Canon Fax L2000ip User Guide

Periodic Cleaning6-21
6
Maintenance
3Load a A4 size paper into the MP tray.
4Open all three one-touch speed dialing panels.
5Press [Data Registration].
6Press [▼] or [▲] until  appears ➞ press [OK].
7Press [▼] or [▲] until  appears ➞ press 
[OK].
The machine starts cleaning the roller.
NOTE
 If a paper jam occurs, press   (Stop) and remove the jammed paper.
 Discard the cleaning paper after use.
Data
Registration
ADDITIONAL FUNCTIONS
1.PAPER SETTINGS
OKADDITIONAL FUNCTIONS
7.ADJUST/CLEAN➞ADJUST/CLEAN...

Refilling the Stamp Ink Compartment (Optional)6-22
Maintenance
6
Refilling the Stamp Ink Compartment 
(Optional)
Follow this procedure to refill the stamp ink compartment if you are using the optional stamp 
feature.
Please contact your local authorized Canon dealer when you run out of ink.
1Disconnect the power cord of the main unit from its power 
source.
2Lift the document feeder tray, and gently open the ADF cover 
until it stops, grasping the document feeder tray and the ADF 
cover at the same time.
 

Refilling the Stamp Ink Compartment (Optional)6-23
6
Maintenance
3While holding the ADF cover open with one hand, use one finger 
of your other hand to gently push in the black, plastic loop to 
separate it from the stub on the machine.
4Gently lift the ADF cover up to its full open position.
 

Refilling the Stamp Ink Compartment (Optional)6-24
Maintenance
6
5Locate the stamp pad, and apply only one drop of ink to the 
stamp ink compartment.
CAUTION
 To avoid spilling ink, apply only one drop of ink to the stamp pad.
IMPORTANT
 To avoid a malfunction, do not add too much ink, and make sure that the ink does not 
drip on any other part of the machine.
 Use only Shachihata X Stamper Ink CS-20 Yellow.
 Do not use the stamp feature for at least one hour until the ink is completely soaked up....

Refilling the Stamp Ink Compartment (Optional)6-25
6
Maintenance
6Lower the ADF cover until the black, plastic loop is even with the 
stub on the machine.
7Place the end of the black, plastic loop over the end of the stub, 
so that it stays in place.
 

Refilling the Stamp Ink Compartment (Optional)6-26
Maintenance
6
8Close the ADF cover, and press down on it slightly until you hear 
it lock into place. Then, lower the document feeder tray.
IMPORTANT
 Make sure that you put the black, plastic loop back in place before you close the ADF 
cover.
9Connect the power cord of the main unit to the power source.
 

CHAPTER
1-1
1
Before You Start Using 
This Machine
This chapter describes what you should know before using this machine, such as main features, parts and their functions, how to install the machine, and how to turn ON the main power.
Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-3
Standard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Clearing Document Feed Jams7-2
Troubleshooting
7
Clearing Document Feed Jams
To prevent frequent paper jams during document scanning, always check the pages before you 
feed them into the machine. (See Chapter 3, “Sending Documents,” in the Facsimile Guide.)
If a document is curled or wrinkled, make a copy of the original and scan the copy.
If a paper jam occurs during scanning, the Error lamp blinks red, and the following message 
appears on the LCD display:
Follow the procedure described below to clear...

7
Troubleshooting
Clearing Document Feed Jams7-3
3Pull the document straight out to remove it.
NOTE
 Always open the ADF cover before you attempt to remove a jammed document.
4Close the ADF cover, and press down on it gently until you hear 
it lock into place.
 

Initializing the Automatic Document Feeder7-4
Troubleshooting
7
Initializing the Automatic Document 
Feeder
If the document cannot be correctly fed into the automatic document feeder, follow the 
procedure below to initialize the ADF.
1Open all three one-touch speed dialing panels.
2Press [Data Registration].
3Press [▼] or [▲] until  appears ➞ press [OK].
4Press [▼] or [▲] until  appears ➞ press 
[OK].
The pick up roller inside the ADF is reset to its initial position.
5Press  (Stop) to return to the...