Canon Laser Shot Lbp3500 User Guide

 
6-34 
Optional Accessories
 
6 
Network Board 
  
Installing the Network Board 
Install the network board in the expansion slot of the printer using the following 
procedure. A Phillips screwdriver is required for installing the network board. Have 
a screwdriver ready in advance that matches the size of the screws.
NOTE
 
This network board does not come with a LAN cable. A Category 5 twisted pair cable is 
required for installing the network board and connecting the printer to a network. Have 
cables...

6-35
Optional Accessories
6
Network Board
3Remove the screw and remove the protective plate for the 
expansion slot.
IMPORTANT
The removed protective plate and screw are required when the network board is 
removed. Keep them where they will not get lost.
4Insert the network board into the expansion slot.
Hold the metal panel portions of the network board and insert the board while 
aligning it with the guide rails inside the expansion slot.
IMPORTANT
•Do not touch the network board parts, printed wire,...

 6-36 
Optional Accessories
 6 
Network Board 
5
  Secure the top and bottom portions of the network board with 
the two screws supplied with the network board. 
6
 
If you are using NB-C1, attach the ferrite core to the LAN cable 
as shown in the figure. 
Attach the ferrite core at 5 cm or less from the end of the connector which is 
connected to the printer.
5 cm or less
 

6-37
Optional Accessories
6
Network Board
7Connect the LAN cable.
Connect a LAN cable that is compatible with the LAN connector of the network 
board according to the network.
8Connect the power cord.
9Plug the power plug into the AC power outlet.
10Connect the USB cable as needed.
11Press   of the power switch to turn the printer ON.
IMPORTANT
If the printer does not operate properly, or an error message appears in the Printer 
Status Window, see Troubleshooting, on p. 7-1.
 

 6-38 
Optional Accessories
 6 
Network Board 
12
  Make sure that the LNK indicator (green) on the network 
board is on. 
If the network board is connected by 10BASE-T, the board is working properly 
when the LNK indicator is on.
If the network board is connected by 100BASE-TX, the board is working properly 
when the LNK indicator and 100 indicator are on.
((A): ERR Indicator (B): LNK Indicator (C): 100 Indicator)
 
If the network board is not working properly, turn the printer OFF, and then check 
the...

 6-39 
Optional Accessories
 6 
Network Board Setting the Network Board 
The default value of the network board is set at Auto detect. Usually, you do not 
need to change the setting, since the transmission speed and transfer mode of 
10BASE-T/100BASE-TX are detected automatically. If the printer cannot 
communicate with other devices on the network, set the DIP switches on the 
network board. Before setting the DIP switches, turn the printer OFF, then remove 
the network board. A Phillips screwdriver is...

6-40
Optional Accessories
6
Network Board
■Setting the Network Transmission Speed/Transfer Mode and the DIP 
Switches
1Turn the printer and computer OFF, remove the USB cable, 
and then disconnect the power plug from the AC power outlet.
2Remove all the interface cables and the power cord from the 
printer.
3Remove the two screws and remove the network board.
IMPORTANT
Do not touch the network board parts, printed wire, or connectors with your hands.
Communication speed and 
Transmission mode of LAN...

 6-41 
Optional Accessories
 6 
Network Board 
4
 Set the DIP switches. 
Set the DIP switches with the tip of a ball-point pen etc. For details o\
n methods 
for setting the DIP switches, see the table of p. 6-40. 
5
 
Insert the network board into the expansion slot. 
Hold the metal panel portions of the network board and insert the board while 
aligning it with the guide rails inside the expansion slot.
IMPORTANT
 
•
 
Do not touch the network board parts, printed wire, or connectors with your hands....

6-42
Optional Accessories
6
Network Board
Problems on Installing the Network Board
On checking the operation of the network board, if you find that all the indicators on 
the network board are off, or the ERR indicator is on or keeps blinking for a long 
time and does not go off, take the following measures.
NOTE
For details on problems on installing the CAPT software, see Chapter 4 
Troubleshooting in Network Guide.
All the indicators on the network board are off.
Cause 1 The LAN cable is not connected...

6-43
Optional Accessories
6
Network Board
The ERR indicator on the network board is on.
Cause The network cable is disconnected or broken, or the network board is not 
installed properly.
Remedy 1 Make sure the network cable is connected properly.
Remedy 2 Replace the network cable with a proper one and check if there is no 
disconnection or damage.
Remedy 3 If the ERR indicator still comes on even after applying the Remedy 1 and 2, 
contact your local authorized Canon dealer for servicing.
The ERR...