Canon printer PIXMA MP800R User Manual

							Chapter 1 39Before Printing
Ta b  2
Allows you to optimize photos with the functions below.
(1)Red eye correction ON, Red eye correction OFF
*1
When  is selected, portraits with a red eye caused by flash 
photography are corrected in print.
(2)Activate/deactivate Vivid photo function.
*1
This function makes green and blue more lively.
Vivid photo ON, Vivid photo OFF
(3)Activate/deactivate the Photo Optimizer pro function.
*1
This function automatically optimizes brightness and tone of a photo.
Photo optimizer pro ON, Photo optimizer pro OFF
(4)Activate/deactivate the Noise reduction function.
*1
This function reduces the noise on blue areas like the sky as well as on black areas.
Noise reduction ON, Noise reduction OFF
(5)Activate/deactivate Face brightener function.
*1
This function brightens a darkened face on the photo taken against the light.
Face brightener ON, Face brightener OFF
(6)Choosing  enables you to correct and smooth the jagged contours 
for printing.
*1
Image optimizer ON, Image optimizer OFF
(7)Adjust brightness.*1
Brightness +2, Brightness +1, Brightness standard, Brightness -1, Brightness -2
(8)Adjust contrast.*1
Contrast +2, Contrast +1, Contrast standard, Contrast -1, Contrast -2
(9)Adjust color hue.*1
Color hue red +2, Color hue red +1, Color hue original, Color hue yellow +1, Color hue 
yellow +2
(10)Select the type of special effects applied to the photo, such as printing in sepia tones or 
with a sketch illustration like effect.
*1
No effects, Sepia, Simulate illustration
(11)Choosing  corrects the color when printing photos that have faded or 
color cast over time.
Choosing  brightens a darkened face on a portrait taken against the 
light.
*2
No image enhancement, Fade restoration, Face brightener*1 Can be selected only in Memory card mode.*2 Can be selected only in Photo/film mode.
(1)(2)(3)(4)
(6)(7)(8)(9)
Memory card mode Photo/film mode
(5)
(11)
(10) 
						

							Chapter 2
40Chapter 2Copying
Copying
Making Copies
This section describes the basic procedure to make copies.
1Prepare for copying.
(1)Press [ON/OFF] to turn on the machine.
See“Turning on the Machine” on page 18.
(2)Press [COPY].
(3)Load paper.
See“Loading Paper” on page 20.
(4)Ensure that the proper paper source is selected.
See“Changing the Paper Source” on page 24.
(5)Load the document on the Platen Glass.
2Start copying.
(1)Check the page size and media type.
(2)Use [ ] or [ ] to specify the number of copies.
The following information is displayed as well.
Note
Specify [Feed Switch] so that the Auto Sheet Feeder Lamp is lit when feeding paper from the 
Auto Sheet Feeder and the Cassette Lamp is lit when feeding paper from the Cassette.
Note
For information on the types and conditions of documents which you can copy, see “Loading 
Documents” on page 19.
Note
Press [Settings] to check or change the page size, media type, or other settings. See “To 
Change Print Settings” on page 35.
Intensity: Pressing [ ] decreases the intensity, and pressing [ ] increases the 
intensity.
You can also use the auto intensity. See “Print Setting Items” on page 37.
(1)(2) 
						

							Chapter 2 41Copying
(3)Press [Color] for color copying, or [Black] for black & white copying.
The machine starts copying.
„Reducing or Enlarging a Copy
You can reduce or enlarge copies.
1Prepare for copying.
See “Prepare for copying.” on page 40.
2Select the reduction/enlargement method.
The example below assumes that you will select .
(1)Press [Settings].
(2)Use [ ] or [ ] to select Tab 1.
(3)Use [ ] or [ ] to select , and use [ ] or [ ] to select .
Specify the custom copy ratio for reducing or enlarging copies.
Besides , you can also choose from the following reduction/
enlargement methods.
(4)Press [ ] to move the cursor down, and use [ ] or [ ] to select the setting value. 
Holding down [ ] or [ ] steps through the values faster.
3Finalize your selection.
(1)Press [Settings].
Return to the Copy standby screen.
4Start copying.
See “Start copying.” on page 40.
Note
To cancel copying, press [Stop/Reset].
Same magnification: Copies in the same size as an original.
Preset ratio: Preset ratios are convenient when changing between standard page sizes, 
for example, when reducing A4 to A5, or enlarging B5 to A4.
Fit-to-page: You can automatically reduce or enlarge the document to fit the size of the 
paper which are loaded in the Auto Sheet Feeder or Cassette.
Note
When you choose , the document size may not be detected correctly depending 
on the document. In that case, choose ,  or .
(3) 
						

							42Chapter 2Copying
Changing the Copy Settings
You can change the copy settings such as the page size, media type, or print quality.
For details on changing the copy settings and setting items, see “To Change Print Settings” on 
page 35.
1You can specify the page size.
2You can specify the media type.
3You can adjust print quality for the document to be copied.
4You can specify the reduction/enlargement method.
See “Reducing or Enlarging a Copy” on page 41.
5You can specify if auto intensity is performed.
Specifying  automatically changes the icon above the intensity slide bar 
on the LCD to .
Important
Even while  is selected, you can change the intensity by pressing [ ] or 
[ ]. Move the cursor to the center of the slide bar to enable auto intensity again.
1234
5 
						

							Chapter 2 43Copying
Using Useful Copy Functions
„Special Copy
You can copy in various layouts.
1Prepare for copying.
See “Prepare for copying.” on page 40.
2Select the copy menu.
(1)Press [Menu].
(2)Use [ ] or [ ] to select , then press [OK].
The Special copy screen is displayed.
zCopying onto Both Sides of the Paper (Two-sided copy)
You can copy two document pages onto the sides of a single sheet of paper.
Long-side stapling and Short-side stapling
Procedure:
(1)Display the Special copy screen.
See“Special Copy” on page 43.
(2)Use [ ] or [ ] to select , then press [OK].
(3)Use [ ] or [ ] to select the orientation of the document, then press [OK].
(4)Use [ ] or [ ] to select the binding margin, then press [OK].
(5)Follow the on-screen instructions to load the document to be printed on the front face on 
the Platen Glass, then press [OK].
(6)Specify the necessary items.
See“To Change Print Settings” on page 35.
(7)Press [Color] for color copying, or [Black] for black & white copying.
(8)Load the document to be printed on the back face on the Platen Glass. If you have only 
one document to scan, press [OK].
(9)Press [Color] or [Black]. Be sure to press the same button as you pressed in step (7).
(2) 
						

							44Chapter 2Copying
zCopying Two Pages to Fit onto a Single Page (2-on-1 copy)
This feature enables you to copy two documents (A) (B) onto a single sheet (C) of paper by 
reducing each image.
Procedure:
(1)Display the Special copy screen.
See“Special Copy” on page 43.
(2)Use [ ] or [ ] to select , then press [OK].
(3)Follow the on-screen instructions to load the document to be printed on the left side on 
the Platen Glass, then press [OK].
(4)Specify the necessary items.
See“To Change Print Settings” on page 35.
(5)Press [Color] for color copying, or [Black] for black & white copying.
(6)Load the document to be printed on the right side on the Platen Glass. If you have only 
one document to scan, press [OK].
(7)Press [Color] or [Black]. Be sure to press the same button as you pressed in step (5).
Important
If you do not press the same button in step (7) and step (9), the machine does not start 
copying.
Note
zThis function cannot be used in conjunction with  under  or 
other copy functions.
zIf you perform black & white copying for , print intensity may be different 
from when performing black & white copying for single-sided copy.
zThis function can only be used when the page size is set to  or 
.
zThe media type is fixed to . You cannot change this setting.
Important
If you do not press the same button in step (5) and step (7), the machine does not start 
copying.
(A) (C) (B) 
						

							Chapter 2 45Copying
zCopying Four Pages to Fit onto a Single Page (4-on-1 copy)
This feature enables you to copy four documents onto a single sheet of paper by reducing each 
image. Four types layouts can be selected.
Procedure:
(1)Display the Special copy screen.
See“Special Copy” on page 43.
(2)Use [ ] or [ ] to select  and press [OK].
(3)Use [ ] or [ ] to select the layout, then press [OK].
(4)Follow the on-screen instructions to load the first document to print on the Platen Glass, 
then press [OK].
(5)Specify the necessary items.
See“To Change Print Settings” on page 35.
(6)Press [Color] for color copying, or [Black] for black & white copying.
(7)Load the second document to print on the Platen Glass, and press the same button as 
you pressed in step (6).
(8)Repeat step (7) until you finish loading the fourth document, then press the same button 
as you pressed in step (6). If you have only one, two or three documents to scan, press 
[OK] after loading the last document.
Note
zThis function cannot be used in conjunction with other functions.
zIf  appears on the LCD when scanning, set the print quality to 
 and try copying again.
zYou can use this feature only when the page size is set to  or 
. 
zYou cannot select .
Important
If you do not press the same button in step (6), steps (7) and (8), the machine does not start 
copying.
Note
zThis function cannot be used in conjunction with other copy functions.
zIf  appears on the LCD when scanning, set the print quality to 
 and try copying again.
zThis function can be used only when page size is set to  or 
.
zYou cannot specify  for this function. 
						

							46Chapter 2Copying
zCopying without Borders (Borderless copy)
This feature enables you to copy images so that they fill the entire page without borders.
Procedure:
(1)Display the Special copy screen.
See“Special Copy” on page 43.
(2)Use [ ] or [ ] to select , then press [OK].
(3)Specify the necessary items.
See“To Change Print Settings” on page 35.
(4)Press [Color] or [Black] to start copying.
zRepeating an Image on a Page (Image repeat)
This feature enables you to copy an image multiple times onto a single page. You can set the 
machine to automatically select the number of times it repeats the image, or you can specify the 
number.
Procedure:
(1)Display the Special copy screen.
See“Special Copy” on page 43.
(2)Use [ ] or [ ] to select , then press [OK]. 
(3)Use [ ] or [ ] to select  or .
If you selected  and pressed [OK], go to step (7).
If you selected  and pressed [OK], go to step (4).
(4)Use [ ] or [ ] to set the vertical repeats.
Note
zThe copied image may need to be enlarged to fit onto the selected page size when making 
borderless copies. Some cropping may occur.
zYou can use this feature only when the page size is set to , 
, , , or .
zYou can use this feature only when the paper is set to , , , .
zYou can specify print quality to either  or .
zYou can select the width to be cropped from the borders of the original image according to 
the image size. 
						

							Chapter 2 47Copying
(5)Press [ ] to move the cursor to the right.
(6)Use [ ] or [ ] to set the horizontal repeats, then press [OK].
(7)Specify the necessary items.
See“To Change Print Settings” on page 35.
(8)Press [Color] for color copying, or [Black] for black & white copying.
Important
zThe area read from the documents depends on the enlargement/reduction ratio.
zThe size of the documents to copy should be no larger than one division of the paper. For 
example, if you copy four documents at the same size, their sizes must be one-fourth of 
the page size or smaller.
Note
z cannot be selected for the page size.
z cannot be selected for . 
						

							Chapter 3
48Chapter 3Printing from a Memory Card
Printing from a Memory Card
Using the Memory Card
This section describes the compatible memory cards and how to insert and remove them.
„Memory Cards Supported by This Machine
The following memory cards are compatible with this machine. 
Memory cards that can be directly inserted into the Card Slot:
zCompact Flash (CF) Card
Supports Type I/II (3.3V)
zMicrodrive
zSmartMedia
Supports 3.3V card only
1MB and 2MB cards are not supported
zMEMORY STICK
zMEMORY STICK PRO
zSD Secure Digital memory card
zMultiMedia Card
Memory cards that can be inserted in the Card Slot using the adapter:
xD-Picture Card*1
zMEMORY STICK Duo*2
zMEMORY STICK PRO Duo*2
miniSD Card*2