Canon Fax L2000ip User Guide

Periodic Cleaning6-11
6
Maintenance
4Using a dry, lint-free cloth, wipe any dust off the silver metal plate 
of the transfer guide.
5While holding the green label, flip the transfer guide up to its full 
extent. Wipe the edge of the transfer guide with a soft, clean 
cloth, to remove toner and paper dust from both sides of the 
transfer guide.
Transfer Guide
Transfer GuideGreen Label
 

Periodic Cleaning6-12
Maintenance
6
6Wipe the silver metal strip a with a soft, clean cloth. Then, gently 
place the transfer guide b back into its original position.
IMPORTANT
 To avoid the deterioration of print quality, never touch the transfer charging roller when 
you clean the metal strip.
7Reinsert the toner cartridge into the main unit.
8Close the printer cover, lower the document output tray and 
document feeder tray. Then, connect the power cord of the main 
unit to the power source.
2
1...

Periodic Cleaning6-13
6
Maintenance
Cleaning the Scanning Area
Periodically check the scanning glass, the white scanning strip, and rollers. If the underside of 
the ADF (Automatic Document Feeder) cover or the scanning glass is dirty, the documents you 
send may look dirty.
Check if some streaked lines which do not exist on the original appear on the output when 
scanning the original using the ADF.
If such lines appear, the scanning area may be dirty.
Follow the procedure described below to clean the...

Periodic Cleaning6-14
Maintenance
6
2Gently open the top unit of the ADF cover, as shown in the 
illustration below.
CAUTION
 Be sure not to open the ADF cover fully to the extent that the lower unit is lifted, as 
shown in the illustration on the right. The lower unit may fall heavily when you 
unlock the ADF cover in step 3.
Top Unit
Lower 
Unit Correct
Incorrect
Lower unit is not lifted.Lower unit is lifted.
 

Periodic Cleaning6-15
6
Maintenance
3Release the top unit of the ADF cover by pushing the hook inside 
with your finger or a pencil.
4Open the top unit of the ADF cover, and clean all the rollers.
Use a dry cloth to wipe clean the underside of the ADF cover and to wipe up 
the paper dust around the rollers.
Rollers
 

Periodic Cleaning6-16
Maintenance
6
5Gently close the top unit of the ADF cover until you hear it lock.
CAUTION
 Make sure that the top unit of the ADF cover is locked into position securely 
before proceeding to step 6.
6Lift the document feeder tray, and gently open the ADF cover 
until it stops, grasping the document feeder tray and the ADF 
cover at the same time.
 

Periodic Cleaning6-17
6
Maintenance
7While holding the ADF cover open with one hand, use one finger 
of your other hand to gently push in the black, plastic loop to 
separate it from the stub on the machine.
8Gently lift the ADF cover up to its full open position.
 

Periodic Cleaning6-18
Maintenance
6
9Use a soft, dry cloth to wipe clean the scanning glass, the white 
strip above, the rollers, and the area around the scanning glass. 
Use a soft, dry cloth that will not scratch the scanning glass to wipe clean the 
underside of the ADF cover and to wipe up the paper dust around the rollers.
NOTE
 If you have installed the optional stamp kit, be careful not to touch the stamp ink 
compartment when cleaning the scanning area.
10Lower the ADF cover until the black,...

Periodic Cleaning6-19
6
Maintenance
11Place the end of the black, plastic loop over the end of the stub, 
so that it stays in place.
12Close the ADF cover, and press down on it slightly until you hear 
it lock into place. Then, lower the document feeder tray.
IMPORTANT
 Make sure that you have put the black, plastic loop back in place before you close the 
ADF cover.
13Connect the power cord of the main unit to the power source.
 

Periodic Cleaning6-20
Maintenance
6
Cleaning the Roller
If black streak appears on outputs, the fixing roller in the main unit may be dirty. In such a case, 
clean the roller.
Load A4 size paper in the MP tray to clean the roller.
IMPORTANT
 Only A4 size paper can be used to clean the roller.
NOTE
 It takes about 130 seconds to clean the roller.
1Open the MP tray.
2Pull out the extension tray using the center grip a, then flip open 
the support tray b.
2
1