Canon Projector WUX6010 User Manual

							181
Product Specifications
Other Information
Product Specifications
HDMI/HDBaseT
Connecting to a computer
Connecting with AV equipment
Component
* The specifications in the table above are subject to change without notice.
* This projector does not support any computer output signal with a dot clock of higher than 162 MHz.
* Use a computer cable in which all pins are connected. If the cable is a type in which all pins are not 
connected, the image may not be correctly displayed.1080PsF
(1920 x 1080i)–27.000 24.000
28.125 25.000
33.750 30.000
1920 x 1200 D-WUXGA 74.038 59.950
Resolution (dots) Signal typeHorizontal frequency 
(kHz)Vertical frequency (Hz)
640 x 480 VGA 31.469 59.940
800 x 600 SVGA 37.879 60.317
1024 x 768 XGA 48.363 60.004
1280 x 800 WXGA49.702 59.810
49.306 59.910
1280 x 1024 SXGA  63.981 60.020
1366 x 768 – 47.712 59.790
1400 x 1050 SXGA+64.744 59.948
65.317 59.978
1440 x 900 WXGA+55.935 59.887
55.469 59.901
1600 x 900 – 60.000 60.000
1600 x 1200 UXGA 75.000 60.000
1680 x 1050 WSXGA+64.674 59.883
65.290 59.954
1920 x 1200 WUXGA 74.038 59.950
Signal type Horizontal frequency (kHz) Vertical frequency (Hz)
480p 31.469 59.940
576p 31.250 50.000
720p37.500 50.000
45.000 60.000
1080i28.125 50.000
33.750 60.000
1080p27.000 24.000
56.250 50.000
67.500 60.000
Signal type Horizontal frequency (kHz) Vertical frequency (Hz)
480i 15.734 59.940
480p 31.469 59.940
576i 15.625 50.000
576p 31.250 50.000
720p37.500 50.000
45.000 60.000
1080i28.125 50.000
33.750 60.000
1080p56.250 50.000
67.500 60.000
1080PsF27.000 24.000
28.125 25.000
33.750 30.000 Resolution (dots) Signal typeHorizontal frequency 
(kHz)Vertical frequency (Hz) 
						

							Product Specifications
182
■Projector
Model name WUX6010
Display system RGB liquid crystal system (LCOS) : 3 panels
Optical systemColor separation by dichroic mirror / polarizing beam splitter 
and color composition by prism
Display device
Type Reflective liquid crystal panel (LCOS) : 3 panels
Size / Aspect ratio 0.71 X3 / 16:10
Drive system Active matrix system
Number dots / Total 
number dots2,304,000 (1920 x 1200) x 3 panels / 6,912,000
Projection lens (*1)
Zoom ratio / Focal length / 
F value1.5x / f = 23.0 to 34.5 mm / F1.89 to F2.65
Zooming / Focusing 
systemElectric / Electric
Lens shift (*1) V: -15%  to +55%, H: ±10% Electric
Light source (lamp mode: Full 
power / Power saver)340W / 264W
Image size (projection 
distance) (*1)Size 40 to 600 (1.3 m / 4.6 to 29.0 m / 95.1)
Number of colors 16,770,000 colors (full color)
Brightness (*1) (*2) (*3) 6,000 lumen (in presentation mode)
Contrast ratio (*3)2000:1 (Fully white : fully black, presentation mode, lamp 
control [On])
Ratio of brightness at 
periphery to center (*1) (*3)88%
Speaker 5W monaural x 1
Maximum input resolution 1920 x 1200 dots
Video signals
Analog PC inputWUXGA, WSXGA+, UXGA, WXGA+, SXGA+, SXGA, WXGA, 
XGA, SVGA, VGA
(Scan frequency: Horizontal 15 to 75 kHz, Vertical 50 to 85 Hz)
Digital PC inputWUXGA, WSXGA+, UXGA, WXGA+, SXGA+, SXGA, WXGA, 
XGA, SVGA, VGA
HDMI / HDBaseT inputFrom connected computers:
WUXGA, WSXGA+, UXGA, WXGA+, SXGA+, SXGA, WXGA, 
XGA, SVGA, VGA
From connected AV equipment:
1080p, 1080i, 720p, 576p, 480p
Component video input 1080PsF, 1080p, 1080i, 720p, 576p, 576i, 480p, 480i 
						

							183
Product Specifications
Other Information
Product Specifications
*1When using a Standard Zoom Lens (RS-IL01ST). Varies depending on the type of lens unit.
*2When lamp mode is set to [Full power].
*3Compliance with ISO21118-2012
* 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels 
may stay lit or unlit due to the characteristics of the LCD panel. 
* Using the projector continuously for an extended period of time may accelerate the deterioration of 
optical parts.
Input terminal
DVI-I terminal Analog PC, Digital PC (29-pin DVI connector)
HDMI terminal HDMI (deep color only)
ANALOG PC / 
COMPONENT terminalAnalog PC, Component (mini D-sub 15-pin)
HDBaseT terminalHDBaseT-compatible video/audio, 100BASE-T networking, 
serial communication (RJ-45)
LAN terminal Networked multi-projection (RJ-45) 10BASE-T / 100BASE-T
USB Port JPEG images (USB Mass Storage Class)
CONTROL terminal RS-232C (D-sub 9-pin)
REMOTE terminal Wired remote control (3.5Ø stereo mini jack)
AUDIO IN terminal Audio signal (3.5Ø stereo mini jack x 2)
AUDIO OUT terminal Audio signal (3.5Ø stereo mini jack)
Input signal
Digital PC TMDS (Transition Minimized Differential Signaling)
Analog PC0.7Vp-p, positive polarity, impedance = 75Ω
Horizontal / vertical synchronization: TTL level, negative or 
positive polarity
Composite synchronization in G signal: 0.3Vp-p, negative 
polarity, impedance = 75Ω
Component videoCOMPONENT: Separate Y Cb/Pb Cr/Pr signal
Y: 1Vp-p, negative synchronization, impedance = 75Ω
Cb/Pb: 0.7Vp-p, impedance = 75Ω
Cr/Pr: 0.7Vp-p, impedance = 75Ω
Audio Impedance = 47kΩ or more
Noise (lamp mode: Full power / 
Power saver)40dB / 36dB
Operating temperature 0°C (32°F) to 40°C (104°F)
Power supply AC100V to 240V  50 / 60Hz
Power consumption
Full power 465W
Power saver 370W
Standby
Networking and 
HDBaseT off0.3W
Low-power networking 
on, HDBaseT off0.7W
Networking off, 
HDBaseT on1.6W
Low-power networking 
and HDBaseT on1.8W
Dimensions380 mm (W) x 170 mm (H) x 430 mm (D) / 15.0 (W) x 6.7 (H) x 
16.9 (D) in (including the projection)
Weight 8.5 kg / 18.7 lbs (not including projection lens unit)
AccessoriesRemote control, remote control dry-cell batteries, power cord, 
PC cable, Important Information, User’s Manual (CD-ROM) 
and Warranty Card Model name WUX6010 
						

							Product Specifications
184
■Remote Control
■Specification of Each Lens Unit (Option)
For details about the amount of lens shift, refer to “Lens Shift Function” on page 47.
Type RS-RC04 RS-RC05 (Option)
Power supplyDC 3.0V, using two AAA-size 
batteriesDC 3.0V, using two AA-size batteries
Operating range Approx. 8 m± 25° horizontal and vertical (to infrared remote receiver)
Dimensions43 mm (W) x 23 mm (H) x 
135 mm (D) /
 1.7 (W) x 0.9 (H) x 5.3 (D) in.51 mm (W) x 28 mm (H) x 
176 mm (D) /
 2.0 (W) x 1.1 (H) x 6.9 (D) in.
Weight 56 g / 2.0 oz 100 g / 3.5 oz
Name Standard Zoom Lens Long Zoom Lens
Model numberRS-IL01ST RS-IL02LZ
External View
Focal length23.0 - 34.5 mm
(0.9 - 1.4)34.0 - 57.7 mm
(1.3 - 2.3)
F number1.89 - 2.65 1.99 - 2.83
Width97.4 mm (3.8) 97.4 mm (3.8)
Height106.5 mm (4.2) 106.5 mm (4.2)
Length173.4 mm (6.8) 173.4 mm (6.8)
Weight550 g (1.2 lbs) 755 g (1.7 lbs)
Zoom ratio1.5x 1.7x
Projection 
distance1.3 - 29.0 m
(4.3 - 95.1)1.9 - 48.5 m
(6.2 - 159.1)
Size 100 
projection 
distance3.2 - 4.8 m
(10.5 - 15.7)4.7 - 8.0 m
(15.4 - 26.2) 
						

							185
Product Specifications
Other Information
Product Specifications
For details about the amount of lens shift, refer to “Lens Shift Function” on page 47.
Name Short Fixed Lens Ultra Long Zoom Lens
Model numberRS-IL03WF RS-IL04UL
External View
Focal length12.8 mm (0.5) 53.6 - 105.6 mm (2.1 - 4.2)
F number2.0 2.34 - 2.81
Width97.4 mm (3.8) 97.4 mm (3.8)
Height106.5 mm (4.2) 106.5 mm (4.2)
Length175.2 mm (6.9) 184.2 mm (7.3)
Weight910 g (2.0 lbs) 940 g (2.1 lbs)
Zoom ratio– 1.95x
Projection 
distance0.7 - 5.2 m (2.3 - 17.1) 4.6 - 89.0 m (15.1 - 292.0)
Size 100 
projection 
distance1.7 m (5.6) 7.6 - 14.9 m (24.9 - 48.9)
Name Wide Zoom Lens
Model numberRS-IL05WZ
External View
Focal length15.6 - 23.3 mm (6.0 - 9.0)
F number2.09 - 2.34
Width97.4 mm (3.8)
Height106.5 mm (4.2)
Length180.3 mm (7.1)
Weight905 g (2.0 lbs)
Zoom ratio1.5x
Projection 
distance0.9 - 19.5 m (3.0 - 64.0)
Size 100 
projection 
distance2.2 - 3.2 m (7.2 - 10.5) 
						

							Product Specifications
186
■External View
53 mm (2.1)
128 mm (5.0)
212 mm (8.35)234.5 mm (9.2) 92 mm (3.6)
91 mm (3.6)
150 mm (5.9)
311 mm (12.2)
154.5 mm (6.1)
141.5 mm (5.6)
170 mm (6.7)
430 mm (16.9)
380 mm (15.0)
WUX6010
Bolt holes (M4 x 6) for 
installation of ceiling 
attachment 
						

							187
Product Specifications
Other Information
Product Specifications
■ANALOG PC-2 / COMPONENT Terminal
This terminal is used as a computer ANALOG PC input or COMPONENT input 
terminal. Use a D-sub computer cable.
The terminal specifications for the ANALOG PC input and COMPONENT input are 
the same.
Mini D-sub 15-pin
■Service Port (CONTROL)
Pin assignment
Communication format
Communication mode : RS-232C, asynchronous, half-duplex communication
Communication speed : 19200bps
Character length : 8 bits
Stop bits : 2 bits
Parity : None
Flow control : None
The service port is not available when [HDBaseT] is set to [On] and [Serial 
communication] is set to [HDBaseT].
Pin No. Signal Pin No. Signal
1 R 9 +5 V power
2G 10Ground 
(Vertical sync.)
3 B 11 Ground
4OPEN 12DDC data
5Ground 
(Horizontal sync.)13 Horizontal sync.
6 Ground (R) 14 Vertical sync.
7 Ground (G) 15 DDC clock
8 Ground (B)
Pin No. Signal
1OPEN
2RxD
3TxD
4OPEN
5GND
6OPEN
7 Internal pull-up
8OPEN
9OPEN 
						

							Product Specifications
188
User commands
Commands ASCII representation Binary representation
Power supplyPower on POWER=ON 50h 4Fh 57h 45h 52h 3Dh 4Fh 4Eh 0Dh
Power off POWER=OFF50h 4Fh 57h 45h 52h 3Dh 4Fh 46h 46h 
0Dh
Power status 
acquisitionGET=POWER47h 45h 54h 3Dh 50h 4Fh 57h 45h 52h 
0Dh
Input sourceHDMI INPUT=HDMI49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh 
49h 0Dh
Digital PC INPUT=D-RGB49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h 
47h 42h 0Dh
Analog PC-1 INPUT=A-RGB149h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 
47h 42h 31h 0Dh
Analog PC-2 INPUT=A-RGB249h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 
47h 42h 32h 0Dh
Component INPUT=COMP49h 4Eh 50h 55h 54h 3Dh 43h 4Fh 4Dh 
50h 0Dh
LAN INPUT=LAN49h 4Eh 50h 55h 54h 3Dh 4Ch 41h 4Eh 
0Dh
USB INPUT=USB49h 4Eh 50h 55h 54h 3Dh 55h 53h 42h 
0Dh
HDBaseT INPUT=HDBT49h 4Eh 50h 55h 54h 3Dh 48h 44h 42h 
54h 0Dh
Input source 
acquisitionGET=INPUT47h 45h 54h 3Dh 49h 4Eh 50h 55h 54h 
0Dh
Image ModeStandard IMAGE=STANDARD49h 4Dh 41h 47h 45h 3Dh 53h 54h 41h 
4Eh 44h 41h 52h 44h 0Dh
Presentation IMAGE=PRESENTATION49h 4Dh 41h 47h 45h 3Dh 50h 52h 45h 
53h 45h 4Eh 54h 41h 54h 49h 4Fh 4Eh 
0Dh
VividPhoto IMAGE=VIVID_PHOTO49h 4Dh 41h 47h 45h 3Dh 56h 49h 56h 
49h 44h 5Fh 50h 48h 4Fh 54h 4Fh 0Dh
Photo/sRGB IMAGE=PHOTO_SRGB49h 4Dh 41h 47h 45h 3Dh 50h 48h 4Fh 
54h 4Fh 5Fh 53h 52h 47h 42h 0Dh
Dynamic IMAGE=DYNAMIC49h 4Dh 41h 47h 45h 3Dh 44h 59h 4Eh 
41h 4Dh 49h 43h 0Dh
Video IMAGE=VIDEO49h 4Dh 41h 47h 45h 3Dh 56h 49h 44h 
45h 4Fh 0Dh
Cinema IMAGE=CINEMA49h 4Dh 41h 47h 45h 3Dh 43h 49h 4Eh 
45h 4Dh 41h 0Dh
User 1 IMAGE=USER_149h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 
52h 5Fh 31h 0Dh
User 2 IMAGE=USER_249h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 
52h 5Fh 32h 0Dh
User 3 IMAGE=USER_349h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 
52h 5Fh 33h 0Dh
User 4 IMAGE=USER_449h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 
52h 5Fh 34h 0Dh
User 5 IMAGE=USER_549h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 
52h 5Fh 35h 0Dh
Image mode 
acquisitionGET=IMAGE47h 45h 54h 3Dh 49h 4Dh 41h 47h 45h 
0Dh 
						

							189
Product Specifications
Other Information
Product Specifications
BrightnessBrightness 
value settingBRI= 42h 52h 49h 3Dh  0Dh
Brightness 
acquisitionGET=BRI 47h 45h 54h 3Dh 42h 52h 49h 0Dh
SharpnessSharpness 
value settingSHARP=53h 48h 41h 52h 50h 3Dh  0Dh
Sharpness 
acquisitionGET=SHARP47h 45h 54h 3Dh 53h 48h 41h 52h 50h 
0Dh
ContrastContrast value 
settingCONT=43h 4Fh 4Eh 54h 3Dh  
0Dh
Contrast 
acquisitionGET=CONT 47h 45h 54h 3Dh 43h 4Fh 4Eh 54h 0Dh
AspectAuto ASPECT=AUTO41h 53h 50h 45h 43h 54h 3Dh 41h 55h 
54h 4Fh 0Dh
4:3 ASPECT=4:341h 53h 50h 45h 43h 54h 3Dh 34h 3Ah 
33h 0Dh
16:9 ASPECT=16:941h 53h 50h 45h 43h 54h 3Dh 31h 36h 
3Ah 39h 0Dh
16:10 ASPECT=16:1041h 53h 50h 45h 43h 54h 3Dh 31h 36h 
3Ah 31h 30h 0Dh
Zoom ASPECT=ZOOM41h 53h 50h 45h 43h 54h 3Dh 5Ah 4Fh 
4Fh 4Dh 0Dh
True size ASPECT=TRUE41h 53h 50h 45h 43h 54h 3Dh 54h 52h 
55h 45h 0Dh
Aspect value 
acquisitionGET=ASPECT47h 45h 54h 3Dh 41h 53h 50h 45h 43h 
54h 0Dh
Lamp modeFull power LAMP=FULL4Ch 41h 4Dh 50h 3Dh 46h 55h 4Ch 4Ch 
0Dh
Power saver LAMP=ECO 4Ch 41h 4Dh 50h 3Dh 45h 43h 4Fh 0Dh
Lamp mode 
value 
acquisitionGET=LAMP 47h 45h 54h 3Dh 4Ch 41h 4Dh 50h 0Dh
BlankBlank On BLANK=ON 42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 4Eh 0Dh
Blank Off BLANK=OFF42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 46h 46h 
0Dh
Blank 
acquisitionGET=BLANK47h 45h 54h 3Dh 42h 4Ch 41h 4Eh 4Bh 
0Dh
Commands ASCII representation Binary representation 
						

							190
Troubleshooting
LED Indicator Details
When there is a problem with the projector, the LED indicator on the side of the 
projector illuminates or flashes continuously after the projector is turned off.
• Wait until the cooling fan stops and disconnect the power plug from the electrical outlet before 
dealing with the problem.
LED indicator 
statusMeaning Cause and countermeasure
WARNING and 
TEMP are lit.Temperature 
abnormalityThe temperature inside the projector is too high for 
some reason or the outside air temperature is 
higher than the operating range. If the problem is 
inside the projector, check whether the projector is 
installed and operating normally, unplug the 
projector from the power outlet to cool down the 
projector interior and then restart projection. If the 
air intake or exhaust vent is blocked, remove the 
obstacle. If the air filter is clogged, clean or replace 
it. (P163, P164) If the same warning occurs again, 
there may be a malfunction in the projector. 
Contact the Canon Customer Support Center.
WARNING and 
LAMP are lit.Faulty lamp The lamp does not illuminate. If the lamp does 
not illuminate, replace it. (P165) If the same 
warning occurs again, there may be a 
malfunction in the lamp drive circuit. Contact the 
Canon Customer Support Center.
WARNING 
flashes 3 times, 
LAMP is lit.Faulty lamp 
coverThe lamp cover is open. Unplug the projector 
from the power outlet, then install the lamp cover 
correctly and turn on the projector again.
If the lamp cover has been installed properly, 
there may be a malfunction in the lamp cover 
detection switch. Contact the Canon Customer 
Support Center.
WARNING 
(only) flashes 4 
times 
repeatedly.Faulty 
cooling fanThere may be a malfunction in the cooling fan or 
another component. Unplug the projector from 
the electrical outlet, then plug it back into the 
outlet and turn on the projector again. Contact 
the Canon Customer Support Center if the same 
warning occurs again.
WARNING 
(only) flashes 5 
times 
repeatedly.Faulty power 
supplyAbnormal voltage is applied to some parts in the 
power supply or another failure may have 
occurred. Unplug the projector from the electrical 
outlet, then plug it back into the outlet and turn on 
the projector again. Contact the Canon Customer 
Support Center if the same warning occurs 
again.