Canon Projector WUX450 User Manual

Installation Procedure
131
Installation and Maintenance
Installation
■Projection from High Surfaces
For projection from a shelf or other high surface, the projector can be installed 
upside-down and the projected image inverted. In this case, attach the option feet 
on top of the projector.
Attaching Option Feet (RS-FT01, Sold Separately)
Remove the hole caps and screw the option feet into the holes.
The caps are located at four positions on top of the projector. They are removed 
differently depending...

Installation Procedure
132
Removing hole caps labeled (2) 
Open the lamp cover and use a screwdriver or similar tool to 
push off the caps from below.
■Ceiling Mounting or Rear Projection
You can mount the projector on the ceiling (ceiling mounting) with it turned upside 
down or place it behind the screen (rear projection) if you use a translucent screen.
Make sure to use the optional ceiling attachment. For the ceiling attachment, refer 
to “Option” (P305). For details, refer to the assembly and...

Installation Procedure
133
Installation and Maintenance
Installation
Relationship of Image Size to Projection 
Distance
The size of projected images is determined by zooming, relative to the distance 
from the projector to the screen. (Optical zooming on the WUX450/WX520, and 
electronic zooming on the WUX400ST/WX450ST.) Refer to the following table and 
decide the distance between the projector and screen.
WUX450/WX520Projection distance  [m (feet)]
WUX400ST/WX450STProjection distance  [m (feet)]
Image...

Installation Procedure
134
■Lens Shift Function
You can reposition the image in all directions by turning the lens shift dials on the 
side of the projector, which moves the lens up, down, left, or right. For instructions, 
refer to “Lens Shift Control” (P45).
■Amount of Lens Shift
The amount of lens shift is indicated as a percentage relative to the image height 
and width.
The lens shift ranges for each model of projector are as follows.
The projector supports vertical and horizontal lens shift....

Installation Procedure
135
Installation and Maintenance
Installation
Maximum upward (A) and horizontal (B) movement using lens shift
(reference values, in cm)
WUX450/WX520
WUX400ST/WX450ST
Image 
Size 
(Dia.)WUX450 WX520
16:10 16:9 4:3 16:10 16:9 4:3
ABABABABABAB
40 32 (12.6)9 (3.5)30 (11.8)9 (3.5)37 (14.6)8 (3.1)33 (13.0)9 (3.5)31 (12.2)9 (3.5)38 (15.0)8 (3.1)
60 48 (18.9)13 (5.1)45 (17.7)13 (5.1)55 (21.7)12 (4.7)48 (18.9)13 (5.1)45 (17.7)13 (5.1)55 (21.7)12 (4.7)
80 65 (25.6)17 (6.7)60 (23.6)18 (7.1)73...

136
Connection Procedure
Connectable Equipment and Input Terminals
HDMIUse this name to select the image 
input.Direction of signal and data flow
HDMI 
Te r m i n a lThe name of the terminal to which 
to connect equipment(Pxxx) indicates the page(s) to refer to.
Computer (P137) AV equipment (P140)
Digital video camera* (P140) Computer (P137, P138)
AV equipment (P141)
Network (P168)
(P137, P138) Amplified 
speakers
(P139, P142)Computer (P139)
* Select playback 
mode before 
connecting.
Optional remote...

Connection Procedure
137
Installation and Maintenance
Installation
Connecting a Computer
Connect the projector to the computer.
A digital connection (P138) is recommended when projecting an image in high 
quality.
When using a computer with an HDMI output terminal, a digital connection (P139) 
can be made using an HDMI cable.
■Connecting to RGB Monitor Output Terminal (Analog 
Connection)
Connecting with a computer cable (Input signal type: [Analog PC-2] P53)
Connecting with VGA-DVI cable (Input signal...

Connection Procedure
138
Connecting with a BNC cable (Input signal type: [Analog PC-2] P53)
■Connecting to DVI Monitor Output Terminal (Digital 
Connection)
Connecting with a DVI cable (Input signal type: [Digital PC] P53)
• Use a VGA-DVI-I cable in which all pins are connected. If the cable is a type in which all 
pins are not connected, the image may not be correctly displayed.
• Use an audio cable without a built-in resistor. Using an audio cable with a built-in 
resistor will reduce the audio...

Connection Procedure
139
Installation and Maintenance
Installation
■Connecting with an HDMI cable (Input signal type: [HDMI] P53)
■Outputting Audio to Speakers
It is possible to output audio from the projected images to amplified speakers.
• Use an audio cable without a built-in resistor. Using an audio cable with a built-in 
resistor will reduce the audio volume.
• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P153).
• Use an audio cable without a built-in resistor. Using...

Connection Procedure
140
Connecting AV Equipment
Connect the projector and AV equipment.
The description provided here is one example. For more detailed information, refer 
to the manual for the connected AV equipment.
■Connecting to Digital Video Output Terminal (Digital 
Connection)
Connecting with an HDMI cable (Input signal type: [HDMI] P53)
Before connecting the cables, turn off both the projector and AV equipment.
Digital video camera
Digital video 
output terminal 
(HDMI Terminal)HDMI cable (not...