Home > Canon > Digital Camera > Canon EOS 5D Mk.4 Manual

Canon EOS 5D Mk.4 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Canon EOS 5D Mk.4 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 676
    							
    199
    u White Balance Correction N
    With just one shot, three images with different color tones can be 
    recorded simultaneously. Based on the color temperature of the current 
    white balance setting, the image will be bracketed with a blue/amber 
    bias and magenta/green bias. This f unction is called white balance 
    bracketing (WB-BKT). White balance br acketing is possible up to ±3 
    levels in single-level increments.
    Set the white balance bracketing 
    amount.
     In step 2 for “White Balance 
    Correction”, when you turn the < 5> 
    dial, the “ ” mark on the screen will 
    change to “     ” (3 points).
    Turning the dial to the right sets the B/
    A bracketing, and turning it to the left 
    sets the M/G bracketing.
    X On the right, “ Bracket” indicates the 
    bracketing direction and correction 
    amount.
      Pressing the < L> button will cancel 
    all the [ WB Shift/Bkt. ] settings.
      Press < 0> to exit the setting.
     Bracketing Sequence
    The images will be bracketed in the following sequence: 1. Standard 
    white balance, 2. Blue (B) bias, and 3. Amber (A) bias, or 1. Standard 
    white balance, 2. Magenta (M) bias, and 3. Green (G) bias.
    White Balance Auto Bracketing
    B/A bias ±3 levels 
    						
    							
    u White Balance Correction N
    200
     During white balance bracketing, the maximum burst for continuous 
    shooting will be lower.
      Since three images are recorded for one shot, it takes longer to record 
    the image to the card.
     You can also set white balance correction and AEB together with white 
    balance bracketing. If you set AEB  in combination with white balance 
    bracketing, a total of nine images  will be recorded for a single shot.
      When white balance bracketing is se t, the white balance icon will blink.
      You can change the sequence (p.483) and number of shots (p.484) for 
    the white balance bracketing.
      “Bkt. ” stands for bracketing. 
    						
    							
    201
    If the image comes out dark or the contrast is low, the brightness and 
    contrast can be corrected automatical ly. This function is called Auto 
    Lighting Optimizer. The default setting is [ Standard]. With JPEG 
    images, the correction is applied when the image is captured.
    In the < A> mode, [ Standard ] is automatically set.
    1Select [Auto Lighting Optimizer].
     Under the [ z2] tab, select [ Auto 
    Lighting Optimizer ], then press 
    < 0 >.
    2Select the setting.
      Select the desired setting, then press 
    .
    3Take the picture.
      The image will be recorded with the 
    brightness and contrast corrected if 
    necessary.
    3 Auto Correction of Brightness and Contrast
      Depending on the shooting conditions, noise may increase.
      If the effect of Auto Lighting Optimizer is too strong and the image is too 
    bright, set [ Low] or [Disable ].
      If a setting other than [ Disable] is set and y ou use exposure 
    compensation or flash exposure compensation to darken the exposure, 
    the image may still come out bright.  If you want a darker exposure, set 
    this function to [ Disable].
      When you set multiple exposures (p.268), HDR mode (p.263), or 
    highlight tone priority (p.206), [ Auto Lighting Optimizer] will be 
    automatically set to [ Disable].
    In step 2, if you press the < B> button and remove the [ X] mark for 
    [ Disabled in M or B modes ] setting, the [Auto Lighting Optimizer ] can be 
    set even in the < a> and < F> modes. 
    						
    							
    202
    This function reduces the noise generated in the image. Although noise 
    reduction is applied at all ISO speeds, it  is particularly effective at high 
    ISO speeds. When shooting at low ISO speeds, the noise in the darker 
    parts of the image (shadow areas) can further be reduced.
    1Select [High ISO speed NR].
      Under the [ z3] tab, select [ High ISO 
    speed NR ], then press < 0>.
    2Set the level.
      Select the desired noise reduction 
    level, then press < 0>.
      M : Multi Shot Noise Reduction
    This applies noise reduction wi th higher image quality than [High]. 
    For a single photo, four shots  are taken continuously and aligned 
    and merged automatically in to a single JPEG image.
    If the image-recording quality is set to RAW or RAW+JPEG, you 
    cannot set [ Multi Shot Noise Reduction ].
    3Take the picture.
     The image will be recorded with noise 
    reduction applied.
    3  Setting Noise Reduction N
    High ISO Speed Noise Reduction
    You can set to display  in the viewfinder and on the LCD panel for 
    when Multi Shot Noise Reduction is set (p.489). 
    						
    							
    203
    3 Setting Noise Reduction N
    Cautions for Setting Mult i Shot Noise Reduction
      If there is significant misalignment in  the image due to camera shake, the 
    noise reduction effect may become smaller.
      If you are handholding the camera, keep it steady to prevent camera 
    shake. Using a tripod is recommended.
      If you shoot a moving subject,  the moving subject may leave 
    afterimages.
      The image alignment may not function properly with repetitive patterns 
    (lattice, stripes, etc.) or flat, single-tone images.
      If the subject’s brightness changes as  the four consecutive shots are 
    taken, irregular exposure in the image may result.
      After shooting, it may take some time to record an image to the card after 
    performing noise reduction and merging the images. During the 
    processing of the images, “ buSY” will be displayed in the viewfinder and 
    on the LCD panel, and you cannot take another picture until the 
    processing is completed.
      You cannot use AEB and WB bracketing.
      If [z 3: Long exp. noise reduction ], [z 3: Multiple exposure ], [z 3: 
    HDR Mode ], Dual Pixel RAW shooting, AEB shooting, WB bracketing, or 
    Live View shooting with Servo AF is set, [ Multi Shot Noise Reduction] 
    cannot be set.
      This cannot be set for bulb shooting.
      Flash shooting is not possible. Note that the AF-assist beam of EOS-
    dedicated, external Speedlites will be emitted according to the [ 23: 
    AF-assist beam firing ] setting.
      Doing any of the following will auto matically switch the setting to 
    [ Standard ]: Setting the power switch to < 2>, replacing the battery, 
    replacing the card, selecting the < A> or < F> shooting mode, setting or 
    switching the image-recording quality to RAW or RAW+JPEG, or 
    switching to movie shooting. 
    						
    							
    3 Setting Noise Reduction N
    204
    For images exposed for 1 sec. or longer, noise (dots of light and 
    banding) typical of long exposures can be reduced.
    1Select [Long exp. noise 
    reduction].
     Under the [ z3] tab, select [ Long 
    exp. noise reduction ], then press 
    < 0 >.
    2Set the desired setting.
      Select the desired setting, then press 
    .
      Auto
    For exposures of 1 sec. or longer , noise reduction is performed 
    automatically if noise typical of  long exposures is detected. This 
    [ Auto ] setting is effective in most cases.
      Enable
    Noise reduction is performed for all exposures of 1 sec. or longer. 
    The [ Enable ] setting may reduce noise that cannot be detected with 
    the [ Auto ] setting.
    3Take the picture.
     The image will be recorded with noise 
    reduction applied.
    Long Exposure Noise Reduction 
    						
    							
    205
    3 Setting Noise Reduction N
     With [ Auto] or [Enable ] set, the noise reduction process after the picture 
    is taken may take the same amount of time as that for the exposure. 
    During noise reduction, shooting is st ill possible as long as the maximum 
    burst indicator in the viewfinder shows “1” or higher.
      Images taken at high ISO speeds may look grainier with the [ Enable] 
    setting than with the [ Disable] or [Auto ] setting.
      With [ Enable ] set, if a long exposure is shot with the Live View image 
    displayed, “ BUSY” will be displayed during the noise reduction process. 
    The Live View display will not appear until the noise reduction is 
    completed. (You cannot take another picture.) 
    						
    							
    206
    You can reduce overexposed, clipped highlights.
    1Select [Highlight tone priority].
     Under the [ z3] tab, select 
    [ Highlight tone priority ], then press 
    < 0 >.
    2Select [Enable].
      Highlight details are improved. The 
    dynamic range is expanded from the 
    standard 18% gray to bright 
    highlights. The gradation between the 
    grays and highlights becomes 
    smoother.
    3Take the picture.
     The image will be recorded with 
    highlight tone priority applied.
    3  Highlight Tone Priority
     When [ Enable ] is set, noise may increase slightly.
      With [ Enable ], the settable ISO speed range will start from ISO 200. 
    Expanded ISO speeds cannot be set.
      When you set multiple exposures (p.268) or HDR mode (p.263), 
    [Highlight tone priority ] will be automatically set to [ Disable].
    When highlight tone is set, < A> is displayed in the viewfinder and on the 
    LCD panel. 
    						
    							
    207
    Peripheral light fall-off is a phenomenon that makes the image corners 
    look darker due to the optical characteristics of the lens. Image 
    distortion due to optical characteristics of the lens is called distortion. 
    Color fringing along subject outlines  is called chromatic aberration. And 
    decreased image sharpness due to the  aperture is called diffraction 
    phenomenon. These lens aberrations can be corrected. The Digital 
    Lens Optimizer can correct the variou s aberrations caused by optical 
    characteristics of the lens, diffraction phenomenon, and the 
    deterioration of resolution caused by the low-pass filter.
    By default, the [ Peripheral illum corr ], [Chromatic aberr corr ], and 
    [ Diffraction correction ] are set to [Enable], [Distortion correction ] 
    and [ Digital Lens Optimizer ] is set to [Disable].
    If the lens correction data is registered (saved) in the camera, 
    peripheral illumination correction,  chromatic aberration correction, and 
    diffraction correction will be done even in the < A> mode.
    If the setting screen displays [ Correction data not available ] or the 
    [ ] icon, it means that the correction  data for the respective lens is not 
    registered in the camera. See “Lens Correction Data” on page 213.
    1Select [Lens aberration 
    correction].
     Under the [ z1] tab, select [ Lens 
    aberration correction ], then press 
    < 0 >.
    2Select [Peripheral illum corr].
    3  Correction of Lens  Aberrations due 
    to Optical Characteristics N
    Peripheral Illumination Correction 
    						
    							
    3 Correction of Lens Aberrations due to Optical Characteristics N
    208
    3Select [Enable].
     Check that [ Correction data 
    available ] is displayed for the 
    attached lens.
      Select [ Enable], then press < 0>.
    4Take the picture.
      The image will be recorded with the 
    peripheral illumination corrected.
      Depending on shooting conditions, noise may appear on the image 
    periphery.
      The higher the ISO speed, the lower the correction amount will be.
    The correction amount applied will be slightly lower than the maximum 
    correction amount that can be applied with Digital Photo Professional (EOS 
    software, p.598). 
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon EOS 5D Mk.4 Manual