Barco Xlm Hd30 Owners Manual

							6. Adjustment Mode
The new window will be added in the same position as it was previously removed. To change the position, go toEdit windowor
selectWindow adjustment,Position.
4. PressEXITto return to theLayout adjustmentmenu.
AConfirm Save layoutmenu will be displayed. When the active layout is read only, new name for layout will be proposed.
(menu 6-70)
5. PressENTERto confirm.
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then 
 to return
Menu 6-68
Add Window
Select Window to Add 
 to exit
Menu 6-69
CONFIRM
SAVE LAYOUT
Save changes to
Input 2 [2]
?
Select with←or→
Reprogram with↑or↓
or numeric keys
 to confirm
 to cancel
Menu 6-70
6.6.6 Remove a window in a layout
What can be done ?
One typical window in a layout can be removed out of this layout.
How to remove a window
1. Push the cursor key↑or↓to highlightRemove Window. (menu 6-71)
2. PressENTERto select.
TheRemove windowdialog box will be displayed. (menu 6-72)
3. Enter the source number of the source you want to remove from the layout.
4. PressENTERto confirm.
5. PressEXITto return to theLayout adjustmentmenu.
AConfirm Save layoutmenu will be displayed. When the active layout is read only, new name for layout will be proposed.
(menu 6-73)
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then 
 to return
Menu 6-71
Remove Window
Select Window to Add 
 to exit
Menu 6-72
CONFIRM
SAVE LAYOUT
Save changes to
Input 2 [2]
?
Select with←or→
Reprogram with↑or↓
or numeric keys
 to confirm
 to cancel
Menu 6-73
6.6.7 Edit window
What can be done ?
The selected window can be adjusted in size, position, z-order, etc. .
How to edit a window
1. Push the cursor key↑or↓to highlightEdit Window. (menu 6-74)
2. PressENTERto select.
R59770014 XLM HD30 25/05/2009
77 
						

							6. Adjustment Mode
TheEdit windowmenu is redirected to theWindow adjustmentmenu.
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then 
 to return
Menu 6-74
6.6.8 Keystone adjustment
What can be done ?
The keystone adjustment is used to align the image if the projector is mounted at a non standard projection angle. The keystone
adjustment influences the complete projected image (even when the image is composed by different windows).
Image 6-18
Keystone adjustment
How to adjust the keystone
1. Push the cursor key↑or↓to highlightKeystone. (menu 6-75)
2. PressENTERto select.
3. Push the cursor key←or→to adjust the keystone of the image.
When the upper part of the image is wider than the lower part of the image, push the cursor key←. The value indication below
the bar scale will be negative.
When the upper part of the image is smaller than the lower part of the image, push the cursor key→. The value indication below
the bar scale will be positive.
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then 
 to return
Menu 6-75
6.6.9 Blanking adjustment
What can be done ?
Blanking adjustments affect only the edges of the complete projected image and are used to frame the projected image on to the
screen and hide or blank out unwanted information (or noise). A ’0’ on the bar scale indicates no blanking.
78
R59770014 XLM HD30 25/05/2009 
						

							6. Adjustment Mode
Which blanking adjustments are available ?
• top blanking
• bottom blanking
•leftblanking
• right blanking
Image 6-19
Adjusting the blanking
1. Push the cursor key↑or↓to highlightBlanking. (menu 6-76)
2. PressENTERto display the blanking menu. (menu 6-77)
3. Push the cursor key↑or↓to highlight the desired blanking adjustment.
4. PressENTERto start up the chosen blanking.
5. Use the cursor keys to adjust the blanking.
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then 
 to return
Menu 6-76
BLANKING
TOP
BOTTOM
LEFT
RIGHT
Select with↑or↓
then 
 to return
Menu 6-77
6.6.10 Input locking
What can be done ?
The output signal can be locked on an internal generated sync signal or on the sync signal of one of the input sources. Locking the
output signal on an input signal can be required if motion artifacts occurs in that window or if frame delay for that input has to be set
to zero.
How to setup ?
1. Push the cursor key↑or↓to highlightInput Locking. (menu 6-78)
TheInput lockingmenu will be displayed. (menu 6-79)
2. Push the cursor key↑or↓to highlight the desired locking mode.
R59770014 XLM HD30 25/05/2009
79 
						

							6. Adjustment Mode
None
Output is locked on an internal sync
Input 1
Output is locked on source 1
Input 2
Output is locked on source 2
Input 3
Output is locked on source 3
Input 4
Output is locked on source 4
LAYOUT ADJUSTMENT
LOAD
RENAME
DELETE
ADD WINDOW
REMOVE WINDOW
EDIT WINDOW
KEYSTONE
BLANKING
INPUT LOCKING
Select with↑or↓
then 
 to return
Menu 6-78
INPUT LOCKING
NONE
INPUT 1
INPUT 2
INPUT 3
INPUT 4
Select with↑or↓
 to accept
 to return
Menu 6-79
6.7 Scenergix
Overview
• Introduction
• Preparations
• ScenergiX
• ScenergiX overlap zone (horizontal scenergix)
• ScenergiX overlap zone (vertical scenergix)
• ScenergiX size adjustment
• Adjusting the black level of the images
6.7.1 Introduction
Why ScenergiX ?
When working in a multichannel setup the XLM HD30 and its Soft Edge possibilities enable an image blending that gives the ap-
pearance of a single view, thus achieving realistic immersion for the majority of wide screen applications.
Image 6-20
Why Soft Edge?
What is the Basic Principal of ScenergiX ?
The principle of edge blending is archived by linear modulation of the light output in the overlap zone so that the light output in that
zone equals the light output of the rest of the image.
80
R59770014 XLM HD30 25/05/2009 
						

							6. Adjustment Mode
Adjustable overlapping area
50% 100%50% 100%
image 2 image 1
image 2 image 1
Light output per image
Total composite light output
Image 6-21
ScenergiX Basic Principle
6.7.2 Preparations
ScenergiX Preparations
To ensure proper ScenergiX adjustment, be sure that the following adjustments are done perfectly on all projectors:
• Convergence (Electronic Convergence).
• Geometry
• Color Matching (Color Temperature, Input Balance, Gamma)
6.7.3 ScenergiX
How to activate ?
1. Push the cursor key↑or↓to highlightScenergix.(menu 6-80)
2. PressENTERto select.
TheScenergiXmenu will be displayed. (menu 6-81)
3. Push the cursor key↑or↓to highlightStatus.
4. PressENTERto toggle betweenONandOFF.
ON ScenergiX is active
OFF ScenergiX is not active
ADJUSTMENT MODE
FILE SERVICE
PICTURE TUNING
WINDOW ADJUSTMENT
LAYOUT ADJUSTMENT
SCENERGIX
Select with↑or↓
then 
 to return
Menu 6-80
SCENERGIX
STATUS [ON]
- size -
TOP
BOTTOM
LEFT
RIGHT
- black level -
LEVEL
Select with↑or↓
then 
 to return
Menu 6-81
R59770014 XLM HD30 25/05/200981 
						

							6. Adjustment Mode
6.7.4 ScenergiX overlap zone (horizontal scenergix)
Definitions
Image 6-22
Scenergix set up
Overlap : number of pixels that overlap
Horizontal resolution of 1 projector : 1024 for Graphics versions, 1280 for Reality versions, 1400 for SXGA projectors.
Total horizontal screen resolution : [(horizontal resolution of 1 projector) x 2] minus overlap.
Horizontal Resolution source : number of active pixels of the source.
Adjustment of Active pixels (Pact) of thefirst projector
1. Go toFile Service–>Editmenu offirst projector.
2. Enter value for horizontal active (= Pact) as follows :
Pact = [(Horz. resolution of 1 projector)/(Total horz. screen resolution)] x (horz. resolution source)
3. Horizontal start (= Pstart) remains the same.
Adjustment of Active pixels (Pact) of second projector
1. Go toFile Service–>Editmenu of second projector.
2. Enter value for horizontal active (= Pact) as follows :
Pact = [(Horz. resolution of 1 projector)/(Total horz. screen resolution)] x (horz. resolution source)
3. Horizontal start (= Pstart) = original start + [(Horz. resolution source) minus (newly calculated Pact)]
Example
Horizontal resolution source : 1600 pixels
horizontal resolution projector 1 & 2 : 1024 pixels
Overlap : 100 pixels
Total horizontal screen size in pixels : 1948 pixels
Pact projector 1 = [(1024 / 1948)] x 1600 = 841 pixels
Pact projector 2 = [(1024 / 1948)] x 1600 = 841 pixels
Pstart projector 2 = Pstart projector 1 + (1600 – 841)
82
R59770014 XLM HD30 25/05/2009 
						

							6. Adjustment Mode
6.7.5 ScenergiX overlap zone (vertical scenergix)
Definitions
Image 6-23
Scenergix overlap zone vertical
Overlap : number of pixels that overlap
Vertical resolution of 1 projector : 768 for Graphics versions, 1024 for Reality versions, 1050 for SXGA projectors.
Total vertical screen resolution : [(Vertical resolution of 1 projector) x 2] minus (overlap)
Vertical Resolution source : number of active lines of the source
Adjustment of Active lines (Lact) of thefirst projector
1. Go toFile Service–>Editmenu offirst projector.
2. Enter value for vertical act (= Lact) as follows :
Lact = [(vert.. resolution of 1 projector)/(Total Vert. screen resolution)] x (Verti. resolution source)
3. Vertical start (= Lstart) remains the same.
Adjustment of Active lines (Lact) of second projector
1. Go toFile Service–>Editmenu of second projector.
2. Enter value for vertical act (= Lact) as follows :
Lact = [(Vert.. resolution of 1 projector)/(Total vert. screen resolution)] x (vert. resolution source)
3. Vertical start (= Lstart) = original start + [(Vert. resolution source) minus (newly calculated Lact)]
Example
Vertical resolution source : 1200 lines
Vertical resolution projector 1 & 2: 768 lines
Overlap : 50 lines
Total vertical screen size : 1486 lines
Lact projector 1 = (768 / 1486) x 1200 = 620 lines
Lact projector 2 = (768 / 1486/) x 1200 = 620 lines
Lstart projector 2 = Lstart projector 1 + (1200 – 620)
6.7.6 ScenergiX size adjustment
What can be done with the ScenergiX size menu?
Within this menu the width of the blending zone isset up.
How to adjust the size?
Only accessible when the status is in the ON position.
1. Push the cursor key↑or↓to highlight one of the four size adjustments, Top, Bottom, Left or Right. (menu 6-82)
2. PressENTERto select.
R59770014 XLM HD30 25/05/2009
83 
						

							6. Adjustment Mode
A pattern with the different areas will be displayed. (image 6-24)
3. Use the cursor keys to move the border of the overlap area to the desired position (value between 0 and 255).
Setfirst the width of thefirst projector and repeat for the second one. (image 6-25, image 6-26)
SCENERGIX
STATUS [ON]
- size -
TOP
BOTTOM
LEFT
RIGHT
- black level -
LEVEL
Select with↑or↓
then 
 to return
Menu 6-82
Image 6-24
Width selections
84R59770014 XLM HD30 25/05/2009 
						

							6. Adjustment Mode
Image 6-25
Width set up for projector 1
Image 6-26
Width set up for projector 2
6.7.7 Adjusting the black level of the images
Why
For dark images, the overlap zone will be brighter then the rest of the images. Therefore we can rise the black level of the remaining
image (excluding the overlap zone).
How to adjust?
1. Push the cursor key↑or↓to highlightLevel. (menu 6-83)
2. PressENTERto activate.
3. Adjust the black level of area A until the black level of area A, B and C are equal. (image 6-27)
SCENERGIX
STATUS [ON]
- size -
TOP
BOTTOM
LEFT
RIGHT
- black level -
LEVEL
Select with↑or↓
then 
 to return
Menu 6-83
R59770014 XLM HD30 25/05/200985 
						

							6. Adjustment Mode
ACB
12
13
11R
G
BRGB
Image 1Image 2
Image 6-27
Black level adjustment
86R59770014 XLM HD30 25/05/2009