Canon Projector WUX450 User Manual

31
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from 
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Networked Multi-Projection
Networked Multi-Projection 
Overview
Operation in Each Mode
Functions in All Modes
AppendixOther Information
Index
Before Use 

32
Supplied Accessories
Check that the following accessories have been supplied with the projector.
• Remote control • Batteries for the remote control
(AAA size x2)
(part No.: RS-RC06)
Optional remote controls are 
also available (RS-RC04, RS-
RC05). However, some buttons 
are not supported with this 
projector. The RS-RC05 can 
also be used as a wired remote. 
( P36 )
• Computer cable (1.8 m / 5.9)
(mini D-sub 15-pin / mini D-sub 15-pin) • 
Power cord (1.8 m / 5.9)
For Continental 
Europe
•  User’s...

33
Supplied Accessories
Before Use
■Attaching the Lens Cap
When using the WUX450/WX520, align the l ens cap notch with the optical zoom 
adjustment lever as shown and attach the cap.
There is no need to align the lens  cap when using the WUX400ST/WX450ST.
Always remove the cap before 
projection. Accidentally leaving the 
cap on during projection may distort 
the cap and damage the projector. 

34
Preparing the Remote Control
■Installing Remote Control Batteries
• If buttons on the remote control are inoperative when you attempt to operate the 
projector, replace the batteries with new ones.
• Do not drop the remote control or subject it to impact.
• Do not spill any liquids on the remote control. Doing so could damage it.
Pay attention to the following points when handling the batteries. 
Failing to do so could result in a fire or personal injury.
• Do not heat, short circuit or disassemble...

35
Preparing the Remote Control
Before Use
■Remote Control Operating Range
The remote control is an infrared type. Point it at the infrared remote receiver on the 
front or rear of the projector to operate it.
• Use the remote control within an angle of 25° in any direction from directly in front of the 
infrared remote receiver.
• The remote control may be inoperative if there is an obstacle between the remote 
control and the projector or the infrared remote receiver on the projector is exposed to...

Preparing the Remote Control
36
■Using an Optional Wired Remote (RS-RC05)
To use a wired remote control with the projector, use the RS-RC05, sold separately.
Use a cable with a ø3.5 mm stereo mini jack (not included).
• Infrared operations cannot be performed if a cable is connected to the projector or the 
remote control.
• Use a cable with a ø3.5 mm stereo mini jack (not included) with a length of 30 m (98.4) 
or less.
ø3.5 mm stereo mini jack 
cable (not included)Terminal for wired 
remote control...

37
Before Use
Part Names
Projector (WUX450/WX520)
■Front Side
■Rear Side
■Bottom Side
Terminals and 
connectors (P44)Projection lens (P45)
Power cord connector 
(P143) Side control
(P42)
Air intake vent
Air filter (P199)
• Do not block the air intake.
Doing so may cause a malfunction.
• Before projection, always remove the 
cap. Leaving the cap on may damage 
the projector.
Hole caps (P131)
Attach option feet (sold 
separately). For instructions 
on removing the hole caps, 
refer to “Attaching Option...

Part Names
38
Projector (WUX400ST/WX450ST)
■Front Side
■Rear Side
■Bottom Side
Terminals and 
connectors (P44)Projection lens (P45)
Power cord connector 
(P143) Side control
(P42)
Air intake vent
Air filter (P199)
Hole caps (P131)
Attach option feet (sold 
separately). For 
instructions on removing 
the hole caps, refer to 
“Attaching Option Feet (RS-
FT01, Sold Separately)”.
Infrared remote receiver (P35)
Do not block the air intake.
Doing so may cause a malfunction.
Exhaust vent
Infrared remote...

39
Part Names
Before Use
Mounting the Projector on the 
Ceiling
You can mount the projector on the 
ceiling.
The ceiling attachment (part No.: RS-
CL12 (WUX450/WX520), RS-CL13 
(WUX400ST/WX450ST)) is required 
in order to mount the projector on the 
ceiling. Depending on the installation 
environment, an extension pipe (part 
No.: RS-CL08 or RS-CL09) may also 
be required. Contact the Canon 
Customer Support Center for more 
detailed information.
If you mount the projector on the 
ceiling, you have to...

40
Part Names
Remote control
The projector can be operated using buttons on the remote control or the side 
control on the projector.
The remote control allows you to operate all functions of the projector.
POWER button (P52, P74)
Turns the projector on or off.
ASPECT button (P67)
Changes the aspect ratio mode.
KEYSTONE button (P68)
Corrects keystone distortion.
The [Keystone] setting enables both 
horizontal/vertical keystone correction 
(by adjusting top/bottom/left/right 
length) and corner...