Barco Xlm Hd30 Owners Manual

							5. Getting used to the menu structure
5. GETTING USED TO THE MENU STRUCTURE
5.1 How to start up the menus
Box menu structure
The XLM HD30 has a box like menu structure which allows easy access to different parameters for setting up the projector.
How to activate
1. PressMENUon the RCU.
The main menu will start up. (menu 5-1)
↑or↓keys
• these keys are used to scroll through the available items within a menu box.
• these keys are used to make adjustments.
ENTER
•PressENTERto activate a selection
•UseENTERto confirm an adjustment.
BACK (EXIT)
•PressBACKto return to the previous menu. On rugged remote control,EXIT.
MENU (ADJ)
•PressMENUto start up the menu boxes
•PressMENUto exit the menu structure.
Key names between brackets correspond with the keys on the rugged remote control.
MAIN
Select a path from
below :
ADJUSTMENT MODE
INSTALLATION
SERVICE
Select with↑or↓
then 
 to return
Menu 5-1
5.2 Using the Dialog boxes
How to use the dialog boxes ?
Some parameters are modified by means of a dialog box, where selections can be made and/or values can be entered.
The values can be entered/adjusted in several way:
Bar scale adjustment with the arrow keys
1. Use the↑or↓key or the←or→to adjust the setting.
The bar scale will change. The value next to the bar scale will change accordingly.
Value adjustment using the numeric keys on the remote control
1. PressENTERto activate the inputfield.
Thefirst digit will be highlighted.
2. Enter the new value with the numeric keys on the remote control.
3. Select the next digit with the←or→key and repeat step 2.
4. Whenfinished, pressENTER.
Value adjustment using the arrow keys on the remote control
1. PressENTERto activate the inputfield.
R59770014 XLM HD30 25/05/2009
47 
						

							5. Getting used to the menu structure
Thefirst digit will be highlighted.
2. Press↑or↓to increase or decrease the value.
3. Press←or→to select the next digit to be changed.
4. PressENTERto confirm the changes.
5.3 Menu memory
Overview
Each menu with sub menus, remembers its last selected sub item even when leaving the menu structure and that as long as the
projector is running. When restarting the projector from stand-by, the menu memory is reset.
After re-opening the main menu and selecting an item, the previous selected sub item of that selected item is highlighted and can
be opened just by pressingENTER.
48
R59770014 XLM HD30 25/05/2009 
						

							6. Adjustment Mode
6. ADJUSTMENT MODE
Overview
• Adjustment mode overview
• Start up of the Adjustment mode
• File Service
• Picture Tuning
• Window Adjustment
• Layout Adjustment
• Scenergix
6.1 Adjustment mode overview
Overview
• File service
- Load
-Edit
- Rename
- Copy
- Delete
- Options
• Picture tuning
- Color space
- Color temperature
- Gamma
- Noise reduction
- Input balance
• Window adjustment
- Select source
-Size
-Position
- Z-order
- Color key
- Alpha blend
- No signal color
• Layout adjustment
- Load layout
- Rename layout
- Delete layout
- Add window
- Remove window
- Edit window
-Keystone
- Blanking
- Input locking
• ScenergiX
6.2 Start up of the Adjustment mode
How to start up
1. Select Adjustment mode. (menu 6-1)
2. PressENTERto select.
R59770014 XLM HD30 25/05/2009
49 
						

							6. Adjustment Mode
The adjustment mode menu will be displayed. (menu 6-2)
MAIN
Select a path from
below :
ADJUSTMENT MODE
INSTALLATION
SERVICE
Select with↑or↓
then 
 to return
Menu 6-1
ADJUSTMENT MODE
FILE SERVICE
PICTURE TUNING
WINDOW ADJUSTMENT
LAYOUT ADJUSTMENT
SCENERGIX
Select with↑or↓
then 
 to return
Menu 6-2
6.3 File Service
Overview
• Possiblefile manipulations
•Startup
• Loadfile
•Editfile
• Rename
• Copy
• Delete
• File Options
6.3.1 Possiblefile manipulations
Connecting a new source.
Before using a new source, a correctfile has to be installed. The projector’s memory contains a list offiles corresponding to the most
used sources. When the new source corresponds with one of thesefiles, thefile can be loaded and saved for future use. When
there is a little difference, thefile can also be loaded and then edited until the source specs are reached.
Possiblefile Manipulations
The followingfile manipulations are possible :
• Load : installation of afile for a new source.
• Edit : editing a loadedfile to the source specs.
• Rename : renaming afile.
• Copy : copying afile.
• Delete : deleting afile
• Options : manual / automatic
File attributes
Eachfile can have a ’read’ or ’read-write’ attribute.
The following situation can be found on the menus:
•r—:file is read only.
•rw-:file has a read-write attribute and can be edited.
6.3.2 Start up
Start up
To enter theFile Service, handle as follow :
1. Push the cursor key↑or↓to highlightFile Service. (menu 6-3)
2. PressENTERto select.
50
R59770014 XLM HD30 25/05/2009 
						

							6. Adjustment Mode
TheFile Servicemenu will be displayed. (menu 6-4)
ADJUSTMENT MODE
FILE SERVICE
PICTURE TUNING
WINDOW ADJUSTMENT
LAYOUT ADJUSTMENT
SCENERGIX
Select with↑or↓
then 
 to return
Menu 6-3
FILE SERVICE
LOAD
EDIT
RENAME
COPY
DELETE
OPTIONS
Select with↑or↓
then 
 to return
Menu 6-4
6.3.3 Loadfile
Start up Loadfile
To start up the loadfile, handle as follow :
1. Push the cursor key↑or↓to highlightLoad. (menu 6-5)
2. PressENTERto select.
TheLoadmenu displays the correspondingfiles depending on the installedfilter. (menu 6-6)
FILE SERVICE
LOAD
EDIT
RENAME
COPY
DELETE
OPTIONS
Select with↑or↓
then 
 to return
Menu 6-5
LOAD FILE FILTER LIST [Fit]
FilenameResAttrvga-txt 720x400 r--
*vga-txt[1] 720x400 rw-
-----------------------------
Active : vga-txt[1]
↑,↓,0, 8 to scroll,
←to toggle filter
 to load,
→to preview
 to return
Menu 6-6
Changing thefilter setting
1. Push the cursor key↑or↓highlightfilter list.
2. PressENTERto toggle the annotation between brackets.
[All] : allfiles that can be loaded will be displayed.
[Fit] : only the bestfittingfiles will be displayed (with a distinction of ± 2 lines and line duration of ± 300 ns).
Howtoloadafile ?
1. Push the cursor key↑or↓to select the bestfittingfile. (menu 6-7)
2. PressENTERto select.
3. PressENTERto confirm the new creation orEXITto return to the loadfile menu.
LOAD FILE FILTER LIST [Fit]
FilenameResAttrvga-txt 720x400 r--
*vga-txt[1] 720x400 rw-
-----------------------------
Active : vga-txt[1]
↑,↓,0, 8 to scroll,
←to toggle filter
 to load,
→to preview
 to return
Menu 6-7
During a loadfile, the actualfile is displayed next to the indicationActivefileand an ’*’ is set in the list.
R59770014 XLM HD30 25/05/200951 
						

							6. Adjustment Mode
The image is not perfect ?
If the displayed image is not correct after selecting the bestfittingfile, go to the Edit menu, select the activefile and change the File
settings.
6.3.4 Editfile
6.3.4.1 Start up
How to start up the Edit menu ?
1. Push the cursor key↑or↓to highlightEdit. (menu 6-8)
2. PressENTERto select.
The Editfile adaptation menu will be displayed (automatic positioned on the actualfile). (menu 6-9)
3. Select thefilewhichmustbeedited(mostlytheactivefile).
4. PressENTER.
Thefile name will be displayed in the upper right corner. (menu 6-10)
FILE SERVICE
LOAD
EDIT
RENAME
COPY
DELETE
OPTIONS
Select with↑or↓
then 
 to return
Menu 6-8
EDIT FILE
FilenameResAttr*vga-txt[1] 720x400 rw-
video525 675x180 r-
video625 675x556 r-
--------------------------
Active : vga-txt[1]
↑,↓,0, 8 to scroll,
 to accept,
 to return
Menu 6-9
EDIT FILE xga_60.s30
HORIZONTAL
TOTAL 1344 PIXELS
ACTIVE 1024 PIXELS
START 160 PIXELS
PERIOD 20678 nsec
VERTICAL (FIELD)
TOTAL 806 LINES
ACTIVE 768 LINES
START 9 LINES
OPTIONS
←,→ to adjust
 to return
Menu 6-10
6.3.4.2 Changing the settings
Different methods
The 3 different methods to change a setting will be described hereafter. These methods are:
• with the numeric keys on the remote control.
• with the arrow keys selecting the changing digit.
• with the arrow keys counting up or down.
How to change a setting with the numeric keys?
1. Push the cursor key↑or↓to highlight an item.
The color of the selected item will change.
2. PressENTERto activate the digits.
3. Enter directly with the numeric keys on the RCU or local keypad the new value.
How to change a setting with the cursor keys?
1. Push the cursor key↑or↓to highlight an item.
The color of the selected item will change.
2. PressENTERto activate the digits.
3. Push the cursor key←or→to select the changing digit.
4. Push the cursor key↑or↓to scroll to the desired digit.
5. Whenfinished, pressENTERto confirm.
How to change a setting with the cursor keys and counting up or down?
1. Push the cursor key↑or↓to highlight an item.
The color of the selected item will change.
2. PressENTERto activate.
3. Counting up or down by pushing the cursor key←or→.
52
R59770014 XLM HD30 25/05/2009 
						

							6. Adjustment Mode
6.3.4.3 Correct value
What is already available during start up?
During the installation of afile with LOAD, the horizontal period, the total number of vertical lines are automatically measured and
filled out in the menu table. These values will be available when starting up the EDIT procedure of an activefile.
CAUTION:Do not adjust these settings on an activefile, they are used to identify the input sourcefile.
How tofind the correct values for the item in the Editfile menu?
Horizontal Total Pixels If the value for Horizontal Total Pixels is wrong, sampling mistakes (small vertical bars in the
projected image) will be seen in the image.
Select Total and adjust the pixel quantity. Adjust for zero bars.
hint: if the number of bars increase, adjust in the other direction.
Active Pixels The Active Pixels : determine the width of the window on the screen. This value is normally given in
the source specifications. If not, adjust until full image is displayed (no missing pixels).
Horizontal Start number of pixels between the start of the sync signal and the start of the video information.
Horizontal Period
alreadyfilled in with the correct value when activefile.
Vertical Total Lines
alreadyfilled when an activefile is selected to be edited
Vertical Active Lines
number of horizontal lines determining the height of the projected image. This value is normally given
in the specification of the source. If not, adjust until full image height is displayed (no missing lines)
Vertical Start number of lines between the start of the sync pulse and the start of the video signal.
Hor. Total pixels
Active pixels
Hor. Pulse width
Hor. Start
Vert. Total lines
Active lines
Vert. Pulse width
Vert. Start
Hor. line
Frame
Image 6-1
Input settings
R59770014 XLM HD30 25/05/200953 
						

							6. Adjustment Mode
How to install the correct settings for the options in the Editfile menu.
EDIT FILE OPTIONS
Source number 1
Clamp delay 8
Clamp width 20
Film Mode Detection [on]
Banner Protect [on]
Select with↑or↓
←,→,  to adjust
 to return
Menu 6-11
Source number The source number of a non-activefile can be changed to any other source number. This makes it
possible to create afile for future source numbers.
Clamp delay The time between the leading edge of the clamp pulse and the locked edge of the sync pulse. Can be
any value between 0 and 255. Use the↑or↓keys to change the value.
Clamp width The width of the clamp pulse can be any value between 0 and 255. Use the↑or↓keys to change
the value.
Film mode detection:
[On] or [Off]Detects in the [on] mode if the source isfilm or video. Use theENTERkey to toggle between [on] or [off]
When enabled, the hardware looks for tell-tale signs of 3:2 or 2:2 pull-down sequences. These are the
result of converting cinema material recorded at 24 frames-per-second to the television frequencies
of 60 or 50 interlacedfields per second respectively. When FILM conversion is detected, the original
24 frames-per-second are restored. This avoids deinterlacing artefacts, and results in a perfect
artefact-free display. Note that in some cases (video clips, scrolling newstickers,...) FILM and VIDEO
material are mixed on one screen. This may confuse the detector and cause it to go into FILM
restoration mode. This will cause jaggies or motion artefacts. In such cases, disabling FILM mode
processing is the best cure.
Banner Protect: [On]
or [Off]Only active whenfilm mode detection is in the on position. Use theENTERkey to toggle between
[on] or [off].
FILM mode processing normally processes the entire display, but this may cause problems on sources
where video and FILM content are mixed. One very common example is scrolling banners at the
bottom of the screen (e.g.financial news). For those cases, the banner protect feature will force the
bottom quarter of the screen to be always processed in VIDEO mode, regardless of the rest of the
screen, which may be either video or FILM mode.
Sync
pulse
Clamp
pulse
Clamp
delayClamp
width
Leading edge
Trailinging edge
Image 6-2
Clamp delay and width
3:2 pull-down
Method used to map the 24 fps offilm onto the 30 fps (60fields) or 25 fps (50fields), so that onefilm frame occupies
three videofields, the next two, etc. It means the twofields of every other video frame come from differentfilm frames
making operations such as rotoscoping impossible, and requiring care in editing. Some sophisticated equipment can
unravel the 3:2 sequence to allow frame-by-frame treatment and subsequently re-compose 3:2. The 3:2 sequence
repeats everyfive video frames and fourfilm frames, the latter identified as A-D. Onlyfilm frame A is fully on a video
frame and so exists at one time code only, making it the editable point of the video sequence.
54R59770014 XLM HD30 25/05/2009 
						

							6. Adjustment Mode
2:2 pull-down
The process of transferring 24-frames/secfilm format into video by repeating each frame (used for PAL DVD’s) as two
videofields. ( AD )
Artefacts
Undesirable elements or defects in a video picture. These may occur naturally in the video process and must be
eliminated in order to achieve a high-quality picture.Most common in analog are cross color and cross luminance.
Most common in digital are macroblocks, whichresemble pixelation of the video image.
6.3.5 Rename
Start Up
To change the name of a selectedfile :
1. Push the cursor key↑or↓to highlightRename. (menu 6-12)
2. PressENTER.
The Rename selection menu will be displayed. (menu 6-13)
3. Push the cursor key↑or↓to select afile name.
4. PressENTERto select.
The Renamefile menu will be displayed with the selectedfile name alreadyfilled in, in the ’Fromfile name :’ area and in the ’To
file name :’ area. Thefirst character in the ’Tofile name :’ area is highlighted. (menu 6-14)
FILE SERVICE
LOAD
EDIT
RENAME
COPY
DELETE
OPTIONS
Select with↑or↓
then 
 to return
Menu 6-12
RENAME FILE
FilenameResAttrvideo525 675x180 r-
video625 675x556 r-
vga-txt 720x400 r-
-------------------------------
Active file : Video525
↑,↓,0, 8 to scroll,
 to accept,
 to return
Menu 6-13
RENAME FILE
From file name :
xga1
To file name :
xga2
Select with←or→
Reprogram with↑or↓
or numeric keys
 to confirm
 to return
Menu 6-14
Changing the characters
1. Push the cursor keys←or→to select the desired character. (menu 6-15)
Or,
Change that character by pushing the cursor keys↑or↓. Numeric characters can be entered directly with numeric keys on the
RCU.
Or,
PressENTERto confirm.
The renamedfile is entered in the list offiles.
2. PressEXITto return to the Rename menu selection.
No changes are made.
RENAME FILE
From file name :
xga1
To file name :
xga2
Select with←or→
Reprogram with↑or↓
or numeric keys
 to confirm
 to return
Menu 6-15
R59770014 XLM HD30 25/05/200955 
						

							6. Adjustment Mode
6.3.6 Copy
Start Up
To copy the name of a selectedfile :
1. Push the cursor key↑or↓to highlightCopy.
2. PressENTER.
The Copy selection menu will be displayed. (menu 6-16)
3. Push the cursor key↑or↓to select afile name.
4. PressENTERto select.
The Copyfile menu will be displayed with the selectedfile name alreadyfilled in, in the ’Fromfile name :’ area and in the ’Tofile
name :’ area. Thefirst character in the ’Tofile name :’ area is highlighted. (menu 6-17)
COPY FILE
FilenameResAttrvga-txt[1] 720x400 rw-
video525 675x180 r-
video625 675x556 r-
-------------------------------
Active file : Video525
↑,↓,0, 8 to scroll,
 to accept,
 to return
Menu 6-16
COPY FILE
Frome file name :
xga1
To file name :
xga2
Select with←or→
Reprogram with↑or↓
or numeric keys
 to confirm
 to return
Menu 6-17
Changing the characters
1. Push the cursor keys←or→to select the desired character. (menu 6-18)
Or,
Change that character by pushing the cursor keys↑or↓. Numeric characters can be entered directly with numeric keys on the
RCU.
Or,
PressENTERto confirm.
The copyfile is entered in the list offiles.
2. PressEXITto return to the Copy menu selection.
No changes are made.
COPY FILE
Frome file name :
xga1
To file name :
xga2
Select with←or→
Reprogram with↑or↓
or numeric keys
 to confirm
 to return
Menu 6-18
6.3.7 Delete
Start up and delete
To delete a selectedfile out of the list offiles :
1. Push the cursor key↑or↓to highlightDelete. (menu 6-19)
2. PressENTER.
The delete selection menu will be displayed. (menu 6-20)
3. Push the cursor key↑or↓to select afile name.
4. PressENTERto select.
Aconfirmation menu Deletefile ’file name’? is displayed. (menu 6-21)
56
R59770014 XLM HD30 25/05/2009