Canon Projector WUX450 User Manual

71
Operation
Projecting an Image
Step 6 Select the Image Quality (Image Mode)
You can select an image mode to suit the projected image.
In each image mode, you can further adjust the brightness, contrast, sharpness, 
gamma, color adjustment, advanced adjustment, and lamp mode. (P97)
Image Modes
The image modes which can be selected vary somewhat depending on the 
selected input signal.
Image 
Mode
Compatible input signals
Explanation
Digital PC
Analog PC-1 / 2
HDMI (when 
[HDMI In] is 
[Computer])
LAN...

Step 6 Select the Image Quality (Image Mode)
72
■Selecting an Image Mode
Press the IMAGE button on the remote control to select.
The image mode changes each time the IMAGE button is pressed. (The displayed 
image modes vary depending on the selected input signal.)
You can also select any image mode from the [Image mode] menu. (P97)
•User settings 1 - 5 are displayed when the desired image settings have been 
created and stored using the user memory function in the image adjustment 
menu (P98).
Remote...

73
Operation
Projecting an Image
Step 7 Set Power-Saving Settings
Press the ECO button on the remote control to complete power-saving settings.
The following three settings are available.
•Lamp Settings
For changing lamp and fan power consumption in the current image mode.
• Auto Power-Off
A function for automatically turning the power off after a certain period if the 
projector is not used and there is no input signal.
• Network Standby Settings
Specify whether network functions should be active in...

74
Step 8 Turn the Projector Off
1Press the POWER button to display the window shown below.
2When this window is displayed, press the POWER button again to turn off 
the power.
After you turn the power off, the projector will enter standby mode once it cools 
down.
If you want to continue projecting without turning off the power, press a button other than 
POWER, or else wait until the confirmation message disappears.
• After turning off the projector, wait at least 5 minutes before turning it on again....

75
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from 
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Networked Multi-Projection
Networked Multi-Projection 
Overview
Operation in Each Mode
Functions in All Modes
AppendixOther Information
Index
Useful Functions 
Available During a 
Presentation 

76
Useful Presentation Functions
Temporarily Blacking 
Out an Image
Press the BLANK button to black out 
the image.
Press the BLANK button again to show 
the image.
• You can set the screen state while blacking 
out the image in the menu. (P109)
• The lamp remains illuminated while the 
image is blacked out.
Freezing the Picture
Press the FREEZE button to freeze the 
moving image. The projector shows the 
following icon.
Press the FREEZE button again to 
return to the original display.
• It is also...

77
Useful Presentation Functions
Operation
Useful Functions Available During a Presentation
Adjusting the Volume
Press the VOL button. The following 
screen appears.
• You can also adjust the volume level with 
the [ ] / [ ] buttons of the projector.
• Adjust the volume or mute setting on the 
computer if the volume level is too low.
• You can also adjust the volume level of the 
speakers connected via the audio output 
terminal.
Muting the Sound
Press the MUTE button to mute the 
sound. The projector...

78
Useful Presentation Functions
Zooming an Image
Press the +D.ZOOM button to enlarge 
a part of the image. Press the 
–D.ZOOM button to reduce the image 
size.
• The magnification appears on the screen.
You can move the enlarged area by 
using the [ ] / [ ] / [ ] / [ ] buttons.
You can restore the original size of the 
image by pressing the OK button. Useful when:
• Zooming in on an object such as a 
small graph during a presentation (up 
to 12x).
• Focusing on the current subject.
Screen Remote...

79
Operation
Useful Functions Available During a Presentation
Projecting Images on a USB Flash Drive
Images stored on a USB flash drive in the projector can be projected as follows. 
You can select the images to project, or you can project images automatically, one 
after another. JPEG images up to 7000x7000 can be projected.
1Insert the USB flash drive in the USB port.
Insert the USB flash drive directly into the projector’s USB port. The USB flash 
drive will not be recognized if you connect it via a...

80
Projecting Images on a USB Flash Drive
4Use the pointer buttons to select a file, and then press the OK button to 
project the image.
Press the [ ] / [ ] buttons to select a file.
To view another page, press the [ ] / [ ] buttons (if other pages are available).
To navigate to a higher or lower folder, select a folder and press the OK button.
5Switch to other images as needed.
To switch to the previous image, press the [ ] button.
To switch to the next image, press the [ ] button.
To rotate images left...