Barco Xlm Hd30 Owners Manual

4. Getting Started
4. GETTING STARTED
Overview
• Terminology overview RCU and local keypad
• Terminology overview Rugged remote control
• Switching on the projector
• Lamp runtime
• Switching to standby
• Switching off
• Using the RCU
• Using the Rugged remote control
• Projector address
• Controlling the projector
• Quick lens adjustment
4.1 Terminology overview RCU and local keypad
Overview
The following table gives an overview of the different functions associated to the keys.
COLORCONTRASTPHASE...

4. Getting Started
No. Key name Description
2 MENU Menu key, to enter or exit the menus.
3 Address key
(recessed key), to enter the address of the projector (between 0 and 9). Press the recessed
address key with a pencil, followed by pressing one digit button between 0 and 9.
4
LOGO keyLens adjustment key
5
PAUSE to stop projection for a short time, press ’PAUSE’. The image disappears but full power is
retained for immediate restarting.
6 STBY standby button, to start projector when the power switch is...

4. Getting Started
4.2 Terminology overview Rugged remote control
Overview
Image 4-2
Rugged remote control
No. Key name Description
1
STBY standby button, to start projector when the power switch is switched on and to switch off the
projector without switching off the power switch.
Attention : Switching to Standby. Whenthe projector is running and you want to go
to standby, press the standby key for 2 seconds.
2 ADJ Adjust key, to enter or exit the menus. corresponds with the Menu key on the remote...

4. Getting Started
4.3 Switching on the projector
Howtoswitchon
1. Press the tumbler switch in the “1” position (“ON” state indicated by a visible red section of the switch).
- When “0” is visible, the projector is switched off.
- When “1” is visible, the projector is switched on.
The projector starts in standby mode. The projector indication LED is red.
Start image projection
1. PressStandbykey once on the local keypad or on the remote control.
Note:It may take about 60 seconds before image projection,...

4. Getting Started
When switching to standby, it takes 15 seconds before the projector can be switched on again.
4.6 Switching off
How to switch off the projector?
1. PressfirstStandby.
2. Let cool down the projector until the fans stop blowing, at least 15 min.
3. Switch off the projector with the power switch.
4.7 Using the RCU
Pointing to a reflective screen.
1. Point the front of the RCU to the reflective screen surface. (image 4-3)
F
1F
2F
3
F
4
F
5
A
D
JE X
I T
E N
T ER
P A
U
S
E
P H
A
S
E T E
X
T
S...

4. Getting Started
Directly to one of the IR sensors
1. When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line)
(image 4-4)
The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the
remote control unit and the projector IR sensor.
F1F2F3
F
4
F
5A
DJEX
I
T
EN
TER
P
AUSE
P
HA
SE TE
XT
S
HA
RP
NTINT
COLO
R
BR
I
GHT
N
CONT
RTREBLE
BALA
NC
E
BAS
SVO
L 9
0
7
8
56
3...

4. Getting Started
Common address
Default address. Projector will always execute the command coming from a RCU programmed with that common
address.
Why a projector address ?
As more than one projector can be installed in a room, the separate projector should be separately addressable with an RCU or
computer. Therefor each projector has its own address.
Set up an individual Projector Address.
The set up of a projector address can be done via the software.
Projector controlling.
Every projector requires an...

4. Getting Started
4.10 Controlling the projector
Input Selection
Key in the corresponding slot number with the digit keys on the remote control. The selected source will be displayed.
Priority setting is done in the Input slots menu.
PictureControlsviatheRCU
When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. ’brightness...’ appears
on the screen (only ifTextboxin theDisplay Setupmenu is ON). The length of the bar scale and the value of the numeric...

4. Getting Started
C
A
B
D
Image 4-5
Lens adjustment with RCU
4.11.2 Lens adjustment via menus
How to adjust
1. Press theMENUbutton on the Remote control.
The main menu appears on the screen.
2. SelectInstallationand pressENTER.
3. SelectLensand pressENTER.
The lens menu will be displayed.
4. SelectZoom/Focusand pressENTER.
5. Use the↑and↓arrow keys to zoom, use the←and→arrow keys to focus.
6. PressBACKto return to the lens menu.
7. SelectShiftand pressENTER.
8. Use the↑and↓arrow keys for vertical shift,...

4. Getting Started
46R59770014 XLM HD30 25/05/2009