Canon Projector WUX450 User Manual

Installation-Related Menu Settings
151
Installation and Maintenance
Installation
Specifying Micro 
Digital Image Shift
> [Install settings] > [Professional 
settings] > 
[Micro-digital image 
shift]
Use this setting to fine-tune digital 
image shift.
When you have completed the 
adjustment, press the OK button to 
accept your setting and then press the 
MENU button or EXIT button.
• [Off] is the factory default.
• Select [Adjust] to fine-tune the image 
position.
Adjusting Image 
Registration
> [Install...

Installation-Related Menu Settings
152
Specifying the Fan 
Mode
> [Install settings] > [Professional 
settings] > 
[Fan mode]
Enable suitable cooling by switching 
the fan mode to the setting for low- 
or high-altitude (above 2,300 m 
(7,545.8)) operation.
When the setting is completed, press 
the OK button to accept your setting 
and then press the MENU button or 
EXIT button.
• [Normal] is the factory default.
Specifying Vertical 
Projection
> [Install settings] > [Professional 
settings] > 
[Vertical...

Installation-Related Menu Settings
153
Installation and Maintenance
Installation
Selecting the Audio In 
Terminal
> [Install settings] > [Audio in 
terminal select]
You can select the audio in terminal 
that is used for each input signal 
(HDMI, Digital PC, Analog PC-1, 
Analog PC-2, Component).
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is as follows.
HDMI [HDMI]
Digital PC [Audio in 1]
Analog PC-1 [Audio in 1]
Analog PC-2 [Audio in...

Installation-Related Menu Settings
154
Specifying a Menu 
Position
> [Install settings] > [On screen] > 
[Menu position]
You can change the position of 
menus displayed.
Use the [ ] / [ ] / [ ] / [ ] buttons to 
move the menu to the desired position.
After you have moved the menu to the 
desired position, press the OK button to 
accept your setting, and then press the 
MENU or EXIT button.
Showing/Hiding the 
Guide Screen
> [Install settings] > [On screen] > 
[Guide]
You can select whether to show or...

Installation-Related Menu Settings
155
Installation and Maintenance
Installation
Showing/Hiding Input 
Status
> [Install settings] > [On screen] > 
[Show input status]
You can select whether the signal 
status is displayed on the screen 
when there is no signal or when 
making signal settings.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is [On].
Showing/Hiding 
Overheat Warnings
> [Install settings] > [On screen] >
 [Overheat warning...

Installation-Related Menu Settings
156
Specifying the Menu 
Display Time
> [Install settings] > [On screen] > 
[Menu display time]
The setting for the menu display 
time can be extended from the 
normal 10 or 30 seconds to 3 
minutes.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• [Normal] is the factory default.
• The following display and operation are also 
changed.
Showing/Hiding Lamp 
Replacement 
Warnings
> [Install settings] > [On screen] >
[Lamp...

Installation-Related Menu Settings
157
Installation and Maintenance
Installation
Showing/Hiding Filter 
Cleaning Warnings
> [Install settings] > [On screen] > 
[Air filter warning display]
A message advising you to perform 
cleaning can be set to display when 
the filter needs cleaning.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is [On].
Showing/Hiding Split-
Screen ID
> [Install settings] > [On screen] >
[Split screen ID display]...

Installation-Related Menu Settings
158
Showing/Hiding the 
Test Pattern
> [Install settings] > [Test pattern]
You can project a test pattern (P291) 
to check resolution, color, and other 
details even without supplying an 
input signal.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• [Off] is the factory default.
• During test pattern display, you can use the 
[ ] / [ ] buttons to switch test patterns. 
Additionally, if a test pattern has option 
settings,...

Installation-Related Menu Settings
159
Installation and Maintenance
Installation
Projecting from Multiple Projectors at Once 
(Edge Blending)
> [Install settings] > [Professional 
settings] > 
[Edge blending]
Overlapping edges of images from 
multiple projectors used together 
can be blended to make the overall 
image more seamless.
■Basic Instructions
Follow these steps when using two projectors side by side.
1In the [Install settings] menu, select [Professional settings] > [Edge 
blending].
2Select...

Installation-Related Menu Settings
160
Here, you can use the following settings in the edge blending menu.
3Select the position where the images overlap.
When you are adjusting the left image, this area is along the right edge of the 
image. In the edge blending window, select [Right] > [Adjust].
4Set [Marker] to [On].
Marker lines are projected on the images. The red marker indicates the start 
position for adjustment, and the green marker, the end position.
OffDoes not blend overlapping areas....