Brother DCP 8085DN User Manual

							58
16 Never push objects of any kind into this product through cabinet slots, since they may touch 
dangerous voltage points or short out parts resulting in the risk of fire or electric shock. Never 
spill liquid of any kind on the product. DO NOT attempt to service this product yourself because 
opening or removing covers may expose you to dangerous voltage points and other risks and 
may void your warranty. Refer all servicing to a Brother Authorized Service Center. For the 
location of your nearest Brother Authorized Service Center, please call: 
In USA: 1-877-BROTHER (1-877-276-8437)
In Canada: 1-877-BROTHER
17 Unplug this product from the AC power outlet and refer all servicing to Brother Authorized 
Service Personnel under the following conditions:
„When the power cord is damaged or frayed.
„If liquid has been spilled into the product.
„If the product has been exposed to rain or water.
„If the product does not operate normally when the operating instructions are followed. 
Adjust only those controls that are covered by the operating instructions. Improper 
adjustment of other controls may result in damage and will often require extensive work by 
a qualified technician to restore the product to normal operation.
„If the product has been dropped or the cabinet has been damaged.
„If the product exhibits a distinct change in performance, indicating a need for service.
18 To protect your product against power surges, we recommend the use of a power protection 
device (Surge Protector).
19 To reduce the risk of fire, electric shock and injury to people, note the following:
„DO NOT use this product near appliances that use water, a swimming pool or in a wet 
basement.
„DO NOT use the machine during an electrical storm. (There is the remote possibility of an 
electrical shock.)
„DO NOT use this product in the vicinity of a gas leak.
 
						

							Safety and legal
59
A Federal Communications Commission (FCC) Declaration of 
Conformity (USA only)A
declares, that the products
Product Name: DCP-8080DN and DCP-8085DN
comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the following 
measures:
„Reorient or relocate the receiving antenna.
„Increase the separation between the equipment and receiver.
„Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.
„Call the dealer or an experienced radio/TV technician for help.
IMPORTANT
• Changes or modifications not expressly approved by Brother Industries, Ltd. could void the 
user’s authority to operate the equipment.
• A shielded interface cable should be used to ensure compliance with the limits for a Class B 
digital device.
 
Industry Canada Compliance Statement (Canada only) A
This Class B digital apparatus complies with Canadian ICES–003. 
Cet appareil numérique de la classe B est conforme à la norme NMB–003 du Canada.Responsible Party: Brother International Corporation
100 Somerset Corporate Boulevard
Bridgewater, NJ 08807-0911 USA
TEL: (908) 704-1700
 
						

							60
Laser safetyA
This equipment is certified as a Class 1 laser product as defined in IEC 60825-1+A2: 2001 
specifications under the U.S. Department of Health and Human Services (DHHS) Radiation 
Performance Standard according to the Radiation Control for Health and Safety Act of 1968. This 
means that the equipment does not produce hazardous laser radiation.
Since radiation emitted inside the equipment is completely confined within protective housings 
and external covers, the laser beam cannot escape from the machine during any phase of user 
operation.
FDA regulationsA
U.S. Food and Drug Administration (FDA) has implemented regulations for laser products 
manufactured on and after August 2, 1976. Compliance is mandatory for products marketed in the 
United States. One of the following labels on the back of the machine indicates compliance with 
the FDA regulations and must be attached to laser products marketed in the United States.
Manufactured:
BROTHER Industries (Vietnam) LTD.
Phuc Dien Industrial Zone Cam Phuc Commune, Cam giang Dist Hai Duong Province, Vietnam.
This product complies with FDA performance standards for laser products except for deviations pursuant 
to Laser Notice No. 50, dated June 24, 2007.
Manufactured:
BROTHER TECHNOLOGY (SHENZHEN) LTD.
NO6 Gold Garden Ind., Nanling Buji, Longgang, Shenzhen, China
This product complies with FDA performance standards for laser products except for deviations pursuant 
to Laser Notice No. 50, dated June 24, 2007.
 
						

							Safety and legal
61
A
WARNING 
Use of controls, adjustments or performance of procedures other than those specified in this 
manual may result in hazardous invisible radiation exposure.
Internal laser radiation 
Max. Radiation Power: 5 mW
Wave Length: 770 – 810 nm
Laser Class: Class 3B
 
Disconnect deviceA
This product must be installed near an AC power outlet that is easily accessible. In case of 
emergencies, you must disconnect the power cord from the AC power outlet to shut off power 
completely.
LAN connectionA
CAUTION 
DO NOT connect this product to a LAN connection that is subject to over-voltages.
 
International ENERGY STAR® Compliance StatementA
The purpose of the International ENERGY STAR® Program is to promote the development and 
popularization of energy-efficient office equipment.
As an ENERGY STAR
® Partner, Brother Industries, Ltd. has determined that this product meets 
the ENERGY STAR
® guidelines for energy efficiency.
 
 
						

							62
Libtiff Copyright and LicenseA
Use and Copyright
Copyright© 1988-1997 Sam Leffler 
Copyright© 1991-1997 Silicon Graphics, Inc.
Permission to use, copy, modify, distribute, and sell this software and its documentation for any 
purpose is hereby granted without fee, provided that (i) the above copyright notices and this 
permission notice appear in all copies of the software and related documentation, and (ii) the 
names of Sam Leffler and Silicon Graphics may not be used in any advertising or publicity relating 
to the software without the specific, prior written permission of Sam Leffler and Silicon Graphics.
THE SOFTWARE IS PROVIDED AS-IS AND WITHOUT WARRANTY OF ANY KIND, 
EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY WARRANTY 
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR ANY SPECIAL, 
INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY 
DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, 
WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY 
OF LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
OF THIS SOFTWARE.
 
						

							Safety and legal
63
A
TrademarksA
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International Corporation.
Microsoft, Windows, Windows Server and Internet Explorer are registered trademarks of Microsoft 
Corporation in the United States and/or other countries.
Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the 
United States and other countries.
Apple, Macintosh, Safari and TrueType are trademarks of Apple Inc., registered in the United 
States and other countries.
Intel, and Pentium are trademarks of Intel Corporation in the U.S. and other countries.
PowerPC is a registered trademark of IBM in the United States and/or other countries.
AMD is a trademark of Advanced Micro Devices, Inc.
Adobe, Flash, Illustrator, PageMaker, Photoshop, PostScript and PostScript 3 are either 
registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or 
other countries.
Epson is a registered trademark and FX-80 and FX-850 are trademarks of Seiko Epson 
Corporation.
IBM and Proprinter are either registered trademarks or trademarks of International Business 
Machines Corporation in the United States and/or other countries.
Nuance, the Nuance logo, PaperPort and ScanSoft are trademarks or registered trademarks of 
Nuance Communications, Inc. or its affiliates in the United States and/or other countries.
Each company whose software title is mentioned in this manual has a Software License 
Agreement specific to its proprietary programs.
All other trademarks are the property of their respective owners.
 
						

							64
B
OptionsB
This machine has the following optional accessories. You can increase the capabilities of the 
machine with these items.
OptionsB
Lower tray unit SO-DIMM memory
LT-5300
  
 
						

							Options
65
B
Optional paper tray 
(LT-5300)
B
An optional lower tray can be installed, and it 
can hold up to 250 sheets of 20 lb (80 g/m
2) 
paper.
When an optional tray is installed, the 
machine can hold up to 550 sheets of plain 
paper.
 
For setup, see the instructions that we have 
supplied with the lower tray unit.
Memory boardB
This machine has 64 MB of standard memory 
and  one slot for optional memory expansion. 
You can expand the memory up to 576 MB by 
installing dual in-line memory modules (SO-
DIMMs). When you add the optional memory, 
it increases the performance for both copier 
and printer operations.
In general, the SO-DIMMs with the following 
specifications:
Type: 144 pin and 64 bit output
CAS latency: 2
Clock frequency: 100 MHz or more
Capacity: 64, 128, 256 or 512 MB
Height: 1.25 in. (31.75 mm)
Dram Type: SDRAM 2 Bank
 
The following web sites sell memory 
modules:
http://www.crucial.com/
http://www.kingston.com/
http://www.goldenram.com/
http://www.buffalo-technology.com/
Note
• There might be some SO-DIMMs that will 
not work with the machine.
• For more information, call Brother 
Customer Service.
 
 
						

							66
Installing extra memoryB
aTurn off the machine’s power switch.
bDisconnect the interface cable from the 
machine, and then unplug the power 
cord from the AC power outlet.
Note
Be sure to turn off the machine’s power 
switch before you install or remove the 
SO-DIMM.
 
cRemove the SO-DIMM cover and 
interface access cover.
 
 
dUnpack the SO-DIMM and hold it by its 
edges.
IMPORTANT
To prevent damage to the machine from 
static electricity, DO NOT touch the 
memory chips or the board surface.
 
eHold the SO-DIMM by the edges and 
align the notches in the SO-DIMM with 
the protrusions in the slot.
Insert the SO-DIMM diagonally (1), then 
tilt it toward the interface board until it 
clicks into place (2).
 
fPut the interface access cover and the 
SO-DIMM cover back on.
gPlug the machine’s power cord back into 
the AC power outlet first, and then 
connect the interface cable. 
hTurn on the machine’s power switch.
Note
To make sure that you have installed the 
SO-DIMM properly, you can print the user 
settings page that shows the current 
memory size. (See User Settings List 
on page 26.)
 
1
2
 
						

							67
C
C
TroubleshootingC
IMPORTANT
For technical help, you must call the country where you bought the machine. Calls must be 
made from within that country.
 
If you are having difficulty with your machineC
If you think there is a problem, check the chart below and follow the troubleshooting tips. You can 
solve most problems by yourself.
If you need additional help, the Brother Solutions Center offers the latest FAQs and 
troubleshooting tips.
Visit us at http://solutions.brother.com/
.
Copy difficultiesC
Troubleshooting and routine 
maintenance
C
DifficultiesSuggestions
Cannot make a copy. Contact your administrator to check your Secure Function Lock 
settings.
Vertical black line appears 
in copies.Black vertical lines on copies are typically caused by dirt or 
correction fluid on the glass strip, or the corona wire for printing is 
dirty. (See Cleaning the scanner on page 94 and Cleaning the 
corona wire on page 96.)