Canon Projector WUX6010 User Manual

							21
Before Installation
Before Installation
■When Using Mounted on the Ceiling
When the projector is used mounted on the 
ceiling or installed in a high location, it is 
necessary to periodically clean the air 
intake and exhaust vents, and the area 
around the air filter. Dust that accumulates 
in intake or exhaust vents may impair 
ventilation, raising the temperature inside 
and posing a risk of damage or fire. Use a 
vacuum cleaner or similar means to 
remove dust from the intake vent and 
exhaust vent. 
						

							Before Installation
22
■Install Facing in the Correct Direction
When installing the projector facing upward or downward, specify which way the projector 
is facing in [Install settings] > [Professional settings] > [Vertical projection]. (P99)
• The projector can be installed facing any direction*1, as shown 
below. However, projection upward or downward may shorten the 
useful life of the lamp. [Install settings] of the projector must also 
be adjusted. Specifically, for upward or downward projection, refer 
to instructions for [Vertical projection] (P99) in the [Install settings] 
menu.
• Do not attempt to install the projector for upward or downward 
projection by yourself. Always request installation by a qualified 
technician or the Canon Customer Support Center.
*1 No optional accessories are available for installing the projector in 
ways other than ceiling installation (P41, P199).
*2 An inclination of more than 10 degrees may damage the lamp.
Upward 
projection:
Inclination of the 
projector should 
be no more than 
10° from the 
vertical axis.*
2
Downward 
projection:
Inclination of the 
projector should 
be no more than 
10° from the 
vertical axis.
*2
If installing the projector 
on the floor or hanging 
from the ceiling, the left / 
right inclination of the 
projector should be no 
more than 10°.*
2
Do not use the 
projector standing 
on its side. 
This may 
damage the lamp.*210°10° 10° 10° 10°
10° 
						

							23
Before Installation
Before InstallationCopyright Notice
Please note that enlarging or reducing the size of an image for commercial 
purposes or public presentation may infringe on the legally protected copyright 
or the copyright holder of the original material.
Ensure Network Security
Take measures to ensure network security. Note that Canon is not liable in any 
way for direct or indirect loss from network security incidents, such as 
unauthorized access.
Examples of Security Measures
•Use in an intranet environment.
•Assign a private IP address.
•Use behind a firewall.
•Change passwords regularly.
About Trademarks
•Ethernet is a registered trademark of Xerox Corporation.
•Microsoft, Windows, Windows Vista, Windows 7, Windows 8 and 
Windows 8.1 are registered trademarks or trademarks of Microsoft 
Corporation in the United States and / or other countries.
•Mac, Mac OS and Macintosh are trademarks of Apple Inc., registered in the 
United States and / or other countries.
•HDMI, the HDMI logo and High-Definition Multimedia Interface are 
trademarks or registered trademarks of HDMI Licensing, LLC.
•PJLink is a registered trademark of JBMIA and pending trademark in some 
countries.
•PJLink is a registered trademark, or an application has been submitted for 
trademark, in Japan, the United States and / or other countries or regions.
•AMX is a trademark of AMX Corporation.
•Crestron®, Crestron RoomView®, and Crestron Connected™ are registered 
trademarks of Crestron Electronics, Inc.
•HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT 
Alliance.
•All other trademarks are the property of their respective owners. 
						

							24
Open Source Software
The product contains Open Source Software modules. For details, refer to the third-
party software license file “Third-Party Software” in the License folder of the user’s 
manual CD-ROM. Each module’s license conditions are also available in the same 
folder.
■Software under the GNU General Public License Version 2
Contained programs are free software; you can redistribute them and/or modify 
them under the terms of the GNU General Public License attached to each copy of 
the program.
Each program is distributed in the hope that it will be useful, but WITHOUT ANY 
WARRANTY; without even the implied warranty of MERCHANTABILITY or 
FITNESS FOR A PARTICULAR PURPOSE. Please see “NO WARRANTY” and 
“NO SUPPORT” stated below.  For more detail, please see full text of the GNU 
General Public License.
NO WARRANTY
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO 
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY 
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE 
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM 
“AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR 
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE 
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM 
IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME 
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN 
WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY 
MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE 
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, 
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR 
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS 
OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED 
BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE 
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY 
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 
NO SUPPORT
Canon Inc., and all its subsidiaries or its dealers do not make any support service 
regarding the source code. Canon Inc., and all its subsidiaries or its dealers shall 
not respond to any questions or enquiries, from you or any other customers, 
regarding the source code. 
						

							25
Before Use
Before Use
Projector Highlights
High-Resolution LCOS Projection
Projection at 1920x1200 (WUXGA), thanks to high-resolution reflective liquid 
crystal on silicon (LCOS) panels.
HDBaseT Input
The projector supports HDBaseT, a next-generation connectivity standard. 
HDBaseT offers a convenient connection for carrying high-quality video and audio 
signals equivalent to HDMI across distances up to 100 m over a single LAN cable.
This port can also be used to connect the projector to a network. 
(P50, P51, P 111, P112, P120)
Lens Shift
Lens shift enables motorized image repositioning up, down, left, or right (P47) for 
greater freedom in installation.
Motorized Zoom and Focus Adjustment
Efficient setup using motorized zoom and focus adjustment.
Five Lens Units Available
Choose the optimal lens unit for the projection distance or purpose.
HDBaseT terminalLAN cable
(CAT5e or better; 
shielded; not included)HDMI cable, etc.
HDBaseT transmitter 
						

							Before Use
26
Split-Screen Display
Splits the screen for projection of 
two separate input signals at once. 
(P153) 
Edge Blending
Blend the overlapping edges of images 
from multiple projectors to make the 
overall image more seamless. (P154) 
Networked Multi-Projection (NMPJ) 
Project images from multiple computers via a network connection.
For details on Networked Multi-Projection (NMPJ), refer to the NMPJ user’s 
manual.
LAN 
						

							27
Before Use
Before Use
Included Accessories
Before use, make sure the following items are included in the package.
• Remote control• Batteries for the remote control
(AAA size x2)
(part No.: RS-RC04)
Optional remote controls are also 
available (RS-RC05). The RS-RC05 
can also be used as a wired remote. 
(P37)
• Computer cable (1.8 m / 5.9)
(mini D-sub 15-pin / mini D-sub 15-pin)• Power cord 
(1.8 m / 5.9)For Continental 
Europe
• User’s Manual (CD-ROM) For the U.S.A. 
and Canada
• Warranty Card • Important Information 
						

							Before Use
28
Part Names
Projector
■Rear Side
Terminals and 
connectorsInfrared remote receiver 
(P37)Lens unit (sold separately)
Air intake vent Power cord connector (P52)
Side control (P29)
Air filter frame (P164)
Anti-theft lock hole
An anti-theft wire cable (not included) can be connected.
Do not block the air intake.
Doing so may cause a 
malfunction.
Exhaust vent
Infrared remote receiver (P37)
Do not block the air exhaust. 
Doing so may cause a 
malfunction.
Lamp cover 
						

							29
Before Use
Before Use
■Bottom Side
Side Control
Adjustable feet (P40)Bolt holes for installation of 
ceiling attachment
(1) POWER button (P53, P71)
Turns the projector on or off.
(2) MENU button (P78)
Displays a menu on the screen.
(3) LENS button
Each time the button is pressed, 
the screen changes to focus 
adjustment (P59), zoom (image 
size) adjustment (P60), or lens shift 
(image position) adjustment (P61). 
To adjust, use the [ ] / [ ] or the 
[ ] / [ ] buttons.(4) INPUT button (P56)
Switches the input signal.
(5) Pointer / VOL buttons (P79)
Up, down, left, or right in menu 
navigation or other operations.
Adjust the sound volume.
[ ] VOL+ button: Increases the 
volume.
[ ] VOL– button: Decreases the 
volume.
Selects the upper, lower, left or 
right item in the menu.
(6) OK button (P79)
Determines the item selected from 
the menu.
(1)
(2) (4) (5)(6)(3) 
						

							Before Use
30
LED Indicators
The projector status is shown by the LED indicators (off / lit / flashing).
•POWER ON (green) : Lights up or flashes under normal conditions when the 
power is on.
•STAND BY (red) : Lights up or flashes during standby or when the projector 
is shut down.
•WARNING (red) : Lights up or flashes when an error occurs.
•LAMP (orange) : Lights up or flashes when a problem occurs with the lamp 
or lamp cover.
•TEMP (red) : Lights up or flashes when the internal temperature is 
high.