Canon Projector WUX5000 User Manual
Have a look at the manual Canon Projector WUX5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
71 Adjusting the Image User’s ManualProjectin g an Ima ge Adjusting the Image Size The size of the projected image can be adjusted by pressing the ZOOM button on the remote control or the LENS button on the projector. Change the projector installation posi- tion if your desired image is too large or too small to adjust it with the zoom function. (P156) 1Press either the ZOOM button on the remote control or the LENS button on the projec- tor twice in order to display the window shown below. Push twice Remote controlProjectorRemote control
Adjusting the Image 72 2Press the pointer buttons to adjust the image size. 3When the desired image size is selected, press the OK button or the ZOOM button. When the Short Fixed Lens (RS-IL03WF) is attached, zoom adjustment cannot be performed. Use the [] button on the remote control, or the UP button on the projector to increase the image size. Use the [] button on the remote control, or the DOWN button on the projector to decrease the image size. Remote controlProjectorRemote control Screen
73 Adjusting the Image User’s ManualProjectin g an Ima ge Adjusting the Focus To adjust the focus, press the FOCUS button on the remote control or the LENS button on the projector. For the projection distances of the lens unit, refer to page 156. 1Press either the FOCUS button on the remote control or the LENS button on the pro- jector in order to display the window shown below. 2Press the pointer buttons to adjust the focus. 3When the focus is adjusted optimally, press the OK button or the FOCUS button. Remote controlProjectorRemote control Use the [] button on the remote control, or the UP button on the projector to adjust the focus position. Use the [] button on the remote control, or the DOWN button on the projector to per- form fine adjustment. Remote controlProjectorRemote control
Adjusting the Image 74 Adjusting the Image Position To adjust the screen position up, down, left, or right, press the LENS-SHIFT button (WUX5000 / WUX4000) or SHIFT button (WX6000 / SX6000) on the remote control, or the LENS button on the projector. This function is referred to as “lens shift”. It can change the projected screen to the most suitable position by moving the position of the lens up/down/ left/right. (P160) 1Press either the LENS-SHIFT button (WUX5000 / WUX4000) or the SHIFT button (WX6000 / SX6000) on the remote control, or the LENS button on the projector 3 times in order to display the window shown below. * If the Short Fixed Focus Lens (RS-IL03WF) is attached, when the LENS button on the projector is pressed twice, the window below will be displayed. The available range for lens shift (percentage of movement relative to the screen size) var- ies depending on the lens unit which is used. (P161) There are areas where each lens is unable to move. With the Short Fixed Lens (RS- IL03WF), the areas are at the four corners and for the other lenses, the areas are at the top left and bottom right. (P161) Push three times* Remote controlProjector Remote control
75 Adjusting the Image User’s ManualProjectin g an Ima ge 2Press the pointer buttons to adjust. 3When the desired position is reached, press the OK button. ■Resetting the Position The lens position after movement with the lens shift function is not returned when the power is turned off. To return it to its original position, perform reset. During screen position adjustment, press and hold the LENS-SHIFT button (WUX5000 / WUX4000) or SHIFT button (WX6000 / SX6000) on the remote control, or the LENS button on the projector to display the [Lens shift Reset] window. The selections for the lens currently used are displayed. Use the pointer buttons to select one of them, then press the OK button. Lens unit typeAvailable items Standard Zoom Lens RS-IL01ST 50% (Home position) : Up 50%, left / right 0% 0% : Up / down / left / right 0%Long Zoom Lens RS-IL02LZ Ultra Long Zoom Lens RS-IL04UL Short Fixed Lens RS-IL03WF0% (Home position) : Up / down / left / right 0% Remote control Projector Screen Remote control
Adjusting the Image 76 Adjusting Keystone Distortion The D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button (WX6000 / SX6000) can be used to correct keystone distortion. 1Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button (WX6000 / SX6000) to display the window in the center illustration below. Keystone can be adjusted within the range of ±20 degrees. If the keystone distortion is too large to adjust, move the projector installation position so that it is completely straight. The result of keystone adjustment is stored in memory. If you place the projector in the same position, the keystone adjustment is not necessary. Signals are processed digitally when keystone distortion is corrected. The image may look different from the original one. In addition, the aspect ratio of the image may change. Perform keystone distortion correction with the lens shift position in the home position. Cor- rection will not be performed correctly if the position is not the home position. Remote controlRemote control
77 Adjusting the Image User’s ManualProjectin g an Ima ge 2Press the pointer buttons to adjust. 3When keystone distortion has been corrected, press the OK button. ■Resetting the Keystone Adjustment Perform the following steps to reset the keystone adjustment. Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button (WX6000 / SX6000) twice to display the [Keystone reset] window. Then, select [OK] with the [ ] button, and press the OK button. Remote control Projector [ ] button Reduces the dimensions of the upper edge[ ] button Reduces the dimensions of the lower edge [] button Reduces the dimension of the left edge[ ] button Reduces the dimension of the right edge Screen Remote control
78 Selecting an Image Mode You can select an image mode to suit the projected image. In each image mode, you can further adjust the brightness, contrast, sharpness, gamma, color adjustment, advanced adjustment, and lamp mode (WUX4000). (P109) ■Image Modes The image modes which can be selected vary somewhat depending on the selected input signal. Image Mode Compatible input signals Explanation Digital PC Analog PC (WUX5000 / WUX4000)Analog PC-1, 2 (WX6000 / SX6000) HDMI (when [HDMI In] is [Computer]) Component HDMI (when [HDMI In] is [Auto]) StandardSuitable for projecting a computer screen or watching media played with video software in a brightish room. This image mode emphasizes white tones. Presenta- tionSuitable for viewing text-based images in a brightish room. DynamicSuitable for watching media played with video software in a brightish room. VividPhotoSuitable for viewing images with vibrant colors in a moderately dark room. This image mode emphasizes color saturation. Photo/ sRGBSuitable for viewing images taken with a digital camera that supports sRGB in a moderately dark room. This image mode supports the sRGB standard. VideoSuitable for watching video taken with a video camera in a moderately dark room. CinemaSuitable for watching media played with video software in a dark room. This image mode enables viewers to enjoy the atmosphere of a movie the- ater. User 1 - 5 * ** Up to 5 user-selected combinations of image quality settings can be stored in the memory. (P110) Stored settings can be selected as an image mode. : Compatible : Not compatible
79 Selecting an Image Mode User’s ManualProjectin g an Ima ge ■How to Select an Image Mode Press the IMAGE button on the remote control to select. The image mode changes each time the IMAGE button is pressed. (The displayed image modes vary depending on the selected input signal.) You can also select any image mode from the [Image mode] menu. (P109) User settings 1 - 5 are displayed when the desired image settings have been created and stored using the user memory function in the image adjustment menu. (P110) Remote control
80 Turning Off the Projector 1Press the POWER button to display the window shown below. When this window is displayed, press the POWER button again to turn off the power. The lamp goes off, the [STAND BY] indicator starts flashing in red and the cooling process starts. 2Disconnect the power cord from the electrical outlet. If the power plug is left connected, the [STAND BY] indicator will switch from flashing to constantly illuminated after the cooling process is completed. You cannot turn the projector on while the cooling process is in operation. If you want to continue projecting without turning off the power, press a button other than POWER, or else wait until the confirmation message disappears. After turning off the projector, wait at least 5 minutes before turning it on again. It may shorten the lamp life if you turn on the projector immediately after turning it off. Using the projector for a long time may shorten the life of the lamp and internal optical components. Remote control ProjectorRemote control