Barco Xlm Hd30 Owners Manual

							3. Connections
How to insert an input module ?
1. Gently slide in the input module into a free input slot with the grip handle at the top.
2. Locking in the module by pushing the input module completely into the slot until a definite click is audible.
3.3.3 DVI input module
Technical info:
• Computer generated graphical source.
• DVI data in.
• 162 MHz pixel clock.
• Resolution from VGA to UXGA/60 Hz.
• DVI compliant.
• DVI loop through.
• Amber LED (upper LED on the front side) will be lit indicating module start up.
• When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges
the module.
D320 DVI
IN OUT
Image 3-5Image 3-6
Order info:
Article No. Description
R9850960 D325Digitizer DVI input module
3.3.4 SDI input module
Technical info:
• SDI data in.
• SDI loop through.
• 270Mbit/s transmission (SMPTE 259M-C).
• 525/625 interlaced.
• Coax (75 Ohm).
• Amber LED (upper LED on the front side) will be lit indicating recognition offilm, either continuous or intermittentfilm detection.
• When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges
the module.
D320 SDI
IN OUT
Image 3-7Image 3-8
Order info:
Article No. Description
R9850970
D325Digitizer SDI input module
R59770014 XLM HD30 25/05/200927 
						

							3. Connections
3.3.5 HDSDI input module
CAUTION:Maximum two HDSDI input modules may be inserted in one D325Digitizer.
Technical info:
• HDSDI data in (SMPTE292M).
• HDSDI loop through (SMPTE292M).
• Coax (75 Ohm).
• When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges
the module.
• Supported HDSDI standards:
- Progressive:
o1280x720/60/1:1/ (SMPTE 296M)
o1280x720/59.94/1:1/ (SMPTE 296M)
o1920x1080/30/1:1/ (SMPTE 274M)
o1920x1080/29.97/1:1/ (SMPTE 274M)
o1920x1080/25/1:1/ (SMPTE 274M)
o1920x1080/24/1:1/ (SMPTE 274M)
o1920x1080/23.98/1:1/ (SMPTE 274M)
- Interlaced:
o1920x1035/60/2:1/ (SMPTE 260M)
o1920x1035/59.94/2:1/ (SMPTE 260M)
o1920x1080/60/2:1/ (SMPTE 274M)
o1920x1080/59.94/2:1/ (SMPTE 274M)
o1920x1080/50/2:1/ (SMPTE 274M)
o1920/1080/50/2:1 (1250)/ (SMPTE 295M)
o1920x1080/24/Segmented/ (SMPTE 274M)
o1920x1080//23.98/Segmented/ (SMPTE 274M)
D320 HDSDI
IN OUT
Image 3-9Image 3-10
Order info:
Article No. Description
R9850980 D325Digitizer HDSDI input module
3.3.6 YUV / RG(s)B input module
Technical info:
• Component Video (BNC)
- R-Y : 0,7Vpp ±3dB 75 Ohm termination.
- Ys : 1Vpp ±3dB (0,7V Luma +0,3V Sync) 75 Ohm termination.
- B-Y : 0,7Vpp ±3dB 75 Ohm termination.
•RG(s)B(BNC)
- R : 0,7Vpp ±3dB 75 Ohm termination.
- G(s) : 1Vpp ±3dB (0,7Vpp G + 0,3Vpp Sync) 75 Ohm termination.
- B : 0,7Vpp ±3dB 75 Ohm termination.
• 3 BNC’s loop through connectors.
28
R59770014 XLM HD30 25/05/2009 
						

							3. Connections
• Amber LED (upper LED on the front side) will be lit indicating recognition offilm, either continuous or intermittentfilm detection.
• When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges
the module.
• Supports MacroVision™.
D320 YUV/RGSB
IN OUT
Image 3-11Image 3-12
Order info:
Article No. Description
R9850940 D325Digitizer YUV / RG(s)B input module
3.3.7 RGB analog input module
Technical info:
• Sub D15 connector for input and loop through.
• R, G, B, Hsync, Vsync : 0 to 1 Vpp ±3dB 75 Ohm termination.
• Black level : 300mV.
•Sync-tip:0V
• Resolution : SXGA and UXGA version available.
• Amber LED (upper LED on the front side) will be lit indicating recognition offilm, either continuous or intermittentfilm detection.
• When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges
the module.
D320 RGB-AN
IN OUT
Image 3-13Image 3-14
Order info:
Article No. Description
R9850950
D325Digitizer RGB analog SXGA input module
R9851710
D325Digitizer RGB analog UXGA input module
R9853120
D325Digitizer RGB analog input module
R59770014 XLM HD30 25/05/200929 
						

							3. Connections
3.3.8 CVBS / S-VID input module
Technical info:
• Video (BNC)
- CVBS : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination.
- BNC loop through connector.
• S-Video (4 pins DIN)
- Y : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination.
- U/V : 0,7Vpp ±3dB 100% color base, 75 Ohm termination.
- Chroma : Multi-Standard (PAL / SECAM / NTSC).
- 4 pins DIN loop through connector.
• Amber LED (upper LED on the front side) will be lit indicating recognition offilm, either continuous or intermittentfilm detection.
• When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges
the module.
• Supports MacroVision™.
D320 CVBS/S-VID
IN OUT
IN OUT
Image 3-15Image 3-16
Order info:
Article No. Description
R9850920 D325Digitizer CVBS / S-VID input module
3.3.9 Dummy input module
Technical info
• Dimensions : 103 x 181 x 41(W x D x H)
D320 DUMMYImage 3-17Image 3-18
Order info:
Article No. Description
R9850930 D325Digitizer dummy input module
30R59770014 XLM HD30 25/05/2009 
						

							3. Connections
3.4 Communication connection
Overview
• RS232/422 IN/OUT Serial network
• Ethernet connection
• Hardwired remote to CTRL 1
• Bi-directional communication port, CTRL 3
3.4.1 RS232/422 IN/OUT Serial network
RS232
An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the commu-
nication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for
relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard
with a set number of conductors, data rate, word length and type of connector to be used. The standard specifies com-
ponent connection standards with regard to computer interface. It is also called RS-232-C, which is the third version
of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ’0’ is > + 3V, Logical ’1’ is < -
3V. The range between -3V and +3V is the transition zone.
RS422
An EIA serial digital interface standard that specifies the electrical characteristics of balanced (differential) voltage,
digital interface circuits. This standard is usable over longer distances than RS-232. This signal governs the asyn-
chronous transmission of computer data at speeds of up to 920,000 bits per second. It is also used as the serial port
standard for Macintosh computers. When the difference between the 2 lines is < - 0.2V that equals with a logical ’0’.
When the difference is > +0.2V that equals to a logical ’1’..
Application
1. Remote control:
- easy adjustment of projector via a computer.
- allow storage of multiple projector configurations.
- wide range of control possibilities.
2. data communication
Pin configuration
MONITOR OUT
213
PUSH213
PUSH
HAR D WIR ED  R EMOT E 10/100 BA SE TSERIAL NET WORKMONITOR OUT
RS232/422 OUT RS232/422 INWIRELESS REMOT E
CT RL 3CT RL 2 CT RL 1 PORT 1PORT 2
BI-DIRECTIONAL UNI-DIRECTIONAL
Image 3-19
RS232/RS422 serial network connection
RS232/422 Serial Network IN
1
Data Carrier Detect (CD) 6 RXC+ Data Set Ready (DSR)
2 RXC- Receive Data (RD or RX or RXD)7
Request to send (RTS)
3 TXC- Transmitted Data (TD or TX or TXD)8
Clear To Send (CTS)
4TXC+ Data Terminal Ready (DTR)9
Ring Indicator (RI)
5 GND Signal Ground (GND)-
RS232/422 Serial Network OUT
1-
6RXB+
Data Set Ready (DSR)
2RXB-
Receive Data (RD or RX or RXD)7-
3TXB-
Transmitted Data (TD or TX or TXD)8-
R59770014 XLM HD30 25/05/200931 
						

							3. Connections
RS232/422 Serial Network OUT
4TXB+
Data Terminal Ready (DTR)9-
5 GND Signal Ground (GND)--
3.4.2 Ethernet connection
Connection
Connect port 1 or port 2 to a LAN by using a straight cable or a crossed cable. The connection is a 10/100 baseT.
MONITOR OUT
213
PUSH213
PUSH
HARDWIRED REMOTE 10/100 BASE TSERIAL NET WORKMONITOR OUT
RS232/422 OUT RS232/422 INWIRELESS REMOT E
CT RL 3CT RL 2 CT RL 1 PORT 1PORT 2
BI-DIRECTIONAL UNI-DIRECTIONAL
Image 3-20
Ethernet connection
The projector must have an IP address and the IP address of the connected PC must be within the same range of IP addresses.
Once getting access, it is possible to check and manipulate all projector settings. Remote diagnostics, control and monitoring be-
come very simple.
The 2 ports are functionally identical. Both ports are connected via the projector hub.
Pin configuration
Ethernet 10/100 base T Port 1 & 2
1TXD+5
++2.5VA
2TXD- 6 RXD-
3RXD+7
RXD-
4 ++2.5VA 8 GNDM
3.4.3 Hardwired remote to CTRL 1
How to connect
1. Plug one end of the remote cable in the connector on the bottom of the RCU. (image 3-21)
2. Plug the other end in the connector in the input panel of the projector labelled CTRL 1.
Specifications of the CTRL 1 input:
-U
in=9V
-I
max=80mA
• Internal IR receiver can be disabled:
omonojack: onpluginofthejack
ostereo jack : on plug in or using an external switch bringing the right channel (B) to ground level. (image 3-22)
32
R59770014 XLM HD30 25/05/2009 
						

							3. Connections
213PUSH213PUSH
COLORCONTRAS TPHASE S HARPNTI N TBRIGHTNSTANDB YENTER
TEXTEXIT
PAUSE2 14 3 56 80 9
7OK IR
GR EEN :  OPER ATIONAL
R ED :  STAND-B Y
Image 3-21
Hardwired RCU
1
2
AB C
D
2
3
1
Image 3-22
Stereo jack pin configuration
A tip : left channel
B ring : right channel
C screen : common (GND)
Dexternalswitch
1Stereojack
2 Mono jack
The Remote connection uses a standard two wire cable terminated on each end with a 3.5 mm male
(mono/stereo) phone jack.
This cable is not delivered but is available in most electronic or audio shops.
3.4.4 Bi-directional communication port, CTRL3
What can be connected
The rugged remote control can be connected to the Bi-directional communication port CTRL 3.
With this rugged remote control all control functions can be taken over. The LCD panel on this rugged remote displays the same
information as the panel on the projector itself.
Pin assignment two way connector
12
3
Image 3-23
R59770014 XLM HD30 25/05/200933 
						

							3. Connections
Pin Description
1
GND
2DATA+
3DATA-
How to connect via a cable ?
1. Plug one end of the twisted pare cable with XLR connector in the two way connector on the rugged remote (CTRL3). (image 3-24)
Fixed rate : 57600 baud
2. Plug the other end in the Bi-directional connector (CTRL 3) on the projector. (image 3-25)
Image 3-24
Rugged remote control, backside
213PUSH213PUSH
COLORCONTRAS TPHASE S HARPNTI N TBRIGHTNSTANDB YENTER
TEXTEXIT
PAUSE2 14 3 5680
9
7OK IR
GR EEN :  OPER ATIONAL
R ED :  STAND-B Y
Image 3-25
Bi-directional rugged remote control
How to set up the rugged remote control ?
1. PressADJkey once.
The main menu of the rugged remotecontrol will be started.
2. Push the cursor key↑or↓to selectInstal. Settings.
34
R59770014 XLM HD30 25/05/2009 
						

							3. Connections
3. PressENTERto select.
4. Push the cursor key↑or↓to selectCommunication.
5. PressENTERto select.
6. Push the cursor key↑or↓to selectComm. Port.
7. PressENTERto select.
8. PressENTERto toggle between [Auto], [XLR], [RS232] and eventually [RF]
Select the corresponding setting. Two are possible in this setup.
Auto The rugged remote listens to according its priority. XLR has the highest priority.
XLR
The rugged remote is forced to XLR.
3.5 Monitor output
What can be done ?
A monitor can be connected to this output to preview the projected image.
Pin configuration
Monitor output
1
Red Out8
Ground
2
Green Out9nc
3
Blue Out10 ground
4nc
11nc
5
Ground12nc
6
Ground13
Hor. Sync
7
Ground14
Ve r t . S y n c
R59770014 XLM HD30 25/05/200935 
						

							3. Connections
36R59770014 XLM HD30 25/05/2009