhaust vents of the cooling 
fan. Blocking the vents may trap heat inside the projector, which 
may shorten the useful life of the lamp or damage the projector.
Operating temperature Operating humidity Storage temperature
0°C (32°F) – 40°C (104°F)Up to 85%-30°C (-22°F) – 60°C (140°F)
Exhaust vent Air intake vent
Warmed 
airflow 
						

							Before Installation
20
■Do Not Touch the Lens with Bare Hands
Do not touch the lens with bare hands. Doing so may adversely affect picture 
quality.
■Allow a 30 Min. Warm Up before Focus Adjustment (P59), if Possible
The focus position may not stabilize immediately after startup, due to lamp heat. 
When adjusting focus, it is also helpful to use the test pattern (10) (P106, P179).
■Install at a Sufficient Distance from Walls and Other Obstructions
■Be Careful of Condensation
If the temperature of the room rises suddenly, moisture in the air may condense on 
the projector lens and mirror, causing the image to become blurred. Wait until the 
condensation has evaporated for the image projected to return to normal.
■At Altitudes above 2,300 m (7,545.8), Adjust the Settings
Projector settings must be adjusted when using the projector at altitudes of 2,300 m 
(7,545.8) or higher. Specifically, refer to instructions for [Fan mode] (P99) in the 
[Install settings] menu.
If the air intake or exhaust vent 
is blocked, heat will accumulate 
inside the projector, possibly 
resulting in a shortened 
projector lifetime or a 
malfunction. Do not install in a 
closet, on a bookshelf, or in 
other narrow spaces with poor 
ventilation. Install in a well-
ventilated location. (Ensure a 
minimum clearance of 50 cm (1.6 ft.) above, on both sides, and 
behind the projector, as shown below.)
Exhaust vent Air intake vent
Warmed 
airflow
50 cm 
(1.6)50 cm 
(1.6)50 cm 
(1.6)
50 cm (1.6)