Canon Projector WUX450 User Manual

Installation-Related Menu Settings
161
Installation and Maintenance
Installation
5Select [Start position] and use the remote’s [ ] [ ] buttons to move the 
markers to the right edge where the images overlap.
6Select [Width], and use the remote’s [ ] [ ] buttons to move the markers 
to the overlapping area.
The area between the starting and ending markers is called the blending area. 
Brightness of this area is automatically adjusted to match the brightness of 
other image areas. After you complete...

Installation-Related Menu Settings
162
■Advanced Instructions: Black Level Adjustment
In overlapping projection, dark colors are projected with less intensity than other 
colors in the overlapping area. For this reason, overlapping image areas might be 
more noticeable when the images themselves are dark. You can make this 
overlapping area less distracting by adjusting the black level of non-overlapping 
image areas.
Here, the non-overlapping image area (from the end marker toward the center of 
the...

Installation-Related Menu Settings
163
Installation and Maintenance
Installation
Here, you can use the following settings in the edge blending menu.
2Select [Adjustment type] > [Black level].
3Select [D-area base], and use the remote’s [ ] [ ] buttons to adjust the 
values for area D.
As you watch the image, adjust the values so that the brightness and colors of 
the blending area and area D match. Adjust [D-area base] to lighten the black 
level, and adjust [Red], [Green], and [Blue] to obtain an...

Installation-Related Menu Settings
164
■Advanced Instructions: Smoother Overlapping Areas
Adjustments to areas A, B, and C may make the black level along the right edge of 
area D (that is, the edge bordering the blending area) more noticeable than that of 
surrounding areas.
To compensate, adjust each area as follows.
When there are multiple blending areas relative to the projected image (on all 
edges), you must adjust the width of areas A, B, and C.
In this example, instructions are given for...

Installation-Related Menu Settings
165
Installation and Maintenance
Installation
2Select [B-width], and use the remote’s [ ] [ ] buttons to specify the width 
of area B.
This will make the width of area D narrower.
3Adjust the width of area B to roughly match the area where the black level 
is noticeable, and then use the following edge-blending settings to adjust 
the black level of area B.
Adjust the black level of area B the same way as you adjusted it for area D.
For adjustment instructions, see...

166 

167
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from 
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Networked Multi-Projection
Networked Multi-Projection 
Overview
Operation in Each Mode
Functions in All Modes
AppendixOther Information
Index
Connecting to a 
Network 

168
Network Connection Overview
Connecting the projector to a network enables you to control the projector from a 
computer and receive notification of projector errors via email. Settings related to 
the network connection can be made from either the projector side (P169) or 
computer side. (P178)
Depending on the method of network connection, preparation on the computer side 
may be necessary. The following is an explanation of preparation on the computer 
side.
Connection Methods
Connect the projector...

169
Installation and Maintenance
Connecting to a Network
Completing Projector Settings
From the projector menus screen, 
network settings can be configured in 
the [Network Setting] tab. For 
instructions on menu operations, refer 
to “Using Menus”. (P84)Locking/Unlocking 
Network Settings
> [Network Settings] > 
[Network settings lock]
You can lock/unlock the network 
settings so that they cannot be 
changed.
Press the OK button to accept your 
setting, and then press the MENU 
button or EXIT button to...

Completing Projector Settings
170
Enabling/Disabling 
the Network Password
> [Network settings] > [Network 
password setting]
You can set whether or not a 
password is required in order to 
change the projector network 
settings.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is [On].
Forcibly canceling the 
network lock
On the Network password input 
screen, press the buttons in the 
following order to unlock the 
settings: [ ] [OK] [ ]...