Barco Xlm Hd30 Owners Manual

6. Adjustment Mode
The new window will be added in the same position as it was previously removed. To change the position, go toEdit windowor
selectWindow adjustment,Position.
4. PressEXITto return to theLayout adjustmentmenu.
AConfirm Save layoutmenu will be displayed. When the active layout is read only, new name for layout will be proposed.
(menu 6-70)
5. PressENTERto confirm.
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then...

6. Adjustment Mode
TheEdit windowmenu is redirected to theWindow adjustmentmenu.
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then 
 to return
Menu 6-74
6.6.8 Keystone adjustment
What can be done ?
The keystone adjustment is used to align the image if the projector is mounted at a non standard projection angle. The keystone
adjustment influences the complete projected image (even when the image is composed by different windows)....

6. Adjustment Mode
Which blanking adjustments are available ?
• top blanking
• bottom blanking
•leftblanking
• right blanking
Image 6-19
Adjusting the blanking
1. Push the cursor key↑or↓to highlightBlanking. (menu 6-76)
2. PressENTERto display the blanking menu. (menu 6-77)
3. Push the cursor key↑or↓to highlight the desired blanking adjustment.
4. PressENTERto start up the chosen blanking.
5. Use the cursor keys to adjust the blanking.
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT...

6. Adjustment Mode
None
Output is locked on an internal sync
Input 1
Output is locked on source 1
Input 2
Output is locked on source 2
Input 3
Output is locked on source 3
Input 4
Output is locked on source 4
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then 
 to return
Menu 6-78
INPUT LOCKING
NONE
INPUT 1
INPUT 2
INPUT 3
INPUT 4
Select with↑or↓
 to accept
 to return
Menu 6-79
6.7 Scenergix
Overview
• Introduction
•...

6. Adjustment Mode
Adjustable overlapping area
50% 100%50% 100%
image 2 image 1
image 2 image 1
Light output per image
Total composite light output
Image 6-21
ScenergiX Basic Principle
6.7.2 Preparations
ScenergiX Preparations
To ensure proper ScenergiX adjustment, be sure that the following adjustments are done perfectly on all projectors:
• Convergence (Electronic Convergence).
• Geometry
• Color Matching (Color Temperature, Input Balance, Gamma)
6.7.3 ScenergiX
How to activate ?
1. Push the cursor...

6. Adjustment Mode
6.7.4 ScenergiX overlap zone (horizontal scenergix)
Definitions
Image 6-22
Scenergix set up
Overlap : number of pixels that overlap
Horizontal resolution of 1 projector : 1024 for Graphics versions, 1280 for Reality versions, 1400 for SXGA projectors.
Total horizontal screen resolution : [(horizontal resolution of 1 projector) x 2] minus overlap.
Horizontal Resolution source : number of active pixels of the source.
Adjustment of Active pixels (Pact) of thefirst projector
1. Go toFile...

6. Adjustment Mode
6.7.5 ScenergiX overlap zone (vertical scenergix)
Definitions
Image 6-23
Scenergix overlap zone vertical
Overlap : number of pixels that overlap
Vertical resolution of 1 projector : 768 for Graphics versions, 1024 for Reality versions, 1050 for SXGA projectors.
Total vertical screen resolution : [(Vertical resolution of 1 projector) x 2] minus (overlap)
Vertical Resolution source : number of active lines of the source
Adjustment of Active lines (Lact) of thefirst projector
1. Go toFile...

6. Adjustment Mode
A pattern with the different areas will be displayed. (image 6-24)
3. Use the cursor keys to move the border of the overlap area to the desired position (value between 0 and 255).
Setfirst the width of thefirst projector and repeat for the second one. (image 6-25, image 6-26)
SCENERGIX
STATUS [ON]
- size -
TOP
BOTTOM
LEFT
RIGHT
- black level -
LEVEL
Select with↑or↓
then 
 to return
Menu 6-82
Image 6-24
Width selections
84R59770014 XLM HD30 25/05/2009 

6. Adjustment Mode
Image 6-25
Width set up for projector 1
Image 6-26
Width set up for projector 2
6.7.7 Adjusting the black level of the images
Why
For dark images, the overlap zone will be brighter then the rest of the images. Therefore we can rise the black level of the remaining
image (excluding the overlap zone).
How to adjust?
1. Push the cursor key↑or↓to highlightLevel. (menu 6-83)
2. PressENTERto activate.
3. Adjust the black level of area A until the black level of area A, B and C are equal....

6. Adjustment Mode
ACB
12
13
11R
G
BRGB
Image 1Image 2
Image 6-27
Black level adjustment
86R59770014 XLM HD30 25/05/2009