Canon Projector WUX6010 User Manual

							131
Menu Description
Advanced Guide
Menu Description
■Mac OS X
1Open the Apple Menu and select [System Preferences].
2In the System Preferences window, click [Network] to display the Network 
window.
3Select [Built-in Ethernet] and click the [TCP/IP] tab. Make a note of the 
original network settings (IP address, subnet mask, router, DNS server, 
etc.).
4Create a new network environment and set the IP address and subnet 
mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP 
address which is different from this.
5Click [Apply] to close the network preference window.
■Resetting the IP Address Setting of the Computer
Follow the same procedure as for changing the IP address and reset the values to 
the original values based on the notes taken before the change.
Setting Up the Network
■Displaying the Network Configuration Screen
1Turn on the computer and projector.
2Launch a web browser, enter “http://(projector IP address)” in the 
address bar, and press the Enter key.
The projector web screen appears.
Network functions are not available for the first 40 seconds after projector startup. 
						

							Menu Description
132
The following information is displayed.
* For details on downloading the Networked Multi-Projection (NMPJ) application, 
refer to the NMPJ user’s manual.
3Click [Settings] on the web screen.
The password input window appears.
Network Multiple Projection 
DownloadFor downloading the Networked Multi-Projection 
(NMPJ) program.*
Projector control Displays the projector control screen.
Settings Shows the settings screen.
Projector name The name of the projector on the network
Comment Relevant notes, such as where the projector is installed
MAC address The MAC address of the projector
IP address The IP address of the projector
PowerStatus The power status of the projector
LampModeFullPower Lamp operating time in [Full power] lamp mode
LampModePowerSaver Lamp operating time in [Power saver] lamp mode
LampTimeConverted Lamp operating time (converted value)
FilterTime Air filter operating time
Alert Error message (if an error has occurred)
Temperature abnormality
Faulty lamp
Faulty cooling fan
Faulty air filter unit
Faulty power supply
Faulty lens connector
Unknown error
The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the 
network administrator for the projector IP address. It is possible to check the IP address 
from the projector menu. (P125) 
						

							133
Menu Description
Advanced Guide
Menu Description
4Enter the user name and password on the password input window, then 
click [OK].
The factory default user name is “root” and the password is “system”.
The settings screen is displayed. Complete the network settings on this screen.
■Network Setting
1Select a function to set up from the settings screen menu.
To control the projector from the computer, click [Projector control]. (P146) 
						

							Menu Description
134
2Enter setting details in the fields shown (1), and then click [OK] (2).
3A confirmation window appears. Check the contents and if they are 
correct, click [Apply].
The settings are applied to the projector.
Selecting [Network] or [Password] in the menu will cause this message to be 
displayed: “Save completed. Please change setting and reconnect.”
If you select functions other than above, “Save completed” is displayed. Click 
[Back to top] to return to the top page of the web screen.
(1)
(2) 
						

							135
Menu Description
Advanced Guide
Menu Description
Setting a Password [Password]
From [Password] in the settings screen, you can set a user name and password for 
web screen login. For the setting procedure, refer to “Network Setting” (P133).
ItemExplanationFactory default setting
User name When logging into the web screen, 
enter the user name in 1-byte 
alphanumeric characters and symbols 
(4 -15 characters).root
New password When logging into the web screen, 
enter the password in 1-byte 
alphanumeric characters and symbols 
(4 -15 characters).system
Confirm new password For confirmation, enter the same 
password that you entered in [New 
password].system 
						

							Menu Description
136
Setting Basic Information [Network]
From [Network] in the settings screen, you can log into the web screen and set 
basic network information. For the setting procedure, refer to “Network Setting” 
(P133).
ItemExplanationFactory default setting
MAC address Shows the projector’s MAC address. The MAC address of the 
projector
DHCP Select whether to turn the DHCP 
function on or off. The following settings 
cannot be configured manually when 
this setting is [ON], because the IP 
address is acquired from the server.
[IP address]
[Subnet mask]
[Default gateway]OFF
IP address Enter the IP address of the projector in 
1-byte numbers.192.168.254.254
Subnet mask Enter the subnet mask in 1-byte 
numbers.255.255.255.0
Default gateway Enter the default gateway IP address in 
1-byte numbers.0.0.0.0
If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to 
the network.
If the network subnet mask was changed, select [Subnet mask] in the above screen and 
set the new subnet mask. 
						

							137
Menu Description
Advanced Guide
Menu Description
Specifying Networked Multi-Projection Settings [NMPJ Password]
From [NMPJ Password] in the settings screen, you can specify the items needed 
for NMPJ authentication. For the setting procedure, refer to “Network Setting” 
(P133).
ItemExplanationFactory default setting
Password Enter the password required for a 
networked multi-projection connection 
in single-byte alphanumeric characters 
(0-15 characters).
Confirm password For confirmation, enter the same 
password as you entered in [Password].
For details on Networked Multi-Projection (NMPJ), refer to the NMPJ user’s manual. 
						

							Menu Description
138
Setting Up Email [Mail]
From [Mail] in the settings screen, you can set the items necessary to send error 
mails and test mails. For the setting procedure, refer to “Network Setting” (P133).
* When the interval is set to 0 seconds, repeated attempts to send mail are made 
(as set in [Mail resend times]) without pausing between attempts.
ItemExplanationFactory default setting
To :
Enter the recipient address for error mails 
in 1-byte alphanumeric characters and 
symbols (1 - 63 characters).MailUserAccount
Cc:
Enter the CC address for error mails in 1-
byte alphanumeric characters and symbols 
(1 - 63 characters).
From:
Enter the sender address for error mails 
in 1-byte alphanumeric characters and 
symbols (1 - 63 characters)[email protected]
SMTP server IP address Enter the SMTP server IP address in 1-
byte numbers.0.0.0.0
SMTP server port 
number
Enter the SMTP server port number in 1-
byte numbers (1 - 65535).25
SNTP server IP address Enter the SNTP server IP address in 1-
byte numbers.0.0.0.0
Time zone Select the time zone where the 
projector is used.(GMT) Dublin, Lisbon, 
London
Mail resend interval* Enter the interval for resending mail 
when an error occurred (unit: seconds) 
within the range of 0 - 59 seconds using 
1-byte numbers.10
Mail resend times Enter the number of times to resend 
mail when an error occurred within the 
range of 0 - 255 using 1-byte numbers.3
Error report Select whether to turn the error mail 
sending function on or off.OFF 
						

							139
Menu Description
Advanced Guide
Menu Description
Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings screen, you can configure the settings for 
authentication of mail that is sent when an error occurs. For the setting procedure, 
refer to “Network Setting” (P133).
ItemExplanationFactory default setting
Mail authentication Select the mail authentication method. 
If OFF is selected, the other mail 
authentication settings cannot be 
changed.OFF
User name
Enter the user name to use for mail 
authentication in 1-byte alphanumeric 
characters and symbols (1 - 63 
characters).
Password
Enter the password for mail 
authentication in 1-byte alphanumeric 
characters and symbols (1 - 63 
characters).
Confirm password  For confirmation, enter the same 
password as you entered in 
[Password].
POP3 server IP 
addressEnter the POP3 server IP address in 1-
byte numbers.0.0.0.0
POP3 server port 
numberEnter the POP3 server port number in 
1-byte numbers (1 - 65535).11 0
POP before SMTP 
response time
Enter the SMTP authentication timeout 
period after POP3 authentication (unit: 
milliseconds) using 1-byte numbers (0 - 
9999 milliseconds).300 
						

							Menu Description
140
Sending a Test Mail [Send test mail]
From [Send test mail] in the settings screen, you can send a test mail to the mail 
address that was set in [Mail]. The settings cannot be changed from this screen.
SNMP Settings [SNMP]
From [SNMP] in the settings screen, you can configure the settings related to 
control of projectors which use SNMP (Simple Network Management Protocol). For 
the setting procedure, refer to “Network Setting” (P133).
ItemExplanation
To: The recipient address which was set from [Mail] in the settings screen (P138) is 
displayed.
Cc: The CC address which was set from [Mail] in the settings screen (P138) is 
displayed.
From: The sender address which was set from [Mail] in the settings screen (P138) is 
displayed.
Subject: The predetermined mail title “Canon Projector test” is displayed.