Home > Canon > Projector > Canon Projector WUX5000 User Manual

Canon Projector WUX5000 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Canon Projector WUX5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							131
    Setting Various Functions
    User’s ManualSettin
    g Functions from Menus
    Lens Shift Reset
    [Lens shift Reset]
    Resets the lens shift (P74) setting to the 
    standard position.
    MENU > [System settings] > [Other settings] > 
    [Lens shift Reset]
    MENU > [Install settings] > [Lens shift Reset]
    Select [Lens shift Reset] and press the OK 
    button. The following screen for confirma-
    tion appears.
    Use the [ ]
     / [ ] buttons to select the 
    standard position, and then select OK.
     The standard position varies depending 
    on the type of lens unit used. For details, 
    refer to page 75.
     The position which was adjusted by lens 
    shift does not change when the power is 
    turned off.
    HDMIComponent
    Digital PCAnalog PC 
    						
    							Setting Various Functions
    132
    Extending the Menu Dis-
    play Time
    [Menu display time]
    The setting for the menu display time can 
    be extended from the normal 10 or 30 sec-
    onds to 3 minutes. For the WUX5000 / 
    WUX4000, if [Extended] is set, when push-
    ing and holding a button on the projector or 
    remote control, the same key repeat func-
    tion will be enabled as when pressing a 
    button repeatedly.
    MENU > [System settings] > [Other settings] > 
    [Menu display time]
    MENU > [Install settings] > [On screen] > [Menu 
    display time]
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     [Normal] is the factory default.
     The following display and operation are also 
    changed.
    *1 WUX4000
    *2 WX6000 / SX6000HDMIComponent
    Digital PCAnalog PC
    NormalThe menu is displayed for 10 or 30 sec-
    onds.
    ExtendedThe menu is displayed for 3 minutes. 
    Item [Normal] [Extended]The display time of the following 
    screens
    -MENU screen
    -Input (P60)
    -Zoom adjustment (P71)
    -Focus adjustment (P73)
    -Keystone adjustment (P76)
    -Keystone reset (P77)
    -D.image shift adjustment (P67, P68)
    -D.image shift reset (P69)
    -Aspect (P70)
    -Image mode (P78)
    -Volume adjustment (P83)
    -Lamp mode (P119) *1
    -Lens shift (P74)
    -Lens shift reset (P131)
    10 / 30 
    seconds3 minutes
    Press-and-hold operation of 
    pointer buttons other than for 
    [Zoom adjustment], [Focus 
    adjustment], and [Lens shift]
    Press-and-hold operation of VOL buttonPress-and-hold operation of the 
    D.ZOOM buttonEnabled Disabled
    Key repeat *2 [On] [Off] 
    						
    							133
    Setting Various Functions
    User’s ManualSettin
    g Functions from Menus
    Showing / Hiding the High 
    Temperature Warning Icon
    [Overheat Warning Display]
    You can select whether or not to display 
    the [High temperature warning] icon when 
    the temperature inside the projector has 
    increased and is approaching the overheat 
    temperature.
    MENU > [System settings] > [Other settings] > 
    [Overheat Warning Display]
    MENU > [Install settings] > [On screen] > [Over-
    heat warning display]
    Press the OK button to accept your setting 
    and then press the  MENU button or EXIT 
    button (WX6000 / SX6000).
    When [On] is set, the [High temperature 
    warning] icon shown below will be dis- played when the temperature inside the 
    projector is abnormally high.
    • [Off] is the factory default.
    HDMIComponent
    Digital PCAnalog PC
    Off The [High temperature warning] icon is 
    not displayed.
    On The [High temperature warning] icon is 
    displayed.
    Screen 
    						
    							Setting Various Functions
    134
    Reducing Flickering
    [Deflicker]
    This function adjusts the image display in 
    order to reduce flickering in the projected 
    image.
    MENU > [System settings] > [Other settings] > 
    [Deflicker]
    • When deflicker is performed, the image adjustment screen is projected for approx-
    imately 20 seconds.
     To cancel deflicker, press the  POWER but-
    ton.
    Gamma Restore
    [Gamma restore]
    The gamma characteristic of the LCD 
    panel inside the projector can be cor-
    rected.
    MENU > [System settings] > [Other settings] > 
    [Gamma restore]
     If Gamma restore is performed, the pro- jected image will be adjusted for a period 
    of approximately 150 seconds.
     To stop Gamma restore, press the  POWER 
    button or the  EXIT button (WX6000 / 
    SX6000).
    HDMIComponent
    Digital PCAnalog PC
    Off Deflicker adjustment is not per-
    formed.
    Adjust Select [Deflicker] to adjust. The fol-
    lowing screen appears.
    OK Deflicker is performed.
    Cancel Deflicker is not performed.
     Deflicker can only be used when the 
    lamp has been on for approximately 
    30 minutes or longer.
     Be aware that deflicker may be  unable to eliminate flickering in some 
    cases. 
    HDMIComponent
    Digital PCAnalog PC
    Off Returns to the factory default with-
    out performing Gamma restore.
    Adjust Performs Gamma restore and 
    applies the result.
    OK Gamma Restore is per-
    formed.
    Cancel Gamma Restore is not 
    performed.
     Gamma restore can be performed 
    once approximately 30 minutes have 
    elapsed after the lamp flashes.
     Be aware that if Gamma restore  adjustment is performed, the color 
    quality of the projected image may 
    be changed. 
    						
    							135
    Setting Various Functions
    User’s ManualSettin
    g Functions from Menus
    Lamp Warning Display
    [Lamp warning display]
    A message that advises you to change the 
    lamp can be set to display when the lamp 
    has been used for the specified period of 
    time.
    MENU > [Install settings] > [On screen] > [Lamp 
    warning display]
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     The factory default is [On].
     Regardless of the [Lamp warning display] 
    setting, when the lamp replacement time has 
    been reached, the LAMP indicator on the 
    projector will flash.
    Resetting the Lamp 
    Counter
    [Lamp counter]
    You can reset the lamp counter that indi-
    cates the time for lamp replacement.
    MENU > [System settings] > [Other settings] > 
    [Lamp counter]
    MENU > [System settings] > [Other settings] > 
    [Lamp counter]
    HDMIComponent
    Digital PCAnalog PC
    OffThe lamp warning display is not 
    displayed.
    OnThe prepare lamp message and 
    the lamp warning display are dis-
    played.HDMIComponent
    Digital PCAnalog PC
    Do not reset the lamp counter except
    when you have replaced the lamp.
    Otherwise, the lamp counter cannot
    indicate the correct timing for replac-
    ing the lamp.
    For details of lamp replacement, refer
    to page 195. 
    						
    							Setting Various Functions
    136
    Select [Lamp counter] and press the OK 
    button to display the lamp counter.
    Select [Reset] and press the OK button.
    Select [OK] on the screen for confirmation 
    and press the OK button to reset the lamp 
    counter.
    Press the MENU button or EXIT button 
    (WX6000 / SX6000).
    ■About the Display of the Lamp 
    Counter
    The lamp counter displays the hours of 
    use of the lamp in the following way.
    Less than 2,700 hours
    Displayed as a green bar.
    2,700 hours to less than 3,000 hours
    Displayed as a green and yellow bar.When the lamp hours are 2,700 hours to 
    less than 3,000 hours, the message 
    “Obtain a new lamp.” appears when 
    power is turned on.
    Over 3,000 hours
    Displayed as a green, yellow and red 
    bar.
    The message “Replace with the new 
    lamp.” appears when power is turned on. 
    						
    							137
    Setting Various Functions
    User’s ManualSettin
    g Functions from Menus
    Filter Warning Display
    [Filter warning display]
    A message advising you to perform clean-
    ing can be set to display when the filter 
    needs cleaning.
    MENU > [Install settings] > [On screen] > [Filter 
    warning display]
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     The factory default is [On].
    Resetting the Air Filter 
    Counter
    [Filter counter]
    This resets the counter which reminds you 
    of the time for cleaning and replacing the 
    air filter.
    MENU > [System settings] > [Other settings] > 
    [Filter counter]
    If the OK button is pressed on [Filter 
    counter], the air filter counter is displayed.
    Select [Reset] and press the OK button.
    [OK] is selected on the confirmation 
    screen and the OK button is pressed, the 
    air filter counter is reset.
    Press the MENU button or EXIT button 
    (WX6000 / SX6000).
    HDMIComponent
    Digital PCAnalog PC
    OffThe filter warning display is not 
    displayed.
    OnThe filter warning display is dis-
    played.HDMIComponent
    Digital PCAnalog PC
    For details about how to replace or 
    clean the filter, refer to page 193. 
    						
    							Setting Various Functions
    138
    Displaying Test Pattern
    [Test pattern]
    A test pattern for checking the resolution 
    and color when installing the projector can 
    be displayed.
    MENU > [Install settings] > [Test pattern]
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     The factory default is [Off].
     While the test pattern is displayed, you can 
    use the 
    [] / [] buttons to change to a dif-
    ferent test pattern. Also, if a test pattern has 
    option settings, you can change the settings 
    using the 
    [] / [] button. (P217)
     The test pattern can also be displayed or 
    turned off by pressing the TEST PATTERN 
    button on the remote control.
    HDMIComponent
    Digital PCAnalog PC
    OffThe test pattern is not displayed.
    OnThe test pattern is displayed.
    The following functions in the [Image 
    adjustment] tab are not applied to the 
    test pattern.
     Brightness adjustment function 
    (P111)
     Contrast adjustment function (P112)
     Sharpness adjustment function 
    (P113)
     Color level adjustment function 
    (P114)
     Color balance adjustment function 
    (P114) 
    						
    							139
    Setting Various Functions
    User’s ManualSettin
    g Functions from Menus
    Selecting Audio In Termi-
    nal
    [Audio in terminal select]
    You can select the audio in terminal that is 
    used for each input signal (HDMI, Digital 
    PC, Analog PC-1, Analog PC-2, Compo-
    nent).
    MENU > [Install settings] > [Audio in terminal 
    select]
    Press the OK button to accept your setting 
    and then press the  MENU button or EXIT 
    button (WX6000 / SX6000).
    • The factory default is as follows.
    HDMI: HDMI
    Digital PC: Audio in 2
    Analog PC-1: Audio in 1
    Analog PC-2: Audio in 2
    Component: Audio in 1
    Locking Installation 
    Related Functions
    [Positional lock]
    Operation of installation related functions 
    can be prohibited.
    MENU > [Install settings] > [Positional lock]
    Press the  OK button to accept your setting 
    and then press the  MENU button or  EXIT 
    button (WX6000 / SX6000).
     The factory default is [Off].
     The positional lock can be applied to Test 
    pattern display, Screen aspect settings, Key-
    stone adjustment, Digital image shift adjust-
    ment, Image flip H/V, Focus adjustment, 
    Zoom adjustment, Lens shift adjustment and 
    Lens shift reset.
    HDMIComponent
    Digital PCAnalog PC
    Off No audio is output.
    Audio in 1 Outputs the audio signal that 
    is inputted in Audio in terminal 
     1.
    Audio in 2 Outputs the audio signal that 
    is inputted in Audio in terminal 
     2.
    HDMI Outputs the HDMI audio sig-
    nal. (Only for HDMI)
    HDMIComponent
    Digital PCAnalog PC
    Off The positional lock is not used.
    On Installation related functions can-
    not be used. 
    						
    							Setting Various Functions
    140
    Resetting to the Default Setting
    [Factory defaults]
    You can reset the menu item settings and 
    restore the system settings to the factory 
    defaults.
    MENU > [System settings] > [Other settings] > 
    [Factory defaults]
    MENU > [System settings] > [Other settings] > 
    [Factory defaults]
    Select [Factory defaults] and press the OK 
    button. The following screen for confirma-
    tion appears.
     This function does not reset the values for 
    [Lamp counter], [Language], [Remote con-
    trol], [Input signal], [Network Setting], [Filter 
    counter], [Focus position], [Zoom position], 
    and [Lens shift position].
     For factory defaults settings, refer to pages 
    232 – 238.
     The contents of the user memory return to the 
    conditions at the time it was saved. (P110)
    HDMIComponent
    Digital PCAnalog PC
    OKSettings are reset to default.
    CancelSettings are not reset to default. 
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon Projector WUX5000 User Manual