Canon Projector WUX450 User Manual
Here you can view all the pages of manual Canon Projector WUX450 User Manual. The Canon manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 81
81 Operation Useful Functions Available During a Presentation Split-Screen Display Two input images can be projected side by side. This is split-screen display. When you activate split-screen display, the current image is shown on the left side, and the new image is shown at right. You can change the source of images shown on each side by pressing the INPUT button. However, you cannot specify the same input signal (terminal) as the source for both sides. 1Supply two signals to the projector. 2Press...
Page 82
![Page 82
82
Split-Screen Display
3If or is displayed in the center of the image area, you can switch control
to the other side by pressing the [ ] / [ ] buttons on the remote control.
(Example of display in split-screen mode.)
4Press the INPUT button to select the input signal for the side with control
rights.
The [Input] menu is displayed. To determine which side is currently under
control, check the screen ID in orange in the upper right of the menu. The side
without control rights is labeled with a...](http://img.usermanuals.tech/thumb/14/99365/w300_projector_manual_7685_d-81.png "Page 82
82
Split-Screen Display
3If or is displayed in the center of the image area, you can switch control
to the other side by pressing the [ ] / [ ] buttons on the remote control.
(Example of display in split-screen mode.)
4Press the INPUT button to select the input signal for the side with control
rights.
The [Input] menu is displayed. To determine which side is currently under
control, check the screen ID in orange in the upper right of the menu. The side
without control rights is labeled with a...")
82 Split-Screen Display 3If or is displayed in the center of the image area, you can switch control to the other side by pressing the [ ] / [ ] buttons on the remote control. (Example of display in split-screen mode.) 4Press the INPUT button to select the input signal for the side with control rights. The [Input] menu is displayed. To determine which side is currently under control, check the screen ID in orange in the upper right of the menu. The side without control rights is labeled with a...
Page 83
83 Table of Contents Safety Instructions Before Use Operation Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation and Maintenance Installation Connecting to a Network Maintenance Networked Multi-Projection Networked Multi-Projection Overview Operation in Each Mode Functions in All Modes AppendixOther Information Index Setting Functions from Menus
Page 84
![Page 84
84
Using Menus
Use the menus to set the operation of the projector in detail.
Menu Configuration
The menu screen is divided into 6 tabs as shown below.
Menu items
[System settings] tab
You can set the operation of the
projector.
[Network settings] tab
These settings are for when using
the projector from a PC via a
network.
For the network settings, refer to
“Connecting to a Network” (P167).
[Information] tab
You can check information
about the signal types of the
images projected and other...](http://img.usermanuals.tech/thumb/14/99365/w300_projector_manual_7685_d-83.png "Page 84
84
Using Menus
Use the menus to set the operation of the projector in detail.
Menu Configuration
The menu screen is divided into 6 tabs as shown below.
Menu items
[System settings] tab
You can set the operation of the
projector.
[Network settings] tab
These settings are for when using
the projector from a PC via a
network.
For the network settings, refer to
“Connecting to a Network” (P167).
[Information] tab
You can check information
about the signal types of the
images projected and other...")
84 Using Menus Use the menus to set the operation of the projector in detail. Menu Configuration The menu screen is divided into 6 tabs as shown below. Menu items [System settings] tab You can set the operation of the projector. [Network settings] tab These settings are for when using the projector from a PC via a network. For the network settings, refer to “Connecting to a Network” (P167). [Information] tab You can check information about the signal types of the images projected and other...
Page 85
![Page 85
Using Menus
85
Operation
Setting Functions from Menus
Basic Menu Operations
1Press the MENU button to display the menu window.
2Press the [ ] / [ ] buttons to select a tab.
•If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to
move the current selection to the top.
3Press the [ ] / [ ] buttons to select an item.
4Select contents.
How to select the contents varies depending on the item.
Selecting from a list Example: Aspect (P87)
Remote controlProjector
Remote...](http://img.usermanuals.tech/thumb/14/99365/w300_projector_manual_7685_d-84.png "Page 85
Using Menus
85
Operation
Setting Functions from Menus
Basic Menu Operations
1Press the MENU button to display the menu window.
2Press the [ ] / [ ] buttons to select a tab.
•If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to
move the current selection to the top.
3Press the [ ] / [ ] buttons to select an item.
4Select contents.
How to select the contents varies depending on the item.
Selecting from a list Example: Aspect (P87)
Remote controlProjector
Remote...")
Using Menus 85 Operation Setting Functions from Menus Basic Menu Operations 1Press the MENU button to display the menu window. 2Press the [ ] / [ ] buttons to select a tab. •If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to move the current selection to the top. 3Press the [ ] / [ ] buttons to select an item. 4Select contents. How to select the contents varies depending on the item. Selecting from a list Example: Aspect (P87) Remote controlProjector Remote...
Page 86
![Page 86
86
Using Menus
Adjusting with the [ ] / [ ] buttons Example: Contrast (P99)
Selecting from a different screen (1) Example: Menu position (P154)
Selecting from a different screen (2) Example: Tracking (P89)
5Pressing the MENU button causes the menu screen to disappear.
The menu screen will also disappear if the EXIT button is pressed.
1. Select [Contrast].
2. Use the [ ] / [ ] buttons to adjust
the setting.
1. Select [Menu position].
2. Press the OK button to display a
different screen.
3. Then...](http://img.usermanuals.tech/thumb/14/99365/w300_projector_manual_7685_d-85.png "Page 86
86
Using Menus
Adjusting with the [ ] / [ ] buttons Example: Contrast (P99)
Selecting from a different screen (1) Example: Menu position (P154)
Selecting from a different screen (2) Example: Tracking (P89)
5Pressing the MENU button causes the menu screen to disappear.
The menu screen will also disappear if the EXIT button is pressed.
1. Select [Contrast].
2. Use the [ ] / [ ] buttons to adjust
the setting.
1. Select [Menu position].
2. Press the OK button to display a
different screen.
3. Then...")
86 Using Menus Adjusting with the [ ] / [ ] buttons Example: Contrast (P99) Selecting from a different screen (1) Example: Menu position (P154) Selecting from a different screen (2) Example: Tracking (P89) 5Pressing the MENU button causes the menu screen to disappear. The menu screen will also disappear if the EXIT button is pressed. 1. Select [Contrast]. 2. Use the [ ] / [ ] buttons to adjust the setting. 1. Select [Menu position]. 2. Press the OK button to display a different screen. 3. Then...
Page 87
![Page 87
87
Operation
Setting Functions from Menus
Setting Display Status (Input Settings)
Selecting the Aspect
> [Input settings] > [Aspect]
You can select a projection mode
corresponding to the aspect ratio of
the image. (P66)
• For LAN and USB input, [Auto] is selected
automatically.
• Different contents are displayed for different
screen aspects or input signal types.
• The ASPECT button on the remote control
can also be used to select the [Aspect]
settings.
Press the OK button to accept your
setting...](http://img.usermanuals.tech/thumb/14/99365/w300_projector_manual_7685_d-86.png "Page 87
87
Operation
Setting Functions from Menus
Setting Display Status (Input Settings)
Selecting the Aspect
> [Input settings] > [Aspect]
You can select a projection mode
corresponding to the aspect ratio of
the image. (P66)
• For LAN and USB input, [Auto] is selected
automatically.
• Different contents are displayed for different
screen aspects or input signal types.
• The ASPECT button on the remote control
can also be used to select the [Aspect]
settings.
Press the OK button to accept your
setting...")
87 Operation Setting Functions from Menus Setting Display Status (Input Settings) Selecting the Aspect > [Input settings] > [Aspect] You can select a projection mode corresponding to the aspect ratio of the image. (P66) • For LAN and USB input, [Auto] is selected automatically. • Different contents are displayed for different screen aspects or input signal types. • The ASPECT button on the remote control can also be used to select the [Aspect] settings. Press the OK button to accept your setting...
Page 88
![Page 88
88
Setting Display Status (Input Settings)
Setup Using Auto PC
> [Input settings] > [Auto PC]
Automatically adjusts display
position misalignment and screen
flickering. The adjusted result is
stored in the memory.
Press the OK button to accept your
setting.
Selecting an Input
Signal
> [Input settings] > [Input signal
select]
You can select a suitable resolution
if the auto PC adjustment function
(P57) cannot project the correct
image from a computer.
Press the OK button to accept your...](http://img.usermanuals.tech/thumb/14/99365/w300_projector_manual_7685_d-87.png "Page 88
88
Setting Display Status (Input Settings)
Setup Using Auto PC
> [Input settings] > [Auto PC]
Automatically adjusts display
position misalignment and screen
flickering. The adjusted result is
stored in the memory.
Press the OK button to accept your
setting.
Selecting an Input
Signal
> [Input settings] > [Input signal
select]
You can select a suitable resolution
if the auto PC adjustment function
(P57) cannot project the correct
image from a computer.
Press the OK button to accept your...")
88 Setting Display Status (Input Settings) Setup Using Auto PC > [Input settings] > [Auto PC] Automatically adjusts display position misalignment and screen flickering. The adjusted result is stored in the memory. Press the OK button to accept your setting. Selecting an Input Signal > [Input settings] > [Input signal select] You can select a suitable resolution if the auto PC adjustment function (P57) cannot project the correct image from a computer. Press the OK button to accept your...
Page 89
![Page 89
89
Setting Display Status (Input Settings)
Operation
Setting Functions from Menus
Adjusting the Input
Signal
(Total dots)
> [Input settings] > [Input signal
settings] >
[Total dots]
You can adjust the total number of
dots in the horizontal direction.
Adjust it when stripes are displayed
on the screen.
Use the [ ] / [ ] buttons to select a
value.
When you have completed the
adjustment, press the OK button to
accept your setting and then press the
MENU button or EXIT button.
• Perform this...](http://img.usermanuals.tech/thumb/14/99365/w300_projector_manual_7685_d-88.png "Page 89
89
Setting Display Status (Input Settings)
Operation
Setting Functions from Menus
Adjusting the Input
Signal
(Total dots)
> [Input settings] > [Input signal
settings] >
[Total dots]
You can adjust the total number of
dots in the horizontal direction.
Adjust it when stripes are displayed
on the screen.
Use the [ ] / [ ] buttons to select a
value.
When you have completed the
adjustment, press the OK button to
accept your setting and then press the
MENU button or EXIT button.
• Perform this...")
89 Setting Display Status (Input Settings) Operation Setting Functions from Menus Adjusting the Input Signal (Total dots) > [Input settings] > [Input signal settings] > [Total dots] You can adjust the total number of dots in the horizontal direction. Adjust it when stripes are displayed on the screen. Use the [ ] / [ ] buttons to select a value. When you have completed the adjustment, press the OK button to accept your setting and then press the MENU button or EXIT button. • Perform this...
Page 90
![Page 90
90
Setting Display Status (Input Settings)
Adjusting the Input
Signal
(Horizontal position)
> [Input settings] > [Input signal
settings] >
[Horizontal position]
You can adjust the horizontal
position of the screen when the
projected image is shifted in the
horizontal direction.
Use the [ ] / [ ] buttons to select a
value. As the value increases, the
screen moves to the left.
When you have completed the
adjustment, press the OK button to
accept your setting and then press the
MENU button or...](http://img.usermanuals.tech/thumb/14/99365/w300_projector_manual_7685_d-89.png "Page 90
90
Setting Display Status (Input Settings)
Adjusting the Input
Signal
(Horizontal position)
> [Input settings] > [Input signal
settings] >
[Horizontal position]
You can adjust the horizontal
position of the screen when the
projected image is shifted in the
horizontal direction.
Use the [ ] / [ ] buttons to select a
value. As the value increases, the
screen moves to the left.
When you have completed the
adjustment, press the OK button to
accept your setting and then press the
MENU button or...")
90 Setting Display Status (Input Settings) Adjusting the Input Signal (Horizontal position) > [Input settings] > [Input signal settings] > [Horizontal position] You can adjust the horizontal position of the screen when the projected image is shifted in the horizontal direction. Use the [ ] / [ ] buttons to select a value. As the value increases, the screen moves to the left. When you have completed the adjustment, press the OK button to accept your setting and then press the MENU button or...