Canon Imageprograf Ipf825 User Guide

Important
• Do not touch the Linear Scale (a), Carriage Shaft (b), or Ink Tube Stabilizer (c). Touching these parts
may damage them. 2.
With 
a  sheet  lengthwise  and  printing-side  up,  insert  it  between  the  Platen  (a)  and  the  Paper  Retainer  (b).  Align  the
edges of the sheet as follows.
1. Align the sheet with the Paper Alignment Line (c) at right.
2. Align the inserted edge of the sheet with the leading edge of the Paper Alignment Line (d), as shown. Handling Paper 
> Handling sheets >...

When inserted, sheets are automatically held by suction against the Platen.
Important
• Load a  sheet  so  that  it  is  parallel  to  the  Paper  Alignment  Line  at  right  (c).  Loading  paper  askew  will
cause an error.
• Warped paper may rub against the Printhead. Straighten paper if it is warped before loading it. Note
• You 
can adjust the strength of suction holding paper against the Platen when the Release Lever is up.
If it is difficult to load paper, press the  ▲ or ▼ button on the Control...

Manually Loading Paper to the Position for Printing
When printing on non-standard sizes of paper or to specify a particular position to start printing, in the printer menu set
Width Detection to Off for the paper used.
Setting Width Detection to Off  will prevent paper from being automatically advanced to the position for printing. In this
case, manually load paper at the position for printing.
Instructions for manually loading paper at the position for printing when  Width Detection is set to Off are as...

2.
Keeping  the right edge of the paper aligned with the extended line of the Paper Alignment Line (a) on the right side
of the printer, load the paper so that the near edge is aligned with the groove (b) at the far end of the Platen.
In  this  case,  advance  the  paper  as  far  into  the  paper  feed  slot  as  possible  because  it  will  be  printed  starting  at  that
position. 3.
Lower the Release Lever and close the Top Cover.
4. If 

no  print  job  has  been  received  from  the  computer,...

Note
• If a print job received requires paper larger than the selected paper, it may soil the Platen. Removing Sheets
Remove sheets from the printer as follows.
1. Press the Load/Eject button. Note
• Paper cannot be ejected by using the  Load/Eject button when print jobs are in progress or during the
ink  drying  period.  Before  ejecting  paper,  press  the  Stop  button  to  cancel  printing,  print  job  process-
ing, or ink drying.
2. Press the OK  button to eject the paper. The paper is ejected from...

3.
As you hold the sheet, lift the Release Lever and remove the sheet. 4.
Lower the Release Lever. Handling Paper > Handling sheets >
Removing Sheets
iPF8257
670
 

Output Stacker
Wheeled Output Stacker ................................................................................................................................. 671
Using the Wheeled Output Stacker ............................................................................................................. 671Wheeled Output Stacker
An output stacker with casters, positioned in front of the printer. a.
Output Stacker
A cloth tray that catches ejected documents.
The Output Stacker can be opened and...

Positioning the Wheeled Output Stacker by the printer
1. Holding the Output Stacker Ejection Guides (a), move the stacker between the printer Stand. 2.
Lock the casters. Handling Paper > Output Stacker >
Using the Wheeled Output Stacker
iPF8257
672
 

Removing the Wheeled Output Stacker from the printer
Note
• If there is not enough space to move the Wheeled Output Stacker, remove any printed documents inside the
Output Stacker and fold the Output Stacker up.
1. Release the caster lock. Handling Paper 
> Output Stacker >
iPF825
Using the Wheeled Output Stacker 7
673
 

2.
Holding the Output Stacker Ejection Guides (a), move the stacker away from the printer. Handling Paper > Output Stacker >
Using the Wheeled Output Stacker
iPF8257
674