Home > Canon > Projector > Canon Projector WUX5000 User Manual

Canon Projector WUX5000 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Canon Projector WUX5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							171
    Installation Manual Connecting to a Networ
    k
    Network Settings on the Projector
    From the projector menus screen, network 
    settings can be configured in the [Network 
    Setting] tab. For the menu operations, 
    refer to page 88.
    (The screen is for the WUX5000 / 
    WUX4000.)Locking the Network Settings
    You can lock / unlock the network settings 
    so that they cannot be changed and cancel 
    the lock.
    MENU > [Network Setting] > [Network Setting 
    lock]
    After the OK button is pressed to accept 
    your setting and the MENU button or the 
    EXIT button (WUX6000 / SX6000) is 
    pressed to close the window, the lock is 
    re-engaged. If you change the network 
    settings, be sure to continue operating 
    without closing the window.
     [Lock] is the factory default.
     For the default network password, refer to 
    page 173.
    UnlockCancels the lock and allows 
    other network settings to be 
    changed. The password must 
    be entered in order to cancel the 
    lock.
    When [Unlock] is selected, the 
    window shown below appears. 
    Use the [] / [] / [] / [] but-
    tons to enter the 4-digit pass-
    word.
    For the WX6000 / SX6000, num-
    bers can be entered using the 
    numerical buttons on the remote 
    control.
    LockLock the settings. 
    						
    							Network Settings on the Projector
    172
    Turning the Network Function 
    On / Off
    You can turn the projector network function 
    on or off. Power can be saved by turning 
    the function [Off].
    MENU > [Network Setting] > [Network function]
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     [Off] is the factory default.
    Forcibly canceling the network lockIn the Network Password Input screen, press the 
    buttons in the following sequence to cancel the 
    lock: [ ] [OK] [ ] [OK] [ ] [OK]. This will reset 
    the network password to [ ] [ ] [ ] [ ].
    OffDisables the network function.
    OnEnables the network function. 
    						
    							173
    Network Settings on the Projector
    Installation Manual Connecting to a Networ
    k
    Setting a Network Password
    You can set whether or not a password is 
    required in order to change the projector 
    network settings.
    MENU > [Network Setting] > [Network Pass-
    word setting]
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     [On] is the factory default.
    Registering a Network Pass-
    word
    Register the projector network password.
    MENU > [Network Setting] > [Register Network 
    Password]
    When [Register Network Password] is 
    selected, the window shown below 
    appears. 
    Enter a 4 digit password.
    For the WUX5000 / WUX4000, the pass-
    word can be entered using the [ ] / [ ] / 
    [ ] / [ ] buttons. For the WX6000 / 
    SX6000, the password can be entered 
    using a combination of the numerical but-
    tons and the [ ] / [ ] / [ ] / [ ] buttons. 
    [ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4] 
    have the same function.
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     The factory default is [ ] [ ] [ ] [ ] 
    (WUX5000 / WUX4000) or [1] [1] [1] [1] 
    (WX6000 / SX6000).
    OffA network password is not used.
    OnA network password is used. 
    						
    							Network Settings on the Projector
    174
    Turning the PJLink Function 
    On / Off
    You can turn the PJLink network function 
    on or off. When the function is turned on, 
    control is possible via the LAN using com-
    mands that meet PJLink standards.
    MENU > [Network Setting] > [PJLink]
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     [On] is the factory default.
     This projector conforms to Class 1 as 
    defined in the PJLink standards of the 
    JBMIA (Japan Business Machine and 
    Information System Industries Associa-
    tion). This projector supports all com-
    mands that are defined by PJLink Class 1, 
    and has been verified as conforming to the 
    PJLink standard Class 1 definition.
     For information about using PJLink, refer to 
    page 187.
    OffDisables the PJLink function.
    OnEnables the PJLink function.
    What is PJLink?
    In September 2003, the PJLink Work-
    ing Group was established under the 
    Data Projector Committee. During the 
    first year, this PJLink Working Group 
    standardized PJLink as a new inter-
    face specification for projectors.
    PJLink is a unified standard for opera-
    tion and control of projectors.
    It allows centralized control of projec-
    tors and operation from a controller for 
    all projectors regardless of manufac-
    turer.
    The objective is for JBMIA to improve 
    convenience for users and expand 
    the use of projectors through early 
    systemization for network monitoring 
    and control of projectors, which will 
    become the mainstream in the future.
    Class 1: Standardization of control 
    and monitoring specifications for 
    basic projector functions
    Basic projector control: Power control, 
    input selection, etc.
    Acquisition of projector information 
    and status: Power status, input selec-
    tion status, error status, lamp use 
    time, etc.
    JBMIA:  Japan Business Machine and 
    Information System Industries 
    Association
    The Japan Business Machine 
    and Information System 
    Industries Association is an 
    organization which was 
    launched in 1960 and 
    changed its name on April 1, 
    2002.
    PJLink is a registered trademark of JBMIA and 
    pending trademark in some countries. 
    						
    							175
    Network Settings on the Projector
    Installation Manual Connecting to a Networ
    k
    Turning DHCP Function On / 
    Off
    You can turn the projector DHCP function 
    on or off. 
    MENU > [Network Setting] > [DHCP]
    Press the OK button to accept your setting 
    and then press the MENU button or EXIT 
    button (WX6000 / SX6000).
     [Off] is the factory default.
    TCP / IP Setting
    Configure the projector TCP / IP settings.
    MENU > [Network Setting] > [TCP/IP setting]
    When [TCP/IP setting] is selected, the win-
    dow shown below appears. Use the 
    [] / 
    [ ] buttons to select the IP address, then 
    press the OK button. Next, use the [ ] / 
    [ ] buttons to select the digit and the 
    [] / 
    [ ] buttons to change the value. For the 
    WX6000 / SX6000, numbers can be 
    entered using the numerical buttons on 
    the remote control. Press the OK button, 
    then set the subnet mask and gateway 
    address in the same way. Finally, select 
    [Enter].
     The factory defaults are shown below.
    IP address 192.168.254.254
    Subnet mask 255.255.255.0
    Gateway address 0.0.0.0
     Settings cannot be made when [DHCP] 
    (P175) is [On].
     If an invalid value is entered, the message 
    “Invalid entry” appears. If this occurs, 
    enter a valid value.
    OffDisables the DHCP function. TCP / IP 
    settings are possible.
    OnEnables the DHCP function. 
    Searches the DHCP server
    . Because 
    the IP address is acquired from the 
    DHCP server, it is not necessary to 
    enter the TCP / IP settings (IP 
    address, subnet mask, gateway 
    address). 
    						
    							Network Settings on the Projector
    176
    Initializing Network Settings
    You can initialize the projector network set-
    tings.
    MENU > [Network Setting] > [Network setting 
    initialization]
    When [Network setting initialization] is 
    selected, the window shown below 
    appears. Select [YES] then press the OK 
    button.
     The following items are initialized.
    Network setting screen user name, various 
    settings including password
    Network Password setting
    Register Network Password
    PJLink
    DHCP
    IP address
    Subnet mask
    Gateway address
    E-mail sender address
    E-mail recipient address
    Projector name
    Location 
    						
    							177
    Installation Manual Connecting to a Networ
    k
    Configuring the Network From the Computer
    ■Displaying and Configuring the Network Configuration Screen
    The web browser screen shown below is for the WUX4000.
    1Turn on the computer and projector.
    2Launch a web browser, enter “http://(projector IP address)” in the address bar, and 
    press the Enter key.
    The password input screen appears.
    3Enter the user name and password on the password input screen, then click OK.
    The factory default user name is “root” and the password is “system”.
    The projector web screen appears in the web browser.
    The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the net-
    work administrator for the projector IP address. It is possible to check the IP address from 
    the projector menu. 
    						
    							Configuring the Network From the Computer
    178
    The following information is displayed.
    *1 WUX5000 / WX6000 / SX6000
    *2 WUX4000
    4To configure, click [Settings]. 
    The settings window appears.
    Projector name The name of the projector on the network
    Location The location of projector installation
    MAC address The MAC address of the projector
    IP address The IP address of the projector
    Power Status The power status of the projector
    Lamp Time *1 Lamp operating time
    Lamp Time Normal Mode *2 Lamp operating time in [Normal] lamp mode
    Lamp Time Quiet Mode *2 Lamp operating time in [Quiet] lamp mode
    Lamp Time Converted *2 Lamp operating time (converted value)
    Filter Time Air filter operating time
    Alert Error message (if an error has occurred)
    Temperature abnormality
    Faulty lamp
    Faulty lamp cover
    Faulty cooling fan
    Faulty power supply
    Faulty lens connector: Lens connector error
    Faulty air filter unit: Air filter error
    Unknown error
    To operate the projector from the computer, click [Projector control] (
    P188). 
    						
    							179
    Configuring the Network From the Computer
    Installation Manual Connecting to a Networ
    k
    5Select the function to set from the menu (1), then enter the setting in the displayed 
    field (2) and click [OK] (3).
    6A confirmation window appears. Check the contents and if they are correct, click 
    [Apply].
    The settings are applied to the projector and “Save completed” is displayed.
    7Click [Back to top] to return the web screen to the initial page.
    (2) (1)
    (3) 
    						
    							Configuring the Network From the Computer
    180
    ■Resetting to Factory Defaults
    1Perform steps 1 - 3 on page 177 to display the setting window.
    2Click [Initialize].
    3A confirmation window appears. Click [OK]. 
    ■Setting Errors
    When a setting-related error occurs, the error name is displayed on the screen, and a 
    “!” mark is displayed next to the input field which caused the error. 
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon Projector WUX5000 User Manual