Canon Projector WUX6010 User Manual

							Projection Procedure
71
Basic Guide
Projection Procedure
■Selecting an Image Mode
Press the IMAGE button on the remote control to select.
The image mode changes each time the IMAGE button is pressed. (The displayed 
image modes vary depending on the selected input signal.)
You can also select any image mode from the [Image mode] menu. (P88)
•User settings 1 - 5 are displayed when the desired image settings have been 
created and stored using the user memory function in the image adjustment 
menu. (P88)
Step 7 Turn the Projector Off
1Press the POWER button to display the window shown below.
2When this window is displayed, press the POWER button again to turn off 
the power.
After you turn the power off, the projector will enter standby mode once it cools 
down.
If you want to continue projecting without turning off the power, press a button other than 
POWER, or else wait until the confirmation message disappears.
• After turning off the projector, wait at least 5 minutes before turning it on again. It may 
shorten the lamp life if you turn on the projector immediately after turning it off.
• Using the projector for extended periods may shorten the life of the lamp and internal 
optical components.
• Unplug the projector if it will not be used for an extended period.
Remote control
Remote controlProjector 
						

							72
Convenient Features
This section describes features convenient during presentations and in other 
situations.
Temporarily Blacking Out an Image
Projection can be temporarily blanked after a presentation, or to divert the 
audience’s attention away from the screen.
Press the BLANK button to black out the image.
Press the BLANK button again to show the image.
• You can set the screen state while blacking out the image in the menu. 
(P108)
• The lamp remains illuminated while the image is blacked out.
Freezing the Picture
Projection can be temporarily frozen during computer operations that would be 
distracting, or to pause playback of video or animation.
Press the FREEZE button to freeze the moving image. The 
projector shows the following icon.
Press the FREEZE button again to return to the original display.
• It is also cancelled when the input signal is terminated.
Projecting Images Stored on a USB Flash Drive
Even without using a computer, you 
can project images stored on a USB 
flash drive simply by connecting it to 
the USB port.
For instructions on projection from a 
USB flash drive in the projector’s USB 
port, see “Projecting Images on a USB 
Flash Drive” (P149).
Remote control
Remote control
Screen 
						

							Convenient Features
73
Basic Guide
Convenient Features
Projecting a Test Pattern from the Menu
Even without any input signals, the projector can project a test pattern. Test 
patterns can be projected during installation to check how the projector is installed.
For details on projecting test patterns, see “Install settings” (P95) or “Displayed Test 
Patterns” (P179).
Set Power-Saving Settings
Set power-saving settings as needed.
The following four settings are available. For details, refer to the page describing 
each function.
• Lamp mode (P93)
Adjust lamp and fan power consumption in the image mode.
• Power management mode (P112)
Automatically turns off the lamp or the power after a certain period if the projector 
is idle without an input signal.
• Power management duration (P113)
Specify the period after which the lamp or the projector should go off 
automatically if left idle without an input signal when [Power management mode] 
is set to [Lamp off] or [Standby].
• Network standby settings (P124)
Conserve energy in standby mode, as needed. 
						

							74
Convenient Features
Adjusting the Volume
Useful when:
• You want to adjust the volume level of the projector or external speakers.
Press the VOL button. The following screen appears.
• You can also adjust the volume level with the [ ] / [ ] buttons of the 
projector.
• Adjust the volume or mute setting on the computer if the volume level is too 
low.
• You can also adjust the volume level of the speakers connected via the 
audio output terminal.
Muting the Sound
Useful when:
• You want to temporarily mute unnecessary sound.
• You want to immediately mute the sound.
Press the MUTE button to mute the sound. The projector shows 
the following icon.
Press the MUTE button again to cancel the mute function.
• You can also mute the sound of the speakers connected via the audio output terminal.
Remote control
Remote control
Screen 
						

							Convenient Features
75
Basic Guide
Convenient Features
Zooming Part of an Image
Useful when:
• Zooming in on an object such as a small graph during a presentation (up to 12x).
• Focusing on the current subject.
Press the +D.ZOOM button 
to enlarge a part of the 
image. Press the –D.ZOOM 
button to reduce the image 
size.
• The magnification appears on 
the screen.
You can move the enlarged area by using the 
[ ] / [ ] / [ ] / [ ] buttons.
You can restore the original size of the image by pressing the OK button.
The D.ZOOM buttons work differently than [Zoom] in the [Install settings] menu (P97).
Remote control
Screen
Screen Remote control
Projector 
						

							76 
						

							77
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Connection Procedure
Projection Procedure
Convenient Features
Advanced GuideUsing Menus
Menu Description
Advanced Projection
Other InformationMaintenance
Product Specifications
Troubleshooting
Advanced Guide 
						

							78
Using Menus
Use the menus to set the operation of the projector in detail.
Menu Configuration
The menu screen is divided into 6 tabs as shown below.
[System settings] tab (P107)
You can set the operation of the projector.
[Image adjustment] tab (P87)
You can adjust the image quality and colors 
according to your preference.
[Network settings] tab (P122)
These settings are for when using the projector 
from a PC via a network.
For the network settings, refer to “Network 
settings” (P120).
[Information] tab (P148)
You can check information about the 
signal types of the images projected and 
other information.
[Install settings] tab (P95)
This setting is used when installing the projector.
[Input settings] tab (P81)
You can set the type of signal or the method of 
projection of the images input.
Contents of menuMenu items 
						

							79
Using Menus
Advanced Guide
Using Menus
Basic Menu Operations
1Press the MENU button to display the menu window.
2Press the [ ] / [ ] buttons to select a tab.
•If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to 
move the current selection to the top.
3Press the [ ] / [ ] buttons to select an item.
4Select contents.
How to select the contents varies depending on the item.
Selecting from a list   Example: Aspect (P82)
Remote controlProjector
Remote controlProjector
Remote controlProjector
1. Select [Aspect].
2. Press the OK button or [ ] button 
to display a list of the contents.
3. Use the [ ] / [ ] buttons to select 
the desired contents.
4. When you have found the 
contents you desired, press the 
OK button or [ ]. 
						

							Using Menus
80
Adjusting with the [ ] / [ ] buttons   Example: Contrast (P89)
Selecting from a different screen (1)   Example: Menu position (P104)
Selecting from a different screen (2)   Example: Tracking (P83)
5Pressing the MENU button causes the menu screen to disappear.
1. Select [Contrast].
2. Use the [ ] / [ ] buttons to adjust 
the setting.
1. Select [Menu position].
2. Press the OK button to display a 
different screen.
3. Then follow the instruction on the 
screen.
1. Select [Input signal settings].
2. Press the OK button to display a 
different screen.
3. Select [Tracking].
4. Use the [ ] / [ ] buttons to select 
the setting, then use the [ ] / [ ] 
buttons to select the value.