Barco Xlm Hd30 Owners Manual

3. Connections
How to insert an input module ?
1. Gently slide in the input module into a free input slot with the grip handle at the top.
2. Locking in the module by pushing the input module completely into the slot until a definite click is audible.
3.3.3 DVI input module
Technical info:
• Computer generated graphical source.
• DVI data in.
• 162 MHz pixel clock.
• Resolution from VGA to UXGA/60 Hz.
• DVI compliant.
• DVI loop through.
• Amber LED (upper LED on the front side) will be lit indicating...

3. Connections
3.3.5 HDSDI input module
CAUTION:Maximum two HDSDI input modules may be inserted in one D325Digitizer.
Technical info:
• HDSDI data in (SMPTE292M).
• HDSDI loop through (SMPTE292M).
• Coax (75 Ohm).
• When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges
the module.
• Supported HDSDI standards:
- Progressive:
o1280x720/60/1:1/ (SMPTE 296M)
o1280x720/59.94/1:1/ (SMPTE 296M)
o1920x1080/30/1:1/ (SMPTE 274M)...

3. Connections
• Amber LED (upper LED on the front side) will be lit indicating recognition offilm, either continuous or intermittentfilm detection.
• When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges
the module.
• Supports MacroVision™.
D320 YUV/RGSB
IN OUT
Image 3-11Image 3-12
Order info:
Article No. Description
R9850940 D325Digitizer YUV / RG(s)B input module
3.3.7 RGB analog input module
Technical info:
• Sub D15 connector for...

3. Connections
3.3.8 CVBS / S-VID input module
Technical info:
• Video (BNC)
- CVBS : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination.
- BNC loop through connector.
• S-Video (4 pins DIN)
- Y : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination.
- U/V : 0,7Vpp ±3dB 100% color base, 75 Ohm termination.
- Chroma : Multi-Standard (PAL / SECAM / NTSC).
- 4 pins DIN loop through connector.
• Amber LED (upper LED on the front side) will be lit indicating recognition offilm, either continuous or...

3. Connections
3.4 Communication connection
Overview
• RS232/422 IN/OUT Serial network
• Ethernet connection
• Hardwired remote to CTRL 1
• Bi-directional communication port, CTRL 3
3.4.1 RS232/422 IN/OUT Serial network
RS232
An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the commu-
nication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for
relatively short-range communications and does...

3. Connections
RS232/422 Serial Network OUT
4TXB+
Data Terminal Ready (DTR)9-
5 GND Signal Ground (GND)--
3.4.2 Ethernet connection
Connection
Connect port 1 or port 2 to a LAN by using a straight cable or a crossed cable. The connection is a 10/100 baseT.
MONITOR OUT
213
PUSH213
PUSH
HARDWIRED REMOTE 10/100 BASE TSERIAL NET WORKMONITOR OUT
RS232/422 OUT RS232/422 INWIRELESS REMOT E
CT RL 3CT RL 2 CT RL 1 PORT 1PORT 2
BI-DIRECTIONAL UNI-DIRECTIONAL
Image 3-20
Ethernet connection
The projector must have...

3. Connections
213PUSH213PUSH
COLORCONTRAS TPHASE S HARPNTI N TBRIGHTNSTANDB YENTER
TEXTEXIT
PAUSE2 14 3 56 80 9
7OK IR
GR EEN :  OPER ATIONAL
R ED :  STAND-B Y
Image 3-21
Hardwired RCU
1
2
AB C
D
2
3
1
Image 3-22
Stereo jack pin configuration
A tip : left channel
B ring : right channel
C screen : common (GND)
Dexternalswitch
1Stereojack
2 Mono jack
The Remote connection uses a standard two wire cable terminated on each end with a 3.5 mm male
(mono/stereo) phone jack.
This cable is not delivered but is...

3. Connections
Pin Description
1
GND
2DATA+
3DATA-
How to connect via a cable ?
1. Plug one end of the twisted pare cable with XLR connector in the two way connector on the rugged remote (CTRL3). (image 3-24)
Fixed rate : 57600 baud
2. Plug the other end in the Bi-directional connector (CTRL 3) on the projector. (image 3-25)
Image 3-24
Rugged remote control, backside
213PUSH213PUSH
COLORCONTRAS TPHASE S HARPNTI N TBRIGHTNSTANDB YENTER
TEXTEXIT
PAUSE2 14 3 5680
9
7OK IR
GR EEN :  OPER ATIONAL
R ED :...

3. Connections
3. PressENTERto select.
4. Push the cursor key↑or↓to selectCommunication.
5. PressENTERto select.
6. Push the cursor key↑or↓to selectComm. Port.
7. PressENTERto select.
8. PressENTERto toggle between [Auto], [XLR], [RS232] and eventually [RF]
Select the corresponding setting. Two are possible in this setup.
Auto The rugged remote listens to according its priority. XLR has the highest priority.
XLR
The rugged remote is forced to XLR.
3.5 Monitor output
What can be done ?
A monitor can be...

3. Connections
36R59770014 XLM HD30 25/05/2009