Canon Projector WUX450 User Manual

121
Customizing System Operation (System Settings)
Operation
Setting Functions from Menus
Updating the 
Firmware
> [System settings] > [Other settings] > 
[Firmware]
Use a firmware update program 
stored on a USB flash drive to 
update the projector firmware.
Download firmware updates from the 
Canon website and store them at the 
root directory on the USB flash 
drive.
Select [Firmware], press the OK button, 
and check the firmware version 
displayed. Selecting [OK] will display an 
update confirmation...

122
Checking Projector Information
> [Information]
You can check information about the 
signal types of the images projected 
and other information.
Information shown
* Not displayed when network functions are [Off].
HDMIComponentLAN
Digital PCAnalog PCUSB
ItemExplanation
Model nameWUX450/WX520/WUX400ST/WX450ST
Input signalDetails of the input signal currently selected 
Information such as the type, resolution, and frequency of 
the signal is displayed.
FirmwareCurrent firmware version
Serial no.Serial...

123
MULTIMEDIA PROJECTOR
Installation and 
Maintenance
Request projector installation from a qualified 
technician, if possible, or contact the Canon 
Customer Support Center. For ceiling installation in 
particular, always request installation from a qualified 
technician or contact the Canon Customer Support 
Center. 

124 

125
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from 
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Networked Multi-Projection
Networked Multi-Projection 
Overview
Operation in Each Mode
Functions in All Modes
AppendixOther Information
Index
Installation 

126
Before Installation
Precautions When Carrying/Shipping the 
Projector
Precautions for Installation
Be sure to read “Safety Instructions” and “For Safe Use” (P16 – P29). Also 
take the following precautions during installation.
Prepare the projector as described below before carrying it.
• Disconnect the cables connected to the projector. Carrying the 
projector with the cables attached may cause an accident.
• Retract the adjustable feet.
• Do not reuse any packaging or shock-absorbent materials that...

Before Installation
127
Installation and Maintenance
Installation
■Do Not Use in the Following Environments
•Do not install the projector in a location that is damp, or where there is a lot of 
dust, oily smoke or tobacco smoke. Optical parts such as the lens and mirror may 
be stained, resulting in poor picture quality.
•Do not install the projector near high-voltage electrical power lines or an electrical 
power source. The projector may not operate correctly.
•Do not use the projector on a soft...

Before Installation
128
■Be Careful of Condensation
If the temperature of the room rises suddenly, moisture in the air may condense on 
the projector lens and mirror, causing the image to become blurred. Wait until the 
condensation has evaporated for the image projected to return to normal.
■At Altitudes above 2,300 m (7,545.8), Adjust the Settings
Projector settings must be adjusted when using the projector at altitudes of 2,300 m 
(7,545.8) or higher. Specifically, refer to instructions for [Fan mode]...

Before Installation
129
Installation and Maintenance
Installation
■Install Facing in the Correct Direction
When installing the projector facing upward or downward, specify which way the projector 
is facing in [Install settings] > [Professional settings] > [Vertical projection]. (P152)
10°  10°
10°  10°
10°
10°
The projector can be installed facing any direction*1, as shown 
below. However, projection upward ( ) or downward ( ) may 
shorten the useful life of the lamp. Installation in these orientations...

130
Installation Procedure
Setting Up the Projector
■Positioning the Projector in Front of the Screen
Place the projector in front of the screen.
■Floor Installation
To adjust the projection position when the projector is installed on the floor, use the 
lens shift function (P58 and P134) to adjust up / down / left / right. You can also use 
the adjustable feet to incline the projector upward by up to 6°.
For information about the relationship between screen size and projection distance, 
refer to page...