Canon Imageprograf Ipf825 User Guide

3.
Holding  the Roll Holder so that the side with the white gear faces the side of the Roll Holder Slot with a white gear,
load the Roll Holder shaft (a) into the grooves (b) on both ends of the Roll Holder Slot. Caution
• Be 
careful not to pinch your fingers between the Roll Holder shaft (a) and the guide grooves (b) when
loading rolls. Note
• For 
instructions  on  attaching  the  Roll  Holder  to  rolls,  see  "Attaching  the  Roll  Holder  to  Rolls."→P.629 Handling Paper 
> Handling rolls...

4.
Using both hands, pull out the roll evenly on both ends and insert it in the Paper Feed Slot (a). Advance the roll until
the buzzer sounds. Important
• Be 
careful not to soil the printing surface of roll paper as you insert it in the slot. This may affect the
printing  quality.  We  recommend  wearing  clean  cloth  gloves  when  handling  rolls  to  protect  the  print-ing surface.
• If the paper is wrinkled or warped, straighten it out before loading it.
• Load the roll so that there is no gap...

5.
Lower the Ejection Guide. 6.
Close the Top Cover. 7.
Press the OK button.
The paper is now advanced.
After you load a roll, the printer automatically shows a menu for selection of the type of paper on the Display Screen.
At this point, specify the type of paper.   (See "Selecting the Paper Type (Roll) .") →P.642
  Loading rolls in the Roll 2 (Lower) holder
Caution
• Do not detach the Roll Unit in the following cases.
• During printing
Vibration from removing the Roll Unit may affect the...

1.
Confirm that a roll is selected as the paper source.   (See "Selecting the Paper Source.") →P.641
2.
Holding the Roll Unit Lever (a), pull out the Roll Unit. Handling Paper > Handling rolls >
Loading Rolls in the Printer
iPF8257
638
 

3.
Holding  the Roll Holder so that the side with the white gear faces the side of the Roll Holder Slot with a white gear,
load the Roll Holder shaft (a) into the grooves (b) on both ends of the Roll Holder Slot. Caution
• Be 
careful not to pinch your fingers between the Roll Holder shaft (a) and the guide grooves (b) when
loading rolls. Note
• For 
instructions  on  attaching  the  Roll  Holder  to  rolls,  see  "Attaching  the  Roll  Holder  to  Rolls."→P.629 Handling Paper 
> Handling rolls...

4.
Pull out the roll evenly on both ends and insert it in the Paper Feed Slot (a). Advance the roll until the buzzer sounds. Important
• Be careful not to soil the printing surface of roll paper as you insert it in the slot. This may affect the
printing  quality.  We  recommend  wearing  clean  cloth  gloves  when  handling  rolls  to  protect  the  print-ing surface.
• If the paper is wrinkled or warped, straighten it out before loading it.
• Load the roll so that there is no gap between the right edge...

5.
In a crouching position, push the Roll Unit into the printer. 6.
Position the Wheeled Output Stacker by the printer.   (See "Using the Wheeled Output Stacker.") →P.671
7. Press the OK button.
The paper is now advanced.
After you load a roll, the printer automatically shows a menu for selection of the type of paper on the Display Screen.
At this point, specify the type of paper.   (See "Selecting the Paper Type (Roll) .") →P.642
Selecting the Paper Source
When advancing paper, press the...

Note
• If a  sheet  is  loaded  when  you  change  the  paper  source  to  a  roll,  " Eject  sheet?"  is  displayed.  Press  the  OK
button and remove the sheet.
• You cannot switch the paper source in the following situations:
• When the Message lamp is flashing
Check  the  message  on  the  Display  Screen  and  take  action  as  necessary.  (See  " Error  Messag-
es →P.886
.")
• When the Data lamp is flashing
Select the paper source after printing is finished.
• When a printer menu...

2.
Press ▲ or ▼ to select  Media Menu, and then press the  ▶ button.
3. Press ▲ or ▼ to select  Roll1(Uppr) Type or Roll2 (Lwr) Type, and then press the  ▶ button.
4. Press  ▲ or ▼ to select the type of paper loaded in the printer, and then press the  OK button.Note
• For details on types of paper, see the Paper Reference Guide.   (See "Types of Paper.") →P.623
 By
default, Plain Paper is selected.
• If you move the Release Lever, the setting automatically reverts to the previously selected...

2.
Press ▲ or ▼ to select  Media Menu, and then press the  ▶ button.
3. Press ▲ or ▼ to select  Roll1(Uppr)Lngth or Roll2(Lwr) Lngth, and then press the  ▶ button.
4. Press ▲ or ▼ to select the length of paper loaded in the printer, and then press the  OK button.
Specify the roll length as follows.
1. Press  ◀ or ▶ to move the cursor (_) to each field for entering numbers.
2. Press the ▲ or ▼ button to enter the value.
3. Repeat steps 1 and 2 to finish entering the value, and then press the  OK button....