Home > Canon > Projector > Canon Projector WUX5000 User Manual

Canon Projector WUX5000 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Canon Projector WUX5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							41
    Part Names
    Before Use
    (1)LAN port (P166)
    Connects the LAN cable.
    Used to connect the projector to a network.
    (2)ANALOG PC-1 / COMPONENT IN terminal
    ( /COMPONENT IN) (P47, P53)
    Receives the analog PC signal (Analog PC-1).
    A component cable can be used to receive the component image signal (Component).
    (3)ANALOG PC- 2 / DVI-I IN terminal (  DVI-I IN) (P50)
    Connects the external monitor output from a computer.
    Receives the digital PC signal (Digital PC) or analog PC signal (Analog PC-2).
    (4)HDMI IN terminal (HDMI IN) (P51)
    Receives the digital content image signal (HDMI).
    Carries both video and audio signals across a single cable.
    (5)Service port (CONTROL)
    This terminal is used by servicing technicians. It is not used during ordinary use.
    (6)Terminal for wired remote control (REMOTE) (P30)
    This terminal is used to connect the remote control using a cable.
    (7)AUDIO IN terminal (AUDIO IN) (P47, P50, P53)
    Receives the audio signal input for 2 kinds of image input except HDMI IN.
    The internal speaker outputs the audio for the selected image signal.
    (8)AUDIO OUT terminal ( AUDIO OUT) (P51, P55)
    Outputs the audio to external AV equipment. This outputs the audio signal that corre-
    sponds to the projected image signal.
    (1) (2)
    (3) (4) (5) (6) (7) (8) 
    						
    							43
    MULTIMEDIA PROJECTOR
    User’s Manual
    (Operation) 
    						
    							Safety Instructions
    Before Use Table of Contents
    Projecting an Image
    Useful Functions Available 
    During a Presentation
    Setting Functions from Menus
    User’s Manual
    Installation
    Connecting to a Network
    Maintenance
    Appendix
    Index
    Appendix Installation Manual
    45
    Projecting an 
    Image 
    						
    							46
    Steps for Connecting the Projector and Projecting an Image
    Connecting the Projector to Equipment (P162)
    Starting Projection (P56)
    Selecting an Input Signal (P59)
    Adjusting the Image (P61)
    Make the following adjustments.
     Setting the Display Resolution of the Computer 
    (P61)
     Selecting an Aspect Ratio of Projected Image (Screen aspect) and a Screen 
    Mode (Aspect) 
    (P63, P69)
    Adjusting Misaligned Images or Flickering of the Screen Using the Auto PC (P62)
     Adjusting the Image Size (P71)
     Adjusting the Focus (P73)
     Adjusting the Image Position (Lens shift) (P74)
     Adjusting Keystone Distortion 
    (P76)
    Making Fine Adjustments
     Selecting an Image Mode 
    (P78)
    Do you want to project an image from a 
    notebook computer?
    Is the image projected properly?
    No
    For a notebook computer, 
    turn on the monitor output 
    (P58) and then proceed.
    NoYes
    Projection is complete.Yes
    Installation work should be performed by a qualified technician. 
    Contact the Canon Customer Support Center for further information. 
    						
    							47
    User’s ManualProjectin
    g an Ima
    ge
    Connecting the Projector
    Connecting the Projector to a Computer
    Connect the projector to the computer.
    A digital connection (P50) is recommended when projecting an image in high quality.
    When using a computer with an HDMI output terminal, a digital connection (P51) can be 
    made using an HDMI cable.
    ■Connecting to RGB Monitor Output Terminal (Analog Connection)
    Connecting with a VGA cable (Input signal type: [Analog PC] (WUX5000 / WUX4000), 
    [Analog PC-1] (WX6000 / SX6000) P59) Before connecting the cables, turn off both the projector and computer.
    Computer
    Monitor output 
    terminal
    (mini D-sub 15-pin)
    AUDIO output terminal 
    (AUDIO OUT)
    VGA cable (supplied)
    When inputting corresponding audio
    Audio cable (not included)To ANALOG PC / 
    COMPONENT IN terminal
    To AUDIO IN terminalProjector 
    						
    							Connecting the Projector
    48
    Connecting with VGA-DVI cable (Input signal type: [Analog PC-2] P59)
     Use a VGA cable in which all pins are connected. If the cable is a type in which all pins 
    are not connected, the image may not be correctly displayed.
     Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
    will reduce the audio volume.
     The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139). 
    (WX6000 / SX6000)
    Computer
    Monitor output 
    terminal
    (mini D-sub 15-pin)
    AUDIO output terminal 
    (AUDIO OUT)
    VGA cable (supplied)
    When inputting corresponding audio
    Audio cable (not included)To ANALOG PC-1 / 
    COMPONENT IN terminal
    To AUDIO IN terminalProjector
    Computer
    Monitor output 
    terminal
    (mini D-sub 15-pin)
    AUDIO output terminal 
    (AUDIO OUT)
    VGA-DVI-I cable (not included)
    When inputting corresponding audio
    Audio cable (not included)To ANALOG PC-2 / 
    DVI-I IN terminal
    To AUDIO IN terminalProjector 
    						
    							49
    Connecting the Projector
    User’s ManualProjectin
    g an Ima
    ge
    Connecting with a BNC cable (Input signal type: [Analog PC] (WUX5000 / WUX4000), 
    [Analog PC-1] (WX6000 / SX6000) P59)
     A signal with a dot clock higher than 162 MHz cannot be projected.
     Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
    will reduce the audio volume.
     The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139). 
    (WX6000 / SX6000)
    Computer
    Monitor output 
    terminal
    (mini D-sub 15-pin)
    AUDIO output terminal 
    (AUDIO OUT)
    BNC cable (not included)
    When inputting corresponding audio
    Audio cable (not included)To ANALOG PC / 
    COMPONENT IN terminal
    To AUDIO IN terminal
    Projector
    Mini D-sub 15-pin - 
    BNC terminal con-
    verter cable (not 
    included)Mini D-sub 15-pin - 
    BNC terminal con-
    verter cable (not 
    included)
    Computer
    Monitor output 
    terminal
    (mini D-sub 15-pin)
    AUDIO output terminal (AUDIO OUT)
    BNC cable (not included)
    When inputting corresponding audio
    Audio cable (not included)To ANALOG PC-1 / 
    COMPONENT IN terminal
    To AUDIO IN terminal
    Projector
    Mini D-sub 15-pin - 
    BNC terminal con-
    verter cable (not 
    included)Mini D-sub 15-pin - 
    BNC terminal con-
    verter cable (not 
    included) 
    						
    							Connecting the Projector
    50
    ■Connecting to DVI Monitor Output Terminal (Digital Connection)
    Connecting with a DVI cable (Input signal type: [DVI-D] (Digital PC) – P59)
     Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
    will reduce the audio volume.
     The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139). 
    (WX6000 / SX6000)
    Computer
    Monitor output 
    terminal
    (DVI terminal)
    AUDIO output terminal 
    (AUDIO OUT)
    DVI-D cable (not included)
    When inputting corresponding sound
    Audio cable (not included)To DVI-D IN terminal
    To AUDIO IN terminal
    Projector
    Computer
    Monitor output 
    terminal
    (DVI terminal)
    AUDIO output terminal 
    (AUDIO OUT)
    DVI-I cable (not included)
    When inputting corresponding audio
    Audio cable (not included)To Analog PC-2 / DVI-I IN 
    terminal
    To AUDIO IN terminal
    Projector 
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon Projector WUX5000 User Manual