Canon Lbp 3000 User Guide

							Replacing the Toner Cartridge5-18
Routine Maintenance
5
•Do not attempt to disassemble or modify the toner cartridge.
•If you expose a toner cartridge to rapid changes in temperature, droplets of water 
(condensation) may form on the interior and exterior of the cartridge. If a new toner 
cartridge that has been stored in a cool location is going to be installed in a warm area, 
leave the cartridge for at least one hour without opening the protective bag to allow the 
cartridge to adjust to the surrounding temperature before opening the bag.
•Be sure to use new toner cartridges within the expiration date indicated on the package.
•Keep toner cartridges away from products that generate magnetic waves, such as the 
computer or monitor.
•Toner cartridges are magnetic parts. Do not bring toner cartridges near floppy disks, disk 
drives, or other magnetic-sensitive devices. Doing so may cause data corruption.
Storing Toner Cartridges
Be careful of the following points when storing a new toner cartridge or handling a 
toner cartridge that has been taken out of the printer for maintenance or moving the 
printer.
IMPORTANT
•Do not take a new toner cartridge out of the protective bag until it is ready to be used.
•If you take the toner cartridge out of the printer to remove a paper jam or service the 
printer, place the toner cartridge into the original protective bag, or wrap it in a thick cloth 
immediately.
•Do not stand it on its end, or turn it upside down. Store the cartridge in the same direction 
as when it is installed in the printer.
•Do not store the toner cartridge in a place exposed to direct sunlight.
•Do not store the toner cartridge in a hot or humid place, or a place where the 
temperature and humidity can change significantly.
-Storage Temperature Range: 0 to 35°C (32 to 95°F)
-Storage Humidity Range: 35 to 85%RH (non-condensing)
•Do not store the toner cartridge in a place where corrosive gases, such as ammonia, are 
generated, or where a considerable amount of salt is contained in the air, or where there 
is a lot of dust.
•Keep toner cartridges out of the reach of small children.
•Do not store toner cartridges near floppy disks, disk drives, or other magnetic-sensitive 
devices.
■Condensation
Even when the humidity is within the storage range, water droplets may form on the inside 
or outside of the toner cartridge due to temperature differences with the surrounding air. 
This condensation will have a bad effect on the performance of the toner cartridge.
 
						

							Clean the outside of the printer5-19
Routine Maintenance
5
Clean the outside of the printer
If dirt and dust builds up on the outside of the main unit after you use the printer for 
a long period of time, you should clean the printer. To avoid damage to the printer 
and electrical shocks while cleaning, observe the following precautions when 
cleaning.
WARNING
•Turn the printer off and remove the plug from the wall when you are cleaning the 
printer. Failure to do so may cause fire or electrical shock.
•Do not use alcohol, benzene, thinners or any other inflammable substance. If an 
inflammable substance comes into contact with the electrical unit inside the 
printer it may ignite or cause an electrical shock.
IMPORTANT
•Be careful not to use a cleaning agent other than water or a mild detergent mixed with 
water as it may deform or crack the plastic materials in the printer.
•When using a mild detergent, be sure to dilute it with water.
•This printer does not need to be lubricated. Do not lubricate the printer.
1Turn the printer and computer off aa a a, remove the USB cable bb b b, 
and disconnect the power plug from the power outlet 
cc c c.
a
c
b
a
 
						

							Clean the outside of the printer5-20
Routine Maintenance
5
2Firmly wring a soft cloth dampened with water or a mild 
detergent diluted with water, and wipe off the dirt.
If you use a mild detergent for cleaning, be sure to wipe away the detergent with 
a soft cloth dampened with water.
3After wiping off the dirt, wipe the printer with a dry cloth.
4Once the printer is completely dry, plug the power plug into 
the power outlet and reconnect the USB cable.
 
						

							Moving the Printer5-21
Routine Maintenance
5
Moving the Printer
When changing the location of the printer or moving the printer for maintenance, be 
sure to use the following procedure.
WARNING
When you are moving the printer, always turn the printer off, unplug the power 
plug, and remove the USB cable. If you move the printer without unplugging the 
cables, the electrical cord and USB cable may be damaged, causing a fire or 
electrical shock.
CAUTION
•The printer weighs approximately 6.3 kg when the tray cover is not installed. 
Take care to carry the printer without hurting your back.
•Never hold the printer by the front panel, ventilation slots, rear panel, or 
anywhere else other than the specified locations. Doing so may cause the 
printer to fall, resulting in personal injury.
 
						

							Moving the Printer5-22
Routine Maintenance
5
Moving the Printer
Use the following procedure to move the printer.
1Turn the printer and computer off aa a a, remove the USB cable bb b b, 
and disconnect the power plug from the power outlet 
cc c c.
2Remove the power cord.
3Remove the tray cover.
a
c
b
a
 
						

							Moving the Printer5-23
Routine Maintenance
5
4Clear out any paper that is loaded in the printer, and push the 
rear paper guide in to the position shown in the diagram.
IMPORTANT
If you try to close the multi-purpose tray while the rear paper guide is sticking out of 
the tray, you may damage the printer. Always check to make sure that rear paper 
guide is pushed all the way back into the multi-purpose tray before you close the 
multi-purpose tray.
5Close the multi-purpose tray.
 
						

							Moving the Printer5-24
Routine Maintenance
5
6If the paper output tray is open, close it.
7Grasp the left and right side of the printer with your hands, as 
shown in the diagram, and firmly hold onto the printer when 
you carry it.
8Put the printer down carefully at the installation site.
CAUTION
Put the printer down slowly and carefully. You may be injured if your 
hands, etc. are pinched by the printer.
 
						

							Moving the Printer5-25
Routine Maintenance
5
9Open the output tray.
10Open the multi-purpose tray.
11Load the Paper
Refer to Printing on Plain Paper, Heavy Paper, Label Paper, and Transparencies, 
on p. 2-14 for information on loading plain paper, heavy paper, label paper and 
transparencies.
Refer to Printing on Index Card, on p. 2-27 for information on loading index 
card.
Refer to Printing on Envelopes, on p. 2-34 for information on loading envelopes.
Refer to Printing on Custom Paper Sizes (Non-Standard Sizes), on p. 2-45 for 
information on loading custom paper sizes.
 
						

							Moving the Printer5-26
Routine Maintenance
5
12Attach the tray cover.
Attach the tray cover so that the protrusions on the left and right sides of the 
cover fit into the grooves in the main body.
13Connect the power cord.
14Plug the power plug into the AC power outlet.
15Connect the USB cable.
●Transporting the Printer
When transporting the printer for reasons such as relocating, remove the toner 
cartridge and store the printer and parts in the packages that they came in with 
the protective materials attached in order to prevent them from being damaged 
while being transported.
If the original package and packing materials are not available, find an 
appropriate box and packing materials and pack the printer and the parts 
appropriately.
Tr a y  cover
Protrusion
Groove
 
						

							Handling the Printer5-27
Routine Maintenance
5
Handling the Printer
This printer uses a variety of electronic components and delicate optical 
components. Read the following section carefully, and take care when handling the 
printer.
IMPORTANT
Information on handling the printer is also described in Important Safety Instructions, 
on p. xiv.
Precautions for Handling the Printer
Observe the following precautions to allow your printer to consistently produce 
high-quality printing.
IMPORTANT
•Do not place any heavy objects on top of the printer, output tray, tray cover, or other part 
of the printer. Doing so may damage the printer.
•If you try to close the multi-purpose tray while the rear paper guide is sticking out of the 
tray, you may damage the printer. Always check to make sure that rear paper guide is 
pushed all the way back into the multi-purpose tray before you close the multi-purpose 
tray.
•Do not leave the top cover open for any longer than you need to. Exposure to direct 
sunlight or strong light can degrade the printer performance.